Search results for query: *

Installed and then uninstalled a Volquartsen hammer and sear now I cannot get enough travel out of the trigger to move the sear to drop the hammer. No parts left over and have installed and reinstalled the old and new parts several times. I still cannot get it to work. The trigger is barely...

Where else should I look for signs of wear for a 44 Mag S&W other than the top strap ? Barrel cylinder gap is the next obvious check. But what else can I check to see how bad the gun is worn ? To clarify, the top strap has MAJOR flame cutting. Looks like someone ran a hacksaw over it.

I am looking at setting up my Glock 22 for USPSA open class. What size dot would you recommend for a C-More Slide Ride ? what size dot are you using ? I was figuring 8 moa, I think that the 12 moa would be a little too big. But then again my eyes are not the greatest.

Looking for recommendations for getting choke tubes installed in one of my shotguns. I would prefer a national company that has a good reputation and would certainly be interested in an good or bad experiences that anyone has had. I have been thinking of sending it to Briley but their prices are...

Tried reloads, strong and weak, factory 3 dram 1 1/8 oz and they all do it. I have torn it down and reassembled and I see nothing wrong. Load 1 in chamber, a second in tube. Fire 1st round, bolt MAY go all the way back. If it does not the second shell is still on the carrier. If it does manage...

Want to install choke tubes in my new shotgun. Does anyone have good experience with one that does this kind of work and has a decent turn around time ?

I have been looking for a longer barrel and have heard that the SBE barrels will fit. Can anyone confirm this ?

The big evil Super Black Eagle just started to NOT fully cycle the bolt upon firing. It goes about 1/4 - 1/2" short and fails to load the second shell onto the elevator. I did a complete R&R on the trigger group and bolt. And it still does it. Does anyone have a suggestion on where I should look...

Was wondering if anyone has any idea of the current wait time for ATF to approve forms. I will have one pending as soon as my dealer gets it in his hands.

Need to tear down the bolt and remove the extractor to use my chamber gauge to build up some reloads. I CANNOT FIND MY M1A BOOK. Does anyone have a link to somewhere that has the info to tear apart the bolt? I think I remember how to get the op rod off and remove the bolt, but need some help...

Getting the box tomorrow with a Mann Accy Device and a new 03a3 stock. I am not sure if it is finished or not. Looks like it may have some Linseed oil on it. If not what should I put on it. I have some Military stock red spirit stain left over, or could continue with either Linspeed oil or Tung...

Do not really want to wait weeks or overpay for the 5th Edition book. I am hoping that there might be some load data for Red Dot in the book for the 12ga sabot slug.

I got an old Victory model S&W, the model 10, last week. I noticed that the ejector rod was not properly latching and was slightly bent. Got it straightened and it still is not latching all of the way. What else could be the cause and how do I fix it ? I smoothed out the latch end of the...

Not a scope really, off topic a little bit, but the crosshairs on my transit took a dump. All it needs are the two wires glued in and centered. Easy fix if you have black hairs to fix it with. Does anyone know of a shop that could do this ?

Trying to get info to do a trigger job on a Savage 93 rifle in 17 hmr. I have not been able to find good schematics, or details on how to take it all apart and get it back together for the trigger job. If anyone has any info I could use it.

I know it was here but cannot find it doing a search. If anyone has it I could use the link. It was a trainer type using a Garand stock with a 10/22 mounted inside it.

I have a 342-1 Ti hammerless, 38 spl humpback revolver that is missing a part. It is missing the pin that holds the frame mounted firing pin and spring inside the frame. It fell out and now I have a really expensive paperweight. I cannot find it inside any schematics on Midway, Brownells...

I am having trouble with my CMP Garand rear sight. When I turn the windage screw the elevation kicks in and starts to move the aperture up. I know things are most likely worn. But which parts need to replaced ? Trying to get it apart now. Not really that familiar with the internals YET. But...

I noticed a wide variaion between the loads that I had loaded before with Winchester small pistol primer and now with some I just loaded and put thru the Chrony with Federal primers. Otherwise would not be an issue but now the loads are light and if I add more powder and use Winchester primers...

Having trouble getting the sights for my G-23 everyone is out of Trijicon sights AND Glock brand night sights. Trijicon is quoting August as next delivery date and Glcok in general is stating beginning of May. Midway, Brownells, and everyone else that has a remotely decent price is out. Would...