I'm looking for a 1911 reciever in 10mm. I aquired a longslide with a breech face cut for 10mm. I'm having a heck of time finding a reciever for it though. Anyone know who makes them other than STI or Fusion. I'd like to stay away from ramped barrels if I can.
Another name for it is the .338 ultra cat. I'm re-enlisting soon and building one for long range elk. This site has reloading dies as well. http://www.z-hat.com/Ultracat.htm
I have an AR-30 in .330 Win mag. The barrels are already threaded with a cap installed. I don't remember the thread but you can get that from Armalite. Have your local smith ream and thread the break to match and you're good to go.
I've been waiting for SA to come out with an XD 10 mm and it doesn't look like it's going to happen. I'm looking at getting my XD 40 reemed to 10mm. Does anyone see any problem with this. I will need a stronger spring. I shouldn't have any problem with that. More comment the better...
The bullets I'm hunting with are 250 gr. hornady XTPs, hense the 296. My concern in this is that the blow-back is in the same place every time. I'll try to get pictures.
Oscar
Got a problem with a rifle. It's an EMF Hartford model in 45 colt. I was working my way up in loads for hunting and started having powder getting blown back through the action into my face. These loads were nowhere near max pressure. I did notice all the cases have soot all the way up the...
Not understanding
So if this tube reduces the pressure too much how does the full length rifle work? The reason I put it on in the first place was to try to bring the pressure down a little closer to normal.
Oscar
Just got back from the range after installing a pigtail gas tube. The rifle is a bushmater XM-15E2S(16" CARBINE). When fired the bolt carrier does not travel far enough to eject the shell. I used 3 different types of ammo including some hot varmint loads. Is it a spring issue or what. The...
My father wants to put an adjustable sight on his Kimber without getting his slide cut for the bomar style. Does kimber use a novak dovetail or do they use their own special dovetail? Will a novak sight work?
Oscar
SEAR
Well I've got one on order, went with the STI premium. I've used it in the past and I like it. As for the mainspring, standard. Left leg of the sear spring is almost even with the middle. The hammer hooks were done with a brand new ceramic stone so the they should be square. I think...
Good to be Aboard
The hammer falls to the half-cock position. I tried it with the trigger pulled and it happened once out of the few times while I was cycling dummies through the gun. I put in an old sear with almost no relief angle cut on it and the hammer hasn't followed since. Looks like...
I'm just finishing a project gun and about one out of 10 cycles the hammer will follow slide forward. I don't cycle it with an empty chamber, always with dummies to make it as real as possible. I installed an EGW fire control kit and fit the sear using the Eb Brown sear jig. I cut the relief...
I'm just finishing a project gun and about one out of 10 cycles the hammer will follow slide forward. I don't cycle it with an empty chamber, always with dummies to make it as real as possible. I installed an EGW fire control kit and fit the sear using the Eb Brown sear jig. I cut the relief...
thanks
thanks everyone for the replies. I was just made aware of some deals that caspian does for Military so I'm going to build a 10mm on there frame and slide. once again thanks for the replies.
Oscar1
Hello, I'm new around here. I'm looing for a good carry pistol in 10mm. I've looked at te dan wessons but I'm not a big fan of the external extractor. I realy don't want the slide cut for an adjustable sight either. Anyone know of other good 10mils that would be adequate for carry?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.