Hello folks,
I'm going on a couple day waterfowl hunt in NC for the first time! I'm so excited I can't decide what shotgun to take! My only concern is the brackish water damaging the finish on my benelli montefeltro silver or other blued barreled shotguns. I will thoroughly clean my gun...
Hello everyone. I was going to buy the smith wesson 15-22 rifle and discovered the HK 416 22lr rifle during the process. I like the 416 due to mostly metal construction. Out of the several reviews i've read/watched, only one didn't like it due to customer service and a broken extractor after...
I will be in st Louis may18-21 and would like to know if the area is concealed carry friendly? Also, recommendations for a good restaurant would be appreciated? I plan to eat at the shaved duck but others would be appreciated. I would also like to see or do something firearm/hunting...
I would appreciate powder suggestions for reloading lead cast bullets in 7.62x39 caliber. I intend on using either 115gr or 150gr round nose sized to 0.311" with a desired velocity of not more than 2000 fps to prevent gas checks. Please note that the powder needs to meter well in Hornady lnl...
I wanted to take a moment to thank and brag about my local IDPA Club at Mason Dixon Rifle Club (MDRC) in Morgantown, WV. For the last 2 years, our leaders have improved our IDPA program considerably by increasing the complexity of the stages, new props, more matches, organization, and...
I would appreciate some help regarding a new load I’m trying out in a XDS 45 using a lead bullet. The new load felt like the pressure exceeded the max load recommendation. When the round would go off, pressure was blowing very hard through the opening in the receiver where the trigger comes...
Is there any legal issue with a firearm that had the factory trigger replaced with an aftermarket trigger, which was used in a self-defense situation? Specifically, I've just started carrying a SW Shield, and would like to replace the factory with an Apex.
I now understand why so many like the 1911. I recently inherited a colt 1911a1 that was manufactured in 1942, and got to shoot it today for the first time. It has one of the smoothest actions I have ever experienced.
Anyways, it shoot's low. At 20 feet, it hits close to 10"-12" low. The...
There is a colt 1911 dated for 1942 with the initials on the inside of the wood grips. According to the serial number, it was issued for military use but I don't know what branch.
Is there a website, book, etc that references what personnel was issued which firearm?
I would like to...
I need help with the cam wire and wire guide for the Hornady Case Feeder. Specifically, the wire is to short and doesn't stay inside the guide because additional threading was added to lower the cam wire. This was done because not enough adjustment was available to properly time the sequence...
Im testing out a load for 40sw and getting the same speeds (fps) for a lighter bullet with more powder than a heavier bullet with less powder. I would think the lighter bullet would be faster with more powder, but its not.
Usually shoot 180gr RN rainer with 5.2gr WSF, chroned ~980 fps...
I would appreciate help with powder weight recommendations for the following.....
45acp
230gr lead cast round nose (penn bullets) (0.452")
large primer
WSF powder
I only have WSF to work with, would appreciate powder weight recommendations.
Several of us our buying Jim Stewarts Better Shotmaker and are looking for a punch list and or plans to set the machine up. Plans would include, how to set up a recirculation, type and size of pump, coolant, screens, holding tank, etc.
Any help would be appreciated.
I competed in an Idpa match at Atlanta Conservation Club today. What a great group of people. The match was well run and organized. I plan to return the next time I visit the area.
Highly recommend the club.
Is it legal to hip small arms ammo (7.62*39) to Illinois? Or is not worth it?
Ive read that the person receiving it needs to have a FOID card. As the shipper, what am supposed to do?
I'm helping a dear relative sale his Colt AR, but not sure on an asking price due to not finding much to compare it to. Would appreciate some help.
Colt AR 223, fixed stock, no forward assist, bayonet lug, same rifle used in vietnam.
Ballpark price?
I would appreciate any recommendations with the following load development or load data that you may shoot using WSF with 135gr bullets in 40sw
Tested out new load for 40sw at the range w/ XD...
OAL ~1.125"
7.3gr WSF
135gr Berry's RNFP (0.401")
Win SPP
Ave 1134 fps
Power Factor =...
I'm going to sale bulk ammo to help a relative and I would appreciate my fellow highroaders to identify and price this ammo at fair market value.
Would greatly appreciate it.
1) What is the green crate 7.62x39 ammo (country of origin, reloadable or no, corrosive or non-corrosive, and...
What is a better media separator - Rotary (hand crank) or Lymans auto-flow?
I need better separation of the media from brass. My current process consists of vibrating a shifting pan over the Lyman 1200 bowl; however, even though this method gets 99.9% of the media, there is always a couple...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.