Search results for query: *

I have several thousand rounds through with the new sliders from the 5 tube case feeder I bought just to get the sliders and case gate for my machine (do not use case feeder as have collator feeding cases to the slider), but I have a "rod" inside the spring from the time I used the old sliders...

They were (maybe no longer) available if you want to PAY through the nose...... Part number TR5450 is molded parts. Well things are sure changing at LEE. Had my first bad experience with their new pricing for parts and free shipping went up to $100 orders. Cancelled my order. You can get the...

No need to "take ram out". With ram at top and no index rod installed it will slide of out of the lower cover. I put in the new clutch just because it came with the rod. One fellow who could not get the slow twist to index properly, changed clutch and was good..... GD

Of the 5 LEE inline bullet feeders I have there are 4 different ball sizes, 2.5mm to 3/16" but all are "Pistol Bullet Feed Body" and the "Rifle Bullet Feed Body" feeders look to have larger balls used. 45 Cal uses 2.5mm balls. I bet the Pistol and rifle bodies are all the same and the sleeve...

I do not think getting them out of the tray into the Z trough by any method other than manually was in the design. I believe the thought was the Z trough would be easier to empty down to a press than the triangular tray but is not that case in my operations of the new tray. I am not successful...

I agree with his assessment that it does not feed down the Z trough. After more testing, 500 small rifle run on SPP and another 500 on Bench Prime, the old triangular tray works better. Just running 100 at a time loaded into Z trough they do not feed on SPP 6000 or Bench Prime. The tray is...

You have to log in to Facebook I believe. GD

Yes, all testing was done with all primers loaded into the Z chute out of the square tray portion. Worked okay in limited test with shaker pin in SPP 6000 primer trough but no go without pin in trough to shake Super Tray. Just using factory primer trough on SPP 6000 with and without pin so...

Preliminary testing with small rifle primers showed that without the pin in the SPP 6000 primer trough, primers would not slide down the Z chute. With pin in primer trough primers fed very well and never ran me out of primers in the primer trough. Holding the new tray vertically primers feed...

I tried to get the "plastic parts" for the five tube but customer service refused to sell to me, even after a technician said it was available. Bought the whole thing to get the sliders and used their case gate on 3D printed case feeder setup as it puts less side load on the slider than mine...

Yes, those are the common problems. New sliders solved it for me. Pushing surface was redesigned, cup is not rounded to where it will drag back cases and tabs that hold it on rail are different than previous iterations which might remove some tilt. Just ran 250, 45 ACP without a failure to...

The new case pushers/sliders work much better than the ones which came for a long time with case feeders and some of us worked to fix and/or 3D print different ones. They are same height as old ones so work just fine. They solved 99% my issues with 44 mag and 45 ACP cases being inserted to the...

I knew "someone" would. I will order a new tray. GD

I am a little skeptical. Look at the bench prime video. Second layer of primers does not move down as case priming happens. And installed on the SPP 6000 the pin is still in place on the primer trough and they tap it to get primers to flow. Does not appear to flow primers by gravity in their...

For all those running 44 mag, 45 ACP and such with LEE 4 tube case feeder the new 5 tube case feeder case sliders have fixed all the inherent issues with inconsistent feed of these cases to the shell plate. There is no longer case pull back because the new sliders are very open in front and the...

I have been using the LEE square start expander plug for 45ACP for a short time now and to me it is well worth the $3.50. With it, the inline bullet feeder drops the bullet in and the bullet does not fall off, come out or tip when indexing to the seating die. I never touch the bullet as a...

Called Lee to buy just plastic parts and they would not sell me replacement plastic parts for the 5 tube. I wanted to try the case sliders to see if feeding large diameter cases to the SPP was improved over standard slider. Just looking for improved case slider for printed collator feeder...

I got a new SPP 6000 a little while back and all the known/discussed here updated parts were on it. Even a reduced diameter lower section alignment pin update which I had not heard about anywhere was on it. It came with standard index rod not slow twist. GD

Yep, somes good, more is better.................. GD

Yep, that is the deal. GD