Search results for query: *

Archangel ICD Lee discontinued because ther mould broke and they said there was not enough volume to justify re-tooling--

david r--measured height of disk I will use , it is .445-6", 11.33 mm is 0.4460"--I will use the number drills and throw charges measuring grains from each and record---thanks again--volume #'s on disk are a starting point for developing grains of powder drop--thanks

well david r you are now my hero--one reply sez buy one but none available anywhere, is dicontinued by Lee--I am continuing to improve on ACB unit, just replaced business card stock with flex plastic, used the SD camera card case which flexes somewhat enought to bend to shape--just tried it out...

what I need is the hole diameters on the micro-disk, did not realize they were tapered, just looking for a starting point in drilling new hols to make one work--dont know what would be possible if anything just a thought to get proper drop consistenly--Lee states somewhere there is approx. a 7%...

I have given up trying to find this discontinued item and now want to try and make my own by using one of the standard disks that I do not require (at least right now)--I am reloading 380 auto w/bullseye powder and I need less powder throw than.30 disk will give me ( .26-.28 ) I want to epoxy...

Natchez has sets http://www.natchezss.com/product.cfm?contentID=productDetail&brand=LE&prodID=LEE90623&prodTitle=Lee 38 Super Carbide 3 Die Set

Update well I loaded up my Bersa thunder 380, fired 2 clips, no ftf or ftf--must have a harder strike in the Bersa than the Bodyguard, Bg is new, next task is to load up factory ammo in BG and see what happens--

I understand that "flush" is not enough in seating primer--reading all above leads me to beleive that the primer is of a "hard" and or the depth of seat needs to be .004 below flush/case bottom???

I looked at all rounds as I loaded, checked the primer to be flush on flat surface and they were, also checked each for oal-all o.k.--

Well-thanks for all the replies--do not have Unique--shop owner told me to use Alliant Bullseye, I now have to get the formula for 95 and 100 grn cast bullets--will order the Lyman edition 4 book on cast loads as soon as I clear the current bill, shop owner tells me Bullseye, W231 and HP38 are...

david-r, orionegnr, beatledog7---thanks --will load the up into the bersa thunder its at least a da-sa so wont have to tug on the S&W 15# trigger twiest--thanks again to all-

Photo Biker I used a press to seat the primer, the press was on a stool and not very stable, loaded bullet on the down stroke and inserted primer and up stroke was wobbly--

thanks for all the replies--I have 21 yet unfired--will head back to the shop tomorrow and try to seat properly--My Lee 4 stage turret press ships this week and the dies etc probably the week after, hope to find some bullets by then, get the right formulation for-90 - 95-100 grn loads using...

well really dissapointed--while waiting for equipment I found a shop not to far away and went with the owners reccomendation on loading for my 380 acp S&W bodyguard and Bersa thunder 380--bougt Zapalky primers 4,4 sp boxer--used cast lead rn 118-20 grn, (by shop owner) and 2.0-2.1grn Bullseye...

thanks for the replys--going to get the Lyman book and looking for the 95 grn cast round nose in .355

1st forgive my ignorance, dont want to make a mistake--I want to reload the 380 acp bullet--I have a S&W 380 bodyguard and a Bersa thunder 380--bought the 2nd edition Lee handbook and it is in my lap constantly, however what I have to start is--Penn 100 grn TCBB lead bullet, CCI small pistol...