Search results for query: *

I have had a Pact electronic powder dispenser for over ten years. I have never had a problem with it. I don't load all the time. I load handgun and rifle. I throw a charge with a powder measure then dump the under charge into the powder pan and the dispenser completes the charge. Sometimes the...

I plan to go to Arizona or Colorado in 2013 to hunt prarie dogs. Maybe hunt ground squirles here in California. I am considering buying a Simmons Range Finder. Anyone have experience with the Simmons Range Finder. I have never used a range finder. Thanks Norman :confused:

:confused:I have some IMR PB powder that is at least ten years old & intend to use it to load some 38 Special rounds. It has been stored in my attic which is very large and can be walked around in but it does get hot. The attic could be lived in if finished. Old house. The powder has not been...

I would like to sell my Dan Wesson 357 Mag with a six & eight inch barrel. Anyone know what they are selling for? Thans Norman

I have a H & R Mod. 940 9 shot revolver and the screw that holds the vent rib down has been missing for years. Can someone tell me where I can get that screw or what it's length and thread size is ? Maybe I can buy a screw from a local hardware store or gunsmith that has a large stock of...

I am considering buying a 1873 Winchester Replica. Case hardened reciever. A Uberti or other manufacturer. Will these rifles handle Hot 45 L.C. loads ? I prefer a 44 Magnum but they are hard to find. Winchester Model 92 is not avaible now. Thanks Norman

I am going to buy a Henry Big Boy 44 Mag. rifle. I want to install a tang sight on the rifle. I like the Creedmoor type sight. I have done a little research and found prices from $65.00 to $500.00. I don't want to spend five hundred dollars. What should look for in regards to quality of a tang...

I have decided to coat my rifle bullets using HBN/Hexagonal Boron Nitrate/White Graphite. I found a source in Canada but they sell by the pound. I am looking for someone that will sell an ounce or two. Norman

I am thinking of buying some Patch Out Bore Liquid Cleaner that is made by the same company that makes Wipe Out Foam Bore Cleaner. Anyone use this stuff? I have been using Bore Tech Eliminator at the range to get copper out of the barrel and Sharp Shootr Foam Bore Cleaner when I get home...

I am considering buying a Troglo 8-32x44 mil-dot illuminated reticle scope. What is the quality of Truglo scopes. I will appreciate opinions on the quality of Truglo scopes. Thank You Norman:)

I installed a Timney Trigger in my Remington 700 and am trying to adjust it to 1 1/2 lbs. I have had it adjusted to 1 1/2 lbs. more than once and it passes all the tests except the takeing it off safety test. That is put it on safety then pull the trigger then take it off safety. When taken off...

I am considering buying Iosso case cleaner but I am told it does not throughly clean primer pockets. I have 1000 45 ACP cases and I would like to have the primer pockets clean. I don't want to manually clean the pockets. How good is Iosso for cleaning primer pockets ? :confused: :confused:

I am considering buying Iosso case cleaner. I have been told that it does not throughly clean primer pockets. I have one thousand 45 ACP cases and I would like to have the primer pockets clean. I don't want to manually clean each pocket with a primer pocket cleaner. How good a job does Iosso...

I am trying to re-assemble my Remington 700 BDL but cannot figure out how the bolt stop spring installs. Can anyone direct me to a web site or explain how the spring is installed. Thanks Norman:banghead: :banghead: :banghead:

Looking for 44 Special load using Alliant Power Pistol Powder. I am going to load 500 rounds of 44 special's and one powder I want to try is Power Pistol. I cannot find any loading data for this powder. I will be loading 185 gr. Bear Creek Moly Coated Bullet. Will appreciate any loading data for...

I have a 1911 Springfield that I am going to install a McCormick Trigger and Cylinder & Slide Hammer, Sear and Disconnector in. I know the trigger cannel of a Springfield is tapered and I will end up with vertical movement after I file the trigger shoe to fit the gun. How do I go about fitting...

I have a 1911 Springfield that I am going to install a McCormick Trigger and Cylinder & Slide Hammer, Sear and Disconnector in. I know the trigger cannel of a Springfield is tapered and I will end up with vertical movement after I file the trigger shoe to fit the gun. How do I go about fitting...

Has anyone used Bullet Slick Lubricant www.lubricationspecs.com. I bought some and have uses it on only 50 rounds of 45 ACP. Not enough for a through test. I have 200 rounds loaded that I will apply it to for more testing. It is suppose to decrease leading and copper fouling. I am going to start...

Looking for once fired 44 special brass. Anyone have some for sale or know where I can buy some ? Norman