Search results for query: *

Thank you kind Sir!!

Rada, I could use your expertise determining a model number. 38, K frame 6 shot, with 4 screw side plate. Ser. # C150150 this particular one was nickle plated. no model number behind the yolk. Thank you!!

Correct,no air weight on the barrel and an exposed hammer. Thanks!!!!

Rada, I could use you wisdom again! 2" barrel, J-frame, 5 shot, 38 special, 3 screw side plate, S/N 109371. Can you tell me what model this is? is it a model 36? Thanks in advance!

Response to your questions Rada, It says "38 S.&W. ctg" Barrel length is 5" There is an "I" over a "V" on the left side of lanyard hole prior to the serial number. There is a number stamped on the bottom side of the barrel on a flat spot where the ejector rod goes. It is " V...

Rada, need help with a model comparison I have a 38 S&W ctg revolver, with 4 screw side plate with serial number 230272. It looks like it has three triangles stamped in the shape of "bugle" at the beginning and end of the "38 S&W ctg" stamp on the barrel. It has a lanyard loop on the end of a...

RC-- 2" barrel with "38 S&W spc ctg." on the barrel. Will that help narrow it down? Thanks!

Rada-- looking for your assistance again. S&W 38 Caliber, K or L Frame square butt, 6 shot, with a 4 screw side plate. SN- C 161995. Can you tell me what model it is, and what the "c" represents? Thanks!!

Rada--Thanks for the 042 Year sounds about right. blued finish and definitely aluminum framed. Neat internal hammer, but no safety grip. I think it is a 042. Thanks!!!

Need help confirming model # I have an aluminum frame 38 caliber revolver J frame with an internal hammer, but no grip safety. Three screw side plate, and the serial is "BPE6012". It looks like it has "model D42" behind the cylinder pivot. This is the only 42 I have seen without a grip...

Super Thanks Rada, You hit the nail on the head with the first one. Definitely a screw in front of the trigger guard, and "Made in USA" stamped on the right hand side. Thanks So Much! Take care!

6 shot 38? model help Rada, Thanks in advance--I have a 6 shot revolver with 4 side plate screws, and I believe to be a 38 but am not certain the serial number is 514165, and need to know the model number and can you confirm the caliber--no markings on barrel to this effect, it is a short 2"...

Thank you and Merry Christmas As the holidays begin to arrive, I wanted to express my gratitude for your unwavering assistance to me with my sometimes "newby" questions. You have helped me out greatly. I hope you have a wonderful holiday season, and prosperous new year!!

Need your help again Rada Rada, S&W 32 Winchester, 6 shot, 4 screw side plate, diamond surrounding the mounting screw on plastic grips, round front sight, SN 30840. What model is it?

Rada, Thanks!! It does have a flat thumb latch, and 4 screws (sorry should have mentioned the number of side plate screws in original post) Thanks again!!

Need your help again Rada 38 special J Frame ramp sight S/N 39530 What is the model? Baby Chief? Thanks again in advance

Thanks Rada-- Can you tell me what model it is? Thanks for the info on the years. There is an uncheckered Diamond around the screw hole on the grips, so that helps a lot.

Rada one more time. Radagast, J frame, top loader- breach, 5 shot, I think is a 38 cal. Ser# 400662 As always your help is gratefully appreciated.

Rada one more time. .38 caliber, J frame, 5 shot, 2" barrel, Ser. # 7196 on the butt. Can you tell me if it is a model 36 "chief"? Thanks for the help!!

Helping a friend. Rada--One more time for a local friend. Nickle plated 38 caliber K frame-- Ser. # 746362 Thanks!!