Search results for query: *

I just leave it in my conversations so I can go back when I forget it (again). I'll send it to you

Nope, looks like they have some 44s and 45s, but nothing bigger

I'll be in NE washington this weekend. What places?

Yes, definitely some improvement, and it theoretically could come back to 100% but they doubt that will ever be the case. The biggest issue is thumb and grip strength

Yep, that's kind of also what I was hoping is that someone in the NW WA area would say "Oh check out XYZ range, they have a 460 you can rent." as I'm not aware of anything close by that has one available to rent.

No stress- I know these threads pop up all the time with people asking about the guns and opinions. And it's all valid info, I just didn't want my original request to get lost in the discussion.

I feel this has kind of devolved into a "this is the gun you should get," "that's too much," "bullets are hard to find," which is all fantastic dialogue and definitely not the first (or second, or millionth) post regarding that. I've personally seen grizzlies (while elbow deep in elk guts), seen...

Thanks- That's why I want to try and shoot one. I'm still very young (early 30s), so even though I lost (according to the physio) 60% I still have pretty decent strength in them. I can shoot all my calibers (380, 9, 38/357, 45 acp) with zero issue. I plan on wearing it in a cross chest holster...

As the title states, I'm looking to shoot a 460 S&W before buying one. I have weak wrists from a rugby neck injury that caused me to have multiple discs fused and lose about 60% strength in my wrists and want to make sure it won't mess me up before I order one. Any sort of set up is fine, I only...

Progressive (Hornady LNL) cases gauge fine after sizing These are the heavy crimped ones, I'll respond with pics of those that aren't crimped at all when I switch back over- I need to make a mess of 9mm first. It sounds like there isn't any voodoo though, so it's an issue with either the gauge...

Failure rate on other ammo- I just switched to 9 and loaded 200 rounds and only 1 failed check gauge. I'd say that's pretty normal for me. Very, very slight flare added (in the separate hornady flare die, not using PEX) Was doing a ladder, but these were all 5.2gr HP38 COL from hornady's 10th...

I've been looking for a while for a "medium quantity" (I.e. 1-5k at a time) 38 special FMJ (any weight) with crimp groove for less than 15 cents per and they just don't seem to exist. Does someone have a lead on a place that sells them?

I'm running into an issue when seating 45 acp. I'm using a hornady die that seats and taper crimps. After sizing the case it passes case check, but once I seat the bullet it fails every single time (and it's not even close). I'm using 230 gr 45 FMJs from RMR. I've tried no crimp, I've tried a...

Yea... That's not gonna happen with cabelas. If I had really thrown a fit they may have given me like a 5$ off coupon or something, but that's the best you're getting.

I mean, I also have a shotshell reloader so I figured I'd just make some play rounds and give it a go... but I ordered a pound of W231 and got a pound of super handicap. The picture was W231. The description was W231. The title was W231. But the SKU and barcode said super handicap, so that's...

So, not to necro an old thread... But update?! How has it turned out my man? Are you enjoying it?

Agree with all the above and have used most of them except: Arm or Ally- Had a slightly bad experience with them on 9mm once fired cases, but they're by far the cheapest for 9mm brass atm. Cabelas- Ordered a 1lb jug of a pistol powder and ended up getting a pound of a shotshell powder because...

Yea, I have one as well and 100% on the instructions. Add in the fact I tend to crush case mouths with an alarmingly regularity (like 1-3 per 100) with the PTX on 9mil and I might retire both as well. The powder drop is fantastic though.

Answer to some questions: No I don't trim pistol brass Wet tumbled with SS pins in a fart Bullets are from RMR (but I assume are actually armscor they're reselling) I just ran 300 more through, and I saw the issue some more (though far less, so it's likely a combination of thin brass, slightly...

I have a full length sizing die, then a PTX. If I remove the PTX entirely, the problem goes away. I'm going to try adding the actual case flare die I have instead of using the PTX and seeing if the problem still exists.