Search results for query: *

  1. P

    wc844 with 62gr fmjsc load data

    went out and shot some brass started off at 23.5gr,24gr,24.5gr,25gr,and 25.5gr ... 20rds of each no overpressure marks no heavy extractor marks,primers look good(they all looked flat really) ...... checked for cracks and see if it grew..if i didnt mark each round i dont think i could tell which...
  2. P

    wc844 with 62gr fmjsc load data

    thanks rj1 ..... just trying to get some info and compare things
  3. P

    wc844 with 62gr fmjsc load data

    hey im a bout to load some together ......i got some wc844,cci #41 ,62 gr fmjsc ,and 06 lc brass ....just looking to see if anyone has any good info for a good load...... checked some other websites and a good load is 26gr of powder.what do you think.thanks
  4. P

    better way to clean off brass

    ok i tumbled ,trimmed, and sized .......but i forgot about the lube on the brass for about 2months ...... im thinking about soap and hot water will do the trick .anyone got a better way?
  5. P

    trimming 40 brass

    whats the minimum and max lenght for trimming 40 brass?
  6. P

    Once fired .223 - overpressure? unsafe to use?

    does lc brass have that problem alot? my pockets feel pretty tight and no signs of pressure over load
  7. P

    62gr fmjscbt question

    bought some 62gr bullets that said were ss109.was wondering how to tell if they are the real thing . used a magnent and it stuck to it.so how can i tell from the real ones
  8. P

    wtb .223 lc 06 brass

    anyone know where to get some mil. brass? thanks
  9. P

    40. s&w components

    where can i find some good/cheap bullets......... thinking about using wsf powder, precision ammunition brand brass, and will any small pistol primer work? what would you recommend? thanks
  10. P

    ss109 loads with wc-844

    just comparing ss109 loads with you guys........seeing what other people load there ss109 with......thanks
  11. P

    Load needed for 62 gr. IMI bullet in AR

    i tried 27gr of wc844 w/62gr scbt .....worked really good
  12. P

    hot load question

    im thinking 27-27.5gr of wc-844, lc 06,62gr fmjscbt,cci #41 ..........it worked pretty good today
  13. P

    col question/problem

    im loading 223 brass ......i cut to 1.755 on the brass......using ss109 62gr fmjscbt.... some of the ss109 differ in size so i when i seat the bullet somtimes my col is not the same......... i have it set to crimp on the middle cannelure......do i need to separate the bullets by lenght or is...
  14. P

    case neck deburring/cleaning

    how is the rcbs trim mate ?????????? i dont 300-400 to spend .......is it easy to use and fast?
  15. P

    case neck deburring/cleaning

    once you size the brass and cut to lenght .........the neck has burrs on the inside and outside.........i have the ch4d deburring tool.......to process alot of brass takes a long time by hand......im wondering if anyone know a quicker way to clean the necks ........is there a machine i can buy...
  16. P

    processing 223 brass question

    thanks !!!!!!! its a pain trying to clean all that brass .........just wanted to make sure
  17. P

    1k of 40 cal brass cost?

    how many pounds does it take to add up to 1k of 40 cal brass??? thanks
  18. P

    processing 223 brass question

    well these are plinking ammo ................do i need to worry about putting a mark on the bullet???? not much burr on the outside
  19. P

    processing 223 brass question

    even if i was loading precision ammo/match ammo theres really no burrs.....just wondering if not chamfering would make a difference ?thanks
  20. P

    processing 223 brass question

    im trimming alot of brass on my forster trimmer........... i know its good practice to chamfer necks clean........... would it make a huge difference if i didnt ???when loading in station #1 (dillon550b) the burrs are gone and inside neck is clean ........dont know if the burrs got smashed down...
Back
Top