Search results for query: *

I have found loads of load data for .38 Special! Most of it is for either 4, 5, or 6 inch barrels. I have revolvers with 2 and 3 inch barrels. I currently use 4.0 grains of HP-38 with 158 grain, plated, Berry Flat Points. OAL of 1.450. Will my short barrel revolvers be more accurate with a...

Would someone please provide a list of the latest upgrade parts for the Lee Six Pack Pro press? Thanks in advance. Larry

Set down at my Lee Six Pack Pro and it won't index correctly. Indexing starts, but I have to nudge the shell plate into position. I am very new to this press. Any solutions? Larry

Need ideas for removing the safety pin. Others have said it drives right out. This one will not budge. I'm thinking of removing the bolt and trying my Arbor Press on the pin. Has anyone else had success with this? Any other suggestions?

Does anyone have any opinions about this shotgun? Such as effectiveness on game, recoil, weight and availability of ammo? I'm thinking it might be the ticket for an older fellow.

Loaded 43 rounds of .38 Special, Win cases, 148 grain, BB coated wadcutters, in a Dillon Square Deal B press. Picture shows lead shavings from those 43 rounds. It seems excessive to me.

Pictures have sure struck my fancy! I've been trying to locate one for a few days. Anyone have a Ruger model 5152 revolver, that would like to share their impressions of it?

I recently acquired a box of Missouri, PPC #2, .358 Dia., 148 grain, DEWCBB, Coated bullets. Brinell hardness of 12. I've never loaded any of these before. I'm thinking 3.3 grains of HP-38 for the powder, and crimping in the last groove. My questions are: 1) HP-38 is the only powder I have...

I recently acquired a used, like new, 1791 holster for my 4" GP100. Hard to fully insert the revolver, due to the holster not having a sight channel molded in. The 1791 line of holsters looks good. Finished well and has double stitching where it's needed I removed the front sight, taped a...

I have several hundred reloads for my 1911's, that fail the plunk test in my Glock 21. Never had a problem with the 1911s. I mostly used factory in the Glock. Now, I would like to use my reloads The info is: Winchester brass, Winchester large primers, 5.2 grains of HP-38, and 230 grain FMJs...

Does RCBS, or anyone else, make PTX expanders, that can replace the Hornady PTX expanders? If so, where might I purchase them from? Thanks.

I have a question about a 20 gauge Iver Johnson shotgun. The serial # (if you can call it that) is TCXC. It is stamped on the tang, just behind the trigger guard. TCXC is also stamped into the wood of the forearm, and the metal. The phrase -20 GAUGE CHOKE BORE BARREL AND LUG FORGED IN ONE- is...

Anyone experienced a broken Sector Gear on their Lee Auto Drum? If so, any thoughts? Did the gear fail, or was something else wrong? I switched my Auto Drum from my Classic Turret Press, to a Pro 1000 and the sector gear broke on the first powder throw. Differences . . . 1) the Turret...

Has anyone had any experience with the plastic ammo boxes from Harbor Freight? If so, good or bad?

I have a Blackhawk #3 pocket holster for my G42. Unfortunately the lower right of the holster bends in, and the holster loses a good part of it's function (avoid printing). Any ideas for a more rigid holster?

Does anyone have any information on some older CCI Primers. I assume that they are older primers. The 1st line says "200 0012" Then the letters CCI (much larger) on a red background. The box, more like a tray holder, is Yellow. The next three liners are; CCI 300 LARGE PISTOL PRIMERS...

Anyone have an opinion about the Kahr CW380? I want one, but I understand Kahr has an unfriendly, user warranty. Is that true?

Is RWS Ammo, 380 .ACP, 95 gr FMJ Match Grade ammunition good stuff? Can the cases be re-loaded?

Anyone had any experience disassembling an Arminius hw5 cylinder & crane assembly. I assume a pin is holding the star shaft, to the ejector shaft?

Anyone have any suggestions, for the proper sequence for stripping and re-assembly of H&R DA/SA rimfire revolvers? Specifically 649, 650 and 676 models.