Search results for query: *

To help you all get a better idea of what im talking about I basically just want to have a bull barrel and some checkering

Hey guys. about 2 or 3 years ago i collected a lot of 223 brass and derprimed it. I didnt have the time or bullets to reload them all so i put them in a box and left them there. I stumble upon them a little while ago and all the cases have small brown spots on them. Does anyone know what they...

Hey guys. Im interested in building a custom 1911 3" from scratch. I dont really want to spend $900 for a kimber. My basic question is, how hard is it to do yourself? the mechanical work that is not the finish work. Ive already built 2 ARs from scratch so im not totally incompetent. Thanks S

bump. i could really use some opinions of this barrel

no i dont have a lathe. thanks though. i think its time to take this to a gun smith as stupid as that sounds but i really dont want to mess up the reciever any more than it is and that pin just wont budge

Freezing it didnt work either. any other suggestions?

The vaccum cleaner suggestion didnt work. Im going to try the freezer suggestion next. wish me luck

it wont come out with any amount of shaking. im seriously thinking i destroyed this lower and it was a great price too a stag for only 109

actually mine is in 38 spc. On the barrel it says 38 spc but doesnt mention a +p

Ive got a SW 649-1 and as you can probably figure out from the title that im wondering if it is rated for +P. Any help or place you could point me too would be greatly appreciated Thanks S

Hey guys. I was putting together a lower today and the bolt detent fell into the dentent hole round end first before the spring was in there and now i cant get it out. Its seriously in there. Any suggestions on getting it out? Thanks S

The reason I ask is because i was installing a new flash hider on my upper, i used an action block and everything. But when i was taking the old flash hider off, my vise flexed. It was due to me using too thin washers to put under the screws to secure the vise to the bench. So really what i want...

Hey guys. I recently purchased a stag lower for an AR build. I found it for a great price and i couldnt pass it up. However I did note that it is a slightly lighter more grayish kind of reciever and the upper from my DPMS didnt match its color. I was wondering what uppers are made out there that...

Thats a nice looking rifle. Im in the middle of a build right now and i was wondering where you got your parts?

Hey guys im looking to do a build witht the DPMS 18" mk 12 barrel (http://www.dpmsinc.com/store/products/?prod=5826&cat=1918). I wondered if anyone had any experience with it or could speak to its accuracy and quality. Thanks S

Special Purpose Rifle. An Ar15 variant. Google Mk12 SPR. i need gas tube, gas block. Back up irons. a bolt. the whole buffer assembly and a free floated rifle length quad rail. But really im open to any ar15 parts besides a non rail free float. PM me if you have offers

Hey guys. im trying to build an SPR. Im basing it around a Stag Lower, an YMH upper, and a DPMS MK12 18" barrel. Im trying to use a magpul CTR stock and some sort of quad rail full length free float. My main problem at the point it keeping the cost down. Right now im hovering around 910 with...

Thanks TechBrute. exactly what i was looking for

The title pretty much says what my question is. Basically what length AR buffer tube do i need for a rifle length gas tube?. Can i use a carbine length buffer tube or do i need a rifle length one. Im trying to build an SPR and i need to know this information before i buy my parts Thanks S

Hey guys. The ejector on my 1911 commander has the rear mounting stud broken. In other words, the front stud is still in place allowing the gun to function rather normally although the ejector does wiggle. The rear mounting stud broke off and is stuck in its hole. How exactly can i remove it...