Search results for query: *

  1. T

    Beretta 96 Elite II holster needed

    I've looked high and low and can not find a "no thumb-break" paddle holster for my 96 Elite II. Seems like someone would offer one by now. Please help. Dan
  2. T

    Help reloading for my mini-14.

    Thanks to all for the help, I now have a place to start. Dan
  3. T

    Help reloading for my mini-14.

    I want to start reloading for my mini-14 (.223) and since the powders listed are not what I already have, I could use some help picking a powder and load. Something that throws good, (not pencil lead). Example, my 308 loves H380 and it throws great. I plan to start with the Sierra 52 gr...
  4. T

    38-40 info needed

    Thanks so much Jim, this will let him know where to start. Dan
  5. T

    38-40 info needed

    My son-in-law just inherited a 38-40 lever action rifle and wants to get a revolver in the same caliber. I've looked high and low and done searches but can't come up with anything. Is anybody making revolvers in this caliber. Thanks Dan
  6. T

    weak recoil springs on a Bersa Thunder 45

    I also have a Bersa 45 and would be very interested in the answer to your question. I've occasionally felt the same delay going into battery although it has not failed to chamber yet. Dan
  7. T

    Need advice on Elite II reloads.

    Thanks guys, the very very light tapper crimp did the trick. much better groups. Dan
  8. T

    Need help with Bersa 45

    Thanks Wally, I'll check it out. Dan
  9. T

    Need help with Bersa 45

    I've been having ejection problems. It will pull the empty brass half way out and jam the next round under it. I replaced the ejector, spring and pin and it started to tear chunks out of the base but still not eject. So I replaced the barrel, it is somewhat better but will still fail to eject...
  10. T

    Need advice on Elite II reloads.

    Thanks, I'll reset my setting die and try power pistol again. Dan
  11. T

    Need advice on Elite II reloads.

    Reloading 40 cal for the Elite II is giving me a fit. First, it won't shoot lead of any kind or any load without leading badly. Second, now that I'm using plated bullets, it won't lead but they are not accurate. With jacketed bullets it will hold about 3" at 25yds, with plated it will only hold...
  12. T

    Need help finding adjustable sights for ruger P97DC

    Thanks rde, they said they would send the highest rear sight they had. Dan
  13. T

    Need help finding adjustable sights for ruger P97DC

    My P97 shoots about 6" low with both full and target loads at 25 yds. Have been looking for a couple of hours for an adjustable sight. I need one that I can install myself. I'm sure someone here has already been though this and can help me out. Thanks, Dan
  14. T

    Bersa Usa, Good Service

    Bersa update Went to the range Saturday to test the new extractor parts. Turns out that besides the extractor, it also needs a new barrel. After many thousands of rounds, I've worn out the barrel and even with the new parts tearing chunks out of the brass, the old barrel won't let the brass go...
  15. T

    Bersa Usa, Good Service

    I've had extractor trouble that just got worse as time went on. It would pull the case half way out and jam the next round under it. What I found when I replaced the Extractor, pin, and spring was that the new spring was different. Smaller in diameter and I'm guessing that the new one is the...
  16. T

    Who doesn't have a CZ?

    I had a 75b in 40, sold it cheap. Not accurate and the trigger just sucked beyond belief. On the up side, it never malfunctioned and did look good. Dan
  17. T

    Bersa Usa, Good Service

    Ordered extractor parts for my Bersa 45 over the net. Received them in about a week with one small problem, they were for the Bersa 380. Called Bersa and told them that I also had a 380 so no harm no foil, but I still needed the 45 parts and was willing to pay again for them. Was told that they...
  18. T

    Ruger P97DC composite frame question

    Well, the warm oil and 0000 steel wool did the trick. Apparently the Hoppies bore scrubber dries out the composite, discoloring and making it appear to be etched. There are other cleaners that will do the same thing so I will be very careful from now on. Thanks for the suggestions, The wax idea...
  19. T

    Ruger P97DC composite frame question

    Call Ruger, they suggested warm oil rubbed in with very fine steel wool. Also told me I could try fine Scotch-bright with warm oil. I'll give it a try tonight. Dan
  20. T

    Ruger P97DC composite frame question

    The offending cleaner turned out to be Hoppies bore scrubber. I've used it on other guns for a long time with no problems but it is definitely the problem this time. Don't ask how I know for sure. Dan Buy the way, went to the range after work yesterday and this 45 is a keeper. It will hold...
Back
Top