Search results for query: *

  1. L

    Cimarron Uberti Colt 1873 Sight Alignment Problem

    I recently purchased a Cimarron Uberti Colt 1873 SAA in 45 Colt and 4 3/4" barrel. It is very accurate but consistently shoots to the left 2" at 7 yards. I would like to correct the front blade sight which appears to be mounted a little off to the right. I verified this with a laser sight. I...
  2. L

    Missouri Bullet order

    I would also like to have the current code. Thanks.
  3. L

    Cimarron Repair Service for Colt 1873 SAA

    9mmfan, Thanks for the info. Good shooting. lostbird
  4. L

    Cimarron Repair Service for Colt 1873 SAA

    I'm looking for contact information for the gunsmith that does warranty repair work for Cimarron in Fredericksburg, TX. I want to contact him about doing some non-warranty repair work on my Colt 1873. Any info would be very much appreciated.
  5. L

    45 Long Colt loads using WST powder

    walkalong, I'm going to start out with 4.5.grs of WST with the 250 gr cast LRNFP bullet. Published reloading data for this same bullet with a 19 burn rate indicates a load of 5.8 grs for 231 as a starting point with that powder. WST with a 15 burn rate loaded with 4.5 grs should be a safe...
  6. L

    45 Long Colt loads using WST powder

    Wil, Starting loads probably in the 750-850 fps and 8,000-11,000 psi range. No. I don't have chronograph. I don't have Bullseye. Just WST. Thanks for your interest Jerry
  7. L

    45 Long Colt loads using WST powder

    I'm looking for 45 Long Colt light loads using WST with 230-255 gr cast and jacketed bullets. Does anyone have any recommended "puff" loads they are willing to share? I know there are a lot of other powders out there for 45 LC, however, due to powder shortages WST is all I have on the shelf...
  8. L

    Cimarron Old Model 1873 Help

    I just purchased a Cimarron Old Model 1873 45 L.C. with a 4 3/4" barrel. I would like to get some information about it. The revolver is advertised to be an exact duplicate of the original Colt Model 1873 SAA manufactured from 1873 until 1896 and the parts are interchangeable. I'm looking for...
  9. L

    Identity and Date of Manufacture of S&W Revolvers

    Model 36 DOB Model 36(no dash) .38 Special 1 7/8" pinned barrel Nickel finish Round Butt S/N AEU13XX
  10. L

    Identity and Date of Manufacture of S&W Revolvers

    Thanks Radagast for the help and info. Great service you provide to THR members. lostbird
  11. L

    Identity and Date of Manufacture of S&W Revolvers

    Model 36 .38 Special 1 7/8" barrel S/N 702XXX
  12. L

    Plano TX FFL

    +1. Hart Sports. Great to deal with Tom.
  13. L

    Theater Shooting in San Antonio

    On Sunday December 17, 2012, 2 days after the CT shooting, a man went to a restaurant in San Antonio to kill his X-girlfriend. After he shot her, most of the people in the restaurant fled next door to a theater. The gunman followed them and entered the theater so he could shoot more people. He...
  14. L

    More fantastic work from TT Gunleather!

    I agree. Tim is a real gentleman and outsanding craftsman that takes a lot of pride in his work.
  15. L

    Best method for protecting sights from solvents and degreasers

    Thanks to all for your comments and suggestions. beatledog7- When I said "saturated" that was probably over stated. I clean the slide after every range trip usually firing 100-200 rounds and detail clean every 500 rounds. I like clean guns. I place the slide on the top and brush the...
  16. L

    Best method for protecting sights from solvents and degreasers

    I'm looking for the best method for protecting my Tritium Night Sights with White Outline from cleaning solvents and degreasers while cleaning. When I clean the slide I brush a liberal amount of Hoppe's or other solvents on the slide and let it sit for awhile. Then I go back and blow out the...
  17. L

    1911 Disassembly and Reassembly Video

    Thanks to all for your replies.
  18. L

    1911 Disassembly and Reassembly Video

    I'm looking for a quality video detailing the proper steps for disassembling and reassembling a 1911 pistol. Any recommendations or suggestions? Thanks for any help?
  19. L

    Hornady LNL AP EZject Problem

    I’ve been loading with my new Hornady LNL AP for a couple of months now and I’m having a problem with the EZject System. Shells frequently get jammed in the EZject station and it locks up the shell plate. This happens 3-4 times out of every 10 rounds or so. So far I've loaded only the...
Back
Top