LCP finger extension mag base plate
I got an after market finger extension mag buttplate for my LCP
(Ruger hadn't come out wiith their's yet)
I found it DID make a diference.
Less reliable with the extension.
Putting your pinky on the extension seems to "pry" the mag down a bit and I had a...
Here every goes trashing this guy and all but outright calling him a thief and con artist.
What reason is there to shut them down.
Could it not be just a super good deal. UNtil proven otherwise why not take the ad and guy at face value.
I know for a fact (got stung once) the US Post Office...
rolling file cabinets
I do just fine with "good quality" industrial style two drawer file cabinets
Mounted with a 2X10 piece of lumber "bolted" on.
The cabinets are mounted on rollers.
f You are worried about them rolling around
Just put a 4x4 under them to lift the wheels off the floor...
Zip guns
This "fella" I knew when I was Young...... :O)
built "Zip" Guns.
No One I knew ever used one to do harm
but we all thought we were "Cool Dudes" to have them around.
I'm sure the statute of limitations mjust have run out.
This was in Boston in the 1940s
"He" was inspired...
I Traded in my SIG (357Sig)
I Have remaining; Ten Pounds ( aprox 1000 ) .357 Sig > Brass.
Once Fired, Agency Indoor Range, Pick up
(That's the way it was sold to me)
How about........
$30 .......plus shipping ...(It will all fit into one flat rate Box)
What say You ...
Does anyone else have this problem?
When counting out brass ( from the tumbler into 100 count baggies)
I seem to get tiny "cuts" on my finger tips.
Sort of like "paper cuts" only much smaller.
They sting for DAYS afterward.
Sometimes my finger swells up.
Apparently the case mouths of the...
For Redneck2
I shoot at an Indoor Range
Max Distance 25 Yards
Limited to "Pistol" rounds
I am trying to simulate/emulate/prepare for > Bench Rest Target Shooting
Useing a TC Contender in "Carbine" configuration.
These two calibers were recommended to me as:
1. Meeting the range...
Alternate ( NOT H110) powder for 357 Rem Maximum
Have been playing with two new barrels for my TC Contender (in carbine configuration).
Hand Loading for:
357 Rem Maximum (180 and 158 grain Jacketed)
and
45 Winchester Magnum (230 grain Jacketed)
Working with the 45 Win Magnum...
Ok
I've been playing around without reliable facts for long enough.
Time to ask for help from those who know more than I ( I would hope).
I have a TC Contender in carbine configuration.
I shoot at an indoor range which is limited to 25 Yards and "Pistol" ammunition calibers.
I reload...
Want to load .45 Winchester Magnum for a 16"(+) TC Contender.
I have some Hard Cast Lead 260 grain bullets.
Am a little leary of driving Hard Cast lead down 16" of barrel.
Afraid of unacceptable leading if I drive them too hard
and I DO want stout loads ( what's the sense in wimpy .45...
OK
I get it
45 acp dies ( I have some ) should load 45 Win Mag fine.
I also have some 260 grain Hard Cast Lead 45 acp bullets (.452 I think)
What load ?
I want to drive them hard, but I don't want to lead up my 16 1/4 inch TC Barrel.
What Powder - How much of it ?
Can we talk about .45 Winchester Magnum...........
Where I shoot, I am restricted to "Pistol Calibers"
I have a TC Contender in Carbine configuration and am constantly on the look for "Long" (16"+) barrels for it in "Pistol Calibers".
Had an opportunity to pick up one in ".45 Winchester...
I have two versions of .38 spl Double Ended Wadcutter bullets
148 Hard Cast Lead - two lube rings wax filled ( They are "Zero" brand )
One is full flat on the business end
and
The other has a "Little Bump" in the center
I intend to put them over 2.5 of CLAYS
Question is:
Do I seat...
Not "RP" >> "AP"
I was taking micrometer readings of the "RP 357 Magnum Nickle plated" brass that was giving me problems.
Trying to figure out what might be "different" about it.
On closer Examination:
The Headstamp says "AP"......not "RP"
Armor piercing ???? I dont think so...
Came by a batch of > Headstamp = .
Tried to reload it on my 650.
All kinds of problems.
Hard primer seating - Sideways and upside down primers - Hard sizing - and >One Primer detonation on seating.
I had previously just finished a batch of mixed brass ( No nickle) without any...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.