Search results for query: *

  1. F

    Strong Mount

    Lower Chair! duh... what a novel idea. I will try that. Sometimes things are just too simple
  2. F

    Strong Mount

    I like the idea of the Dillon Strong Mount. Do you know if it will fit the LNL-AP or is there something else that fills that need? I like that it raises the press more to eye level. Does anyone make an aftermarket case counter?
  3. F

    Most Underappreciated Rifle Caliber

    22lr for this reason My 10 year old grandson shot my 22's for the first time last week. He has had a pellet gun for some time. I got out the 10/22, then the old stand by that was handed down to me from my dad. Of course I had to tell him the stories of all the squirrels and raccoon I had...
  4. F

    38 special data help

    thanks Thank you. Your answers are reassuring and helpful. We'll load up this morning and give them a try.
  5. F

    38 special data help

    I got some lead cast .358 125gr RNFP bullets to load in my J Frame just for practice rounds instead of burning up the gold dots. I got a couple of data books but having a hard time finding loads for this round. My gun will handle +P but wanting something a little softer for practice shooting...
  6. F

    Primers

    Just ordered some small rifle CCI in stock at Natchez. 9:20pm
  7. F

    Hornady Problem

    I checked the cases.. the cases were all 223 Rem. Whew! had me there for a minute. They were bought as once fired and all were trimmed. I think it is the adjustment. The instructions with the press were just a bit vague I thought. I realize I may be able to skip the trim function next...
  8. F

    Hornady Problem

    thank you for your replies. The cases are crushing inward as in the first reply. I do not bell the 223 cases and believe I have the correct powder drop since only 4 cases in 500 have this problem. I will try to adjust again, as perhaps that is the problem. I was puzzled why only 4 cases. I...
  9. F

    Hornady Problem

    I have been loading 223 Rem ammo with my Hornady AP press. After about 500 rounds I have 4 cases that somehow are getting belled on the top when going through the powder measure. Then the bullet will not fit in case. Spills powder every where when this happens and make the case unusable and loss...
  10. F

    Show us a picture of your reloading bench

    Material The legs are from a kit by 2x4basics. They are plastic and slide on the floor so the bench can be moved if needed. The shelves are 3/4" plywood. everything except the top stringers are 2x4. I used 2x6 for the top stringer to give an additional 2" height for the top. The finished...
  11. F

    Show us a picture of your reloading bench

    Safe on Rollers Well the safe is on rollers is for several reasons. the dakota safe comes in 4 boxes. It is installed in a basement and would never make it up the stairs at 700 lbs. And it would be difficult for someone to try and put a pry bar to the safe as it is not ridgid and would be...
  12. F

    Show us a picture of your reloading bench

    Just finished my bench,
  13. F

    Chambering problem for 223

    My friend has a Remington VTR in 223. WE loaded some Win. bullets 64gr. Full length resizing, They are military brass. ( L - C ) Dimensions read what case is suppose to be but man do they chamber hard. We had one case that just would not chamber. Is all the military brass like that?
  14. F

    .223 help 68gr bullets, Win 748 powder

    Look at the Winchester Data for 64gr PP. 64 GR. PP 64 748 .224" 2.120" 25.0 2970 47,500 PSI Why is the OAL only 2.120. That seems pretty short to me.
Back
Top