I managed to find some bullets to reload but found out they are old AP rounds. Took on apart because it looked way too long to only weigh 152 GR. Did weigh several and they are very inconsistent 152 down to 147. The bullets also have 2 cannelures. What would be a starting place for a charge...
I have a DPMS pattern lower and an aftermarket upper. Everything went together fine but when I chamber a round it does not extract . Trying to hand mount a round on the bolt face is extremely difficult. Have not shot it. I think the extractor is not grooved wide enough for the base of the...
I have a G19 GEN 3 I think...Was a poly 80 build in 9MM. I was told by a dealer that the frame is the same on a 19 and a 22. The internal parts are different along with the slide and of course the barrel. That being said I was pondering a 40 /357 sig build on a 19 frame. Is that possible...
I inherited a Winchester Model 94 in 3030. Looking on line in a few places to try to find out when it was born. Near as I can figure it's 61 or 62 SR# is 253XXXX. Has some pitting and light surface rust in places has seen some long days in the field. Action is smooth and barrel looks good...
Inherited a Luger. Wondering what it is. Safe to shoot and value.... should I shoot it. It's 9mm. Date on it is 1918 and it has a crown over ERFURT. From what I can tell without disassembling it the numbers match.
I piked up a S&W 686 and whit the shooting I do it going to need a new front end soon. Barrel is starting to get tied. Called S&W and they said they use sleeved barrels now. Anyone have any experience with these??? Any help or suggestions are appreciated.
I jut picked up a nice Model 66 and it is going to need to be re-barreled in the future. Has anyone had any experience with the new sleeved barrels from S&W. Thanks
Looking to buy a 9MM. Want it to have 17 shot cap. Ambidextrous controls. Have looked at Glock 17 Ruger SR9 and FNX The SIG329 looks good also. I do not want to buy and try. The question my Brothers is what do you have and why is it the best???? Any input would be great! Thanks for the help:)
Was reloading some range brass and found that SPEER and BLASER (brass case) are using small primers. Since when did they start using Small Primers????:confused:
Looking to put a bullet feeder on my press and was wondering which one to use. I have a Dillon 650 and was looking at the Lee due to its simple operation and cost . Does anyone out there have any experience with these and would it work with the Dillon. Seems like it would but I would need to...
Have a Pin Fire 5 shot revolver. Only marking on it is Y or 6 and SC under the wood grips. I will try to post photos but if they do not work anyone with knowledge with Pin Fires PM me PLEASE:confused:
I put out some heavy coin for a CMMG upper with the BHOA option and 2 mags. Mags needed to be worked in to even feed and I still can't get the bolt to stay open on the last round. Does anyone out there have any idea how long this takes to break in or did I get a lemon. Have tried it on a DPMS...
I am having trouble finding Load data for 148 GR double end Wad Cutters. I am going to use Tite Group. Wondering what the seating depth is I have seen Wad Cutters flush in the case. This is my first foray into revolver reloading. Any Help would be Great!!!:)
I would like to get something that shots .30 out of an AR platform and the ACC 300 does it but so does the 300 Whisper... I think. Would like to use standard mags,lower and bolt. Anyone one of you out there have any experience I would love to hear from you! I will be putting a can on it.:)
I was looking at the 6.5 and the 300 AAC. Both will work in an AR platform... Can you use the same mag for both or do you need to get new ones for the 6.5. From what I have found so far the 300 uses standard AR mags. Is the same true for the 6.5. So many choices. Just looking for some good...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.