primer

  1. B

    Current state of primer manufacturing

    I'm wondering if you have any input on the state of primer manufacturing in 2024. Everyone has their favorites, but manufacturing changes from over time and maybe primers that were great in 2003 or 2016 may not deliver in 2024. So I'm at Cabelas just a bit ago and they have a bunch of options...
  2. A

    Primer Making Die

    has anyone tried this? I am a prepper at heart and this seems like a good thing to have on hand https://recoilstore.com/infinite-primers-primer-cup-die/
  3. MoscowMike

    Expansion Industries Primer Plant

    In a recent post I mentioned that a gun shop clerk told me that the new Expansion Industries primer plant in Texas was not going to be built. No one seemed to have more info about it, but one poster said it had been a scam without providing details. There doesn’t appear to be anything new...
  4. L

    Primer vs. Primer vs. Primer

    I'm fairly new to reloading and have been mostly reloading pistol loads. I would like to load some rifle loads for hunting....30-06 and 308. I have no Large Rifle primers but I have the opportunity to get some at a local auction. I have 3 different manuals and they call out Winchester WLR, CCI...
  5. merlynski

    Primers for loading 7.62x39 to prevent slamfires?

    So, for reloading the 7.62x39, what primers do you suggest to decrease risk of slamfire in an AKM? CCI #34 military? Any Magnum large rifle primer? Current concern is an IO Inc AKM rifle with a floating firing pin.
  6. S

    Issue with Lee Ram Swage

    I recently pitched the Lee Ram Swage primarily for .308 and .223 reloading. I set the swage up for .308. I sized and deprimed my brass. When I use the swage it bends my case mouth inwards a significant amount causing me to have to re-size all the brass. Additionally, on cases with a significant...
  7. watermonger

    Primer setback after firing (with no powder load or bullet)

    I just reamed a LPP pocket on a single piece of 10mm brass down to an LRP with a pocket reamer, I wanted to see if my Glocks striker would be potent enough to set off these CCI magnum LRP's and after loading the empty casing with just the primer and dropping it into the chamber it fired but I...
  8. S

    No 10 or 11 Caps as Pistol Primers?

    Ok...we all expect (hope) supply shortage will end and Uncle Joe will be unsuccessful in blocking our right to have fun on the range and in the woods. So large pistol primers (and all the other kinds) should be cheap and available again. But, people used to say the supply of 12 ga would never...
  9. CavalierLeif

    Lost Small Pistol Primer Pocket

    Lost the small pistol primer pocket for my .38/.357 seating die. Anyone know if I can get a replacement without buying a new die set? Many thanks, Leif
  10. BMood

    First time reloading, Primer went off in the press

    Hi everyone, so I just started reloading and after working some brass I tried to seat a few primers tonight. It was my first time, and honestly I think I made a mess of things... I’m using a Lee breach lock challenger and I was priming on the ram. I have once fired (by me) federal .223 brass and...
  11. E

    3 Flash Holes? Doesn't appear to be drilled-out Berdan

    Hello, I'm relatively new to reloading rifle brass, though I've seen what 'normal' (2-hole) Berdan cases look like. I often pick up other cases from my local range while policing my own (and TBH, I pick up un-collected brass as a hobby). I came across a few 7.62x39 cases that have a ͶK 1982...
  12. Snidely70431

    Primer Ignition Device - Replaces Nipple

    This article is excerpted from the book, The Muzzle Loading Cap Lock Rifle by Ned H. Roberts. The entire book can be accessed here: https://babel.hathitrust.org/cgi/pt?id=umn.31951000799864f;view=1up;seq=7;size=175 Early in the 1880's in their efforts to improve the long range accuracy of...
  13. Load Master

    Sellier & Bellot Large Rifle Primer for .308 Win Update

    NOTE: This is just for information and in no way is it a suggestion for use. Communication with Sellier & Bellot has been slow due to Holidays and vacations this time of year. A few weeks back I supplied S&B with details of my load data, measurements and photos. Their conclusion, if I were...
  14. Load Master

    .308 AR - Wrong Primer - Blew Firing Pin Out of Bolt Carrier

    I learned something new about Sellier & Bellot primers. Their large rifle primer comes in two different flavors. There is the 5.3 LR and 5.3 LR-SE. S&B's usage chart shows the LR-SE is needed for .308 Win. I'm sad to say I proved them correct at my latest range day. No major damage, but it put a...
  15. V

    How to identify boxer and berdan primers

    I need help, could you identify the type of the primer here ? This is the inside of a bullet. This is the outside
  16. Load Master

    Do You Use Primer - Bullet Sealer?

    Anyone here use primer sealer on your rifle cartridges? What procedure do you use for sealing?
  17. B

    Primer goes off in inertial bullet puller on a loaded cartrige

    Primer goes off in inertial bullet puller on a loaded 22-250. Just had a close call when using a RCBS inertial bullet puller. I have been using one of these for about 30 years with out any problem. Today I was going to pull a few bullets out of loaded 22-250 ammo to change the load for...
  18. 3

    HELP! .40 S&W Dimpled primers

    Hey Guys. Need some help with my .40 loads. The problem I am running into is about a 10% failure to fire due to primers not igniting. I have tried exchanging every component I am using including using both CCI and Remington Primers; Power Pistol, IMR and Winchester powders; as well as both new...
  19. E

    Does anyone have experience using Dillon RF 100 primer tube loader?

    how reliable is it? how frequent is required maintenance and what needs to be done how many primer tubes have you loaded with it? how much time required to change small <-> large primer? Thanks!
  20. Toprudder

    Quick and easy primer size swap on Dillon 550

    Was playing around with my 550 press, trying to figure an easier way to swap between primer sizes. I think I succeeded. I searched and could not find this method online anywhere. Maybe someone else figured this out, but they did not post a video that I can find. I timed this, and the complete...
Back
Top