Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

1911 stuck firing pin

Discussion in 'Gunsmithing and Repairs' started by ffg, Mar 20, 2013.

Thread Status:
Not open for further replies.
  1. ffg

    ffg Member

    Joined:
    Mar 28, 2003
    Messages:
    28
    Location:
    Gardnerville,Nv
    Springfield 1911 GI. Primer has put a dent in the breech face and closed up the firing pin hole. This has happened 3 times in different configurations. The latest is with a new Caspian slide after maybe 200 rounds. The first two times were with the original springfield slide. SA repaired it once with a bushing but after the second time I replaced the slide. Normal loads are 200gr LSWC 5gr bullseye. I also have shot a lot of walmart winchester white box also.
    In its current form the frame is still SA but it has a wilson barrel, Wolffe springs, Caspian slide, Cylinder and slide hammer / sear / disconector. EGW (.202) slide stop and wilson barrel link. Ed Brown pin set. Had a local gunsmith install / fit the barrel to the new slide and generally check things out but now I'm right back where I started (but with a stack on receipts). Ideas?
    Thanks, Brian
     
  2. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    Must be awfully soft steel. The original USGI pistols weren't heat treated, and the (likely) 3000 Series steel was dead soft*...and the breech faces didn't peen and deform that badly for 8,000-10,000 rounds.

    Are you sure it's not primer flow into the port? That would suggest a headspace problem. How do the primers look?


    *Dead soft being defined as the hardness of the steel in its raw, unhardened state.
     
  3. Blue68f100

    Blue68f100 Member

    Joined:
    May 25, 2011
    Messages:
    3,004
    Location:
    Piney Woods of East Texas
    Caspen uses 9mm/38 FP in there slides. Do you have the right FP and did you check to see if the hole the correct size?
     
  4. ffg

    ffg Member

    Joined:
    Mar 28, 2003
    Messages:
    28
    Location:
    Gardnerville,Nv
    The pin is .065 and the firing pin hole was .069. I checked with gauge pins because I wanted to see the difference with my springfield pin (.071). The dent in the face is the diameter of the primer and a few thou deep. It looks like I took a .500 dia ball bearing, set it on the breech and smacked it with a hammer. Closed up on the firing pin like a collet.
     
  5. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Any chance you have been shooting lead-free / clean-range type ammo?

    Breach face peening like that was a known problem with lead-free primers when they first came out with it.

    I have never heard of such a thing otherwise on a 1911, or any other decent gun.

    To have it happen 3 times with two different slides is just a real wonderment!

    rc
     
  6. ffg

    ffg Member

    Joined:
    Mar 28, 2003
    Messages:
    28
    Location:
    Gardnerville,Nv
    This pistol has approx 5000 rounds thru it, pretty much all 200 LSWC with either bullseye, unique or w231 and Winchester LP primers. The 'issues' seem to have started when I installed a EGW slide stop with a pin dia .203. This was with stock SA barrel and slide. Within 200 rounds the pin was clamped down. I have shot these loads in my other 1911s but not nearly as many.

    (edit) the stock slide stop pin size is .195
     
    Last edited: Mar 21, 2013
  7. JRH6856

    JRH6856 Member

    Joined:
    Dec 5, 2011
    Messages:
    3,828
    Location:
    Flower Mound, TX
    Have you considered going back to the original slide stop?
     
  8. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,566
    It did happen, though not that quickly, with the original M1911. That is why Colt (sometime in the 1930's, IIRC) went to a hardened steel bushing threaded into the slide, and kept it until they went to a hard slide post-WWII.

    Jim
     
  9. BBBBill

    BBBBill Member

    Joined:
    Mar 7, 2005
    Messages:
    1,836
    Location:
    Alabama and Florida
    I've owned 1911s for almost 50 years and worked on them for nearly 35. Can't imagine how a slide stop could cause or even contribute to that problem.
     
  10. JRH6856

    JRH6856 Member

    Joined:
    Dec 5, 2011
    Messages:
    3,828
    Location:
    Flower Mound, TX
    Me either, but going back to the original slide stop would be one way of confirming or eliminating it as a factor. If it is indeed a factor, it would be interesting to know why.
     
  11. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,566
    I am sure that the link was changed at the same time as the slide stop (true, ffg?) so I wonder if somehow a too short/long link could cause that problem. I don't see how, but maybe something to kick around a bit.

    Jim
     
  12. ffg

    ffg Member

    Joined:
    Mar 28, 2003
    Messages:
    28
    Location:
    Gardnerville,Nv
    The original slide stop is in the gun now. I'm going to back off the load a bit and see what happens. This gun has a gremlin in it somewhere. When I first bought it, it would but brass in my forehead. Lowered the port a bit, extended ejector and new extractor fixed that. The next to last or last round would push feed. New mags and springs took care of that. Next was accuracy. Fitted a bushing and the slide stop tightened up the barrel. Now the firing pin episode...
    I Will find it...
    Thanks!
    Brian
     
  13. ffg

    ffg Member

    Joined:
    Mar 28, 2003
    Messages:
    28
    Location:
    Gardnerville,Nv
    No, I didn't change the link when I changed the slide stop. Holes in frame are .204, link was .204-.2045. The old stop pin was .195. Just thought I would take up the slack. Yes, probably the barrel was riding the link. But I got rid of the slop that allowed the barrel to push down and the accuracy improved. But in the end the patient died.:eek:
    But it was revived...
     
  14. BBBBill

    BBBBill Member

    Joined:
    Mar 7, 2005
    Messages:
    1,836
    Location:
    Alabama and Florida
    Well, your slide stop hole is out of spec at .204". Spec is .201" with .203" being max allowable. The .203" SS is a good fix for that. Not entirely necessary for it to be that large, but the .0005" - .00075" clearance should help alleviate any peening wear on the hole as long as the frame is properly hardened (which ain't very hard). The stock SS pin is under spec diameter. Spec is .200" with .198" being minimum. That means that an in spec gun will have anywhere from .0005" min - .0025" max clearance (half the difference in hole and pin diameters). You have .0045" clearance with the stock SS. Not good for accuracy or longevity IMO. I did have one SA 1911 years ago that egged out the SS hole. SA replaced it at no cost. Never another problem. What is your load? How old are your cases? How loose are the primer pockets?
    Perhaps the firing pin channel was drilled too deep, leaving insufficient material around the hole behind the breach face. Spec calls for .250" from the breach face to the back of the clearance channel for the tip. Perhaps a cerrosafe cast is in order. The only other thing I can think of would be to check the slide for proper heat treat.
     
  15. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    But twice with the orginial Springfield slide.

    And then again the third time with a new Caspian slide?

    It defies logic.

    rc
     
  16. JRH6856

    JRH6856 Member

    Joined:
    Dec 5, 2011
    Messages:
    3,828
    Location:
    Flower Mound, TX
    You have changed slides, and say you currently have a Wilson barrel which suggests you changed barrels. I can't tell from your posts; did the problem occurr with the original barrel or only with the Wilson?
     
  17. ffg

    ffg Member

    Joined:
    Mar 28, 2003
    Messages:
    28
    Location:
    Gardnerville,Nv
    This was a SA GI. Pretty loosey goosey.
    First time was stock barrel, slide and frame.
    Second time was stock slide, frame and wilson barrel.
    Third was time was stock frame, Caspian slide and wilson barrel.
    The only thing common is frame, oversize slide stop, and my ammo.
    I did finally buy a Chrony and scale check weight set. I have always just used the calibration set that came with the scale.
     
  18. JRH6856

    JRH6856 Member

    Joined:
    Dec 5, 2011
    Messages:
    3,828
    Location:
    Flower Mound, TX
    The load you describe, (200gr LSWC over 5gr Bullseye) is one I have shot for years in several different 1911s with no problems. So I doubt it is that load. Or the Unique or 231 loads if they are that conservative as well.

    So that leaves the frame and slide stop as common factors. Right now I'm leaning towards the frame being out of spec in more ways than one. but the easiest to test is the the slide stop. Go back to the original but don't reduce your loads. Try to change only one variable at time.
     
  19. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Nothing to do with the frame, or slide stop, or link, or pin hole location, or barrel, or chamber can cause primer breech-face peening on two different slides or one slide with a factory FP hole insert repair, plus another new slide of a different manufacture..

    Again, It defies logic or reasoning of anything I have seen in 50 years of 1911 fiddling & diddling.

    rc
     
  20. JRH6856

    JRH6856 Member

    Joined:
    Dec 5, 2011
    Messages:
    3,828
    Location:
    Flower Mound, TX
    I agree. And I agree with your preceding observation. But...gotta start somewhere and it beats staying stuck on " can't happen" when something apparently did happen.

    Maybe back to Tuner's question: are we sure we have eliminated primer flow instead of peening? What if the depression around the pin hole isn't peening but gas erosion from gas leaking around the primer?
     
  21. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Have we eliminated primer leaks or pierced primers and breech face erosion instead of peening??

    No we haven't.

    PS: Oops! Typing while your were posting!

    rc
     
  22. JRH6856

    JRH6856 Member

    Joined:
    Dec 5, 2011
    Messages:
    3,828
    Location:
    Flower Mound, TX
    Great minds and all that. ;)
     
  23. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,566
    Well "pierced" primers should be evident and ffg didn't mention that. They are the result of too light a firing pin blow so the primer is not sufficiently supported by the firing pin and flows back into the hole. I have seen that a number of times (and deliberately created it) but I never saw it cause any kind of a dent as described.

    And I don't see erosion causing the slide metal to clamp down on the firing pin; erosion would eat metal away, not peen it down.

    Jim
     
  24. ffg

    ffg Member

    Joined:
    Mar 28, 2003
    Messages:
    28
    Location:
    Gardnerville,Nv
    No erosion evident after SA repair and on new slide although there was a bit on the original slide.
    No pierced primers, primers look normal other than a nice little bump where it fills out the dent. The Caspian slide has a raised firing pin hole so the dent is centered. On the springfield slide the dent is like an eyebrow over the firing pin hole.
    I'll try to get some reasonable pictures in the morning.
    I use a pretty strong main spring to get a good trigger with the cylinder and slide hammer / sear / disconnector. So I'm pretty sure I have a solid hit on the firing pin.
    Looked at the tag that came with the Caspian slide and the hardness is RC-40.
    Just keeps gettin better and better...
     
  25. JRH6856

    JRH6856 Member

    Joined:
    Dec 5, 2011
    Messages:
    3,828
    Location:
    Flower Mound, TX
    Well, ffg, so far it seems that, except for you, we are all pretty well agreed that it can't be happening. :rolleyes:

    Yes! pictures please. The more detailed the better.
     
Thread Status:
Not open for further replies.

Share This Page