Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

.223 Failure to Eject-round stuck in chamber

Discussion in 'Gunsmithing and Repairs' started by Damn the Man, Jun 11, 2007.

Thread Status:
Not open for further replies.
  1. Damn the Man

    Damn the Man Member

    Joined:
    Apr 30, 2007
    Messages:
    40
    Location:
    Middle 'Merica
    Howdy. After feeding my new RRA Ar-15 a case of Black Hills, I bought the last and only case of .223 in my local shop: Wolf. :eek: After on 30 round mag, I reloaded and started into the second when the weirdest failure happened. Basically the bolt was open with a round jammed trying to feed. I cleared it and upon closer inspection there was the previous round still in the chamber. Now it's stuck in there.

    I've only tried sticking a cleaning rod down the pipe and tapping on it with a rubber mallet. I don't know what to do. HELP. :what:
     
  2. Powderman

    Powderman Member

    Joined:
    Dec 25, 2002
    Messages:
    1,626
    Location:
    Washington State
    1. Clear the weapon, of course.
    2. You did say that this is a fired case, right? De-mate the upper from the lower, and remove the bolt carrier group.
    3. Sit the upper receiver group, barrel up, on something that will absorb oil. Now, get yourself a can of Kano Kroil, and squirt a good amount down the bore.

    4. Let it sit overnight.
    5. Procure a wooden dowel (preferable) or part of a coated rod. Place it down the bore until it enters the case. Now tap the end with a hammer until the case ejects.

    6. Closely inspect the case. Is the rim intact? If so, you need an extra power extractor spring, and a extractor spring buffer. If the rim has been torn off, take the upper to someone who can do a detailed inspection of the chamber.
     
  3. Damn the Man

    Damn the Man Member

    Joined:
    Apr 30, 2007
    Messages:
    40
    Location:
    Middle 'Merica
    The round did fire, which is why the bolt blew back and the next round tried to feed and was jammed up between it and the bolt. I can see the rim is dented from that round trying to feed. I'll inspect it once I get it out.

    I took the bolt carrier out and ran a cleaning round down there and tapped on it. It didn't move. Is it likely bulged in there? I hope I didn't do anything bad to the barrel.

    Can I get Kano Kroil at Sportsman's Warehouse, or maybe a hardware store? Is that a special oil, or are there others that would work that I might already have lying around?
     
  4. Powderman

    Powderman Member

    Joined:
    Dec 25, 2002
    Messages:
    1,626
    Location:
    Washington State
    Kroil is probably the best penetrating oil in existence. You can read the specs--and find more goodies--at:

    www.kanolaboratories.com

    I don't believe that the case is bulged--more than likely, the cause might be twofold:

    a. Some of the older Wolf ammo had lacquered cases. When the weapon ran hot, this lacquer would gum up the chamber, making feeding and extraction difficult.

    b. An extractor with a weak buffer and spring might jump the rim of the case, instead of extracting it.

    In any case, the Kroil treatment should help. After giving it time to penetrate, I would probably get a coated rod, put it down the bore inside the case, cover the end of the rod with a block of wood and give the wood a good whack.Hopefully, this will extract the case.

    Kroil is available at the bigger hardware stores (Lowe's and Home Depot), and also from Brownell's.
     
  5. eliphalet

    eliphalet Member

    Joined:
    Apr 16, 2007
    Messages:
    1,682
    Location:
    Idaho
    .

    My guess ( only a guess) is lacquer gum is the problem with the stuck case, but your answer Powdernam gives me a question.
    If not lacquer what is Wolf using on steel cases now?
     
  6. DogBonz

    DogBonz Member

    Joined:
    Sep 23, 2006
    Messages:
    2,068
    Location:
    NJ
    Check your Extractor

    I have seen cases where shooting Wolf steel cased crap will nick or break the ejector.
     
  7. Powderman

    Powderman Member

    Joined:
    Dec 25, 2002
    Messages:
    1,626
    Location:
    Washington State
    I don't know the coating, but it hasn't given me any problems. 1000 rounds combined, through my Armalite/Oly Arms frankengun, and a Colt 6920. Zero problems.
     
  8. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,566
    DO NOT TRY TO USE A WOODEN ROD TO DRIVE OUT A STUCK CASE OR A STUCK BULLET!!!!! EVER!!! THIS MEANS YOU!!!

    The wood rod will splinter and then you will have a stuck case and a stuck and splintered wood rod. Obtain a good steel or brass rod and the case should come out. The main question then should be why the case stuck in the first place. That can go back to the chamber (rough?), the case material (brass too soft?) or case coating. The chamber should be carefully examined also. It is not impossible that defective chambering or even bad barrel material has left a chamber wider at the front than at the rear.

    Jim
     
  9. MudPuppy

    MudPuppy Member

    Joined:
    Jan 11, 2005
    Messages:
    1,529
    Location:
    UK and Texas
    Are the extractors really that fragile? How often have you seen that happen?

    What was the round count when that happen and do you know the mfg of that part?

    I can see maybe the coating gumming up and causing some stickiness that might cause this, but if you're breaking extractors willy nilly every time you use wolf, I'd be interested in hearing more about that.
     
  10. mrmeval

    mrmeval Member

    Joined:
    Oct 2, 2004
    Messages:
    1,768
    Location:
    Greenwood, Indiana
    The latest Wolf military classic cases are polymer coated, unknown polymer.
    The seem to function fine and I've not seen that particular failure with it.

    Isn't there some sort of fix using a o-ring for poor extraction on the AR-15?
     
  11. MudPuppy

    MudPuppy Member

    Joined:
    Jan 11, 2005
    Messages:
    1,529
    Location:
    UK and Texas
    The old extractors used to be very finicky, there's been a couple of PIP for those depending on type, I think (indicated by color of the ring and spring?)

    edit to add:
    Courtesy of Jeff White (and PS Magazine) The black insert is used to identify the new STRONGER extractor spring. Its really the spring that is different, the insert color was changed so you could ID it at a glance. Spring and Insert are purchased as a pair. The new spring was developed to solve some extraction issues of the M4. It is stiffer to provide more gripping force. Orginally only used on the M4 it is now authorized to be used on all M16s (instead of the older blue insert/spring).

    Update: While the black insert was used to ID the new stronger spring (silver colored spring) the insert itself was also stiffer. In addition in 1993 the Army switched to a gold colored spring (stronger still) with the black insert.
     
  12. Damn the Man

    Damn the Man Member

    Joined:
    Apr 30, 2007
    Messages:
    40
    Location:
    Middle 'Merica
    Hey Powderman, the rim was torn clear off the casing. Great advice. I got that oil this morning and let it sit all day. I put a coated cleaning rod down it and hammered on it three times and it let go.

    So the extractor tore the rim of the casing off. I've given everything I could a thorough cleaning and all seems fine. Should I disassemble the extractor? I never have. Will there be any flying springs? You said to take it to someone to look it over, but what's that a symptom of?
     
  13. Onmilo

    Onmilo Member

    Joined:
    Jul 26, 2004
    Messages:
    9,773
    Location:
    Illinois`
    Now get that cleaning rod and get rid of all traces of the Kroil oil.
    That stuff is well known to etch metal if left in place too long.
    I am pretty sure it won't affect the chrome plating in an M16 bore but don't be the first to find out it does.
     
  14. Powderman

    Powderman Member

    Joined:
    Dec 25, 2002
    Messages:
    1,626
    Location:
    Washington State
    DTM, it's good that the case came out.

    For some reason, the case was gripping the walls WAY too tightly, and did not release after the chamber pressure had loosened. What you're looking for is any abmormality that would cause the case to stick--rough chamber, etc.

    However, I believe that it would have manifested itself long ago, especially with a chromed chamber.

    Clean it up well, and take it to a gunsmith, if you wish. If not--or someone with a borescope is not available, clean well and take it to the range with good brass cased ammunition. Hopefully, it will work well.

    Onmilo, when did Kroil etch your bores or chamber? I use it to clean and loosen fouling in a benchrest gun, my M1A NM, and my precision rifle for duty use. I haven't had any problems yet.
     
  15. agony

    agony Member

    Joined:
    Dec 25, 2002
    Messages:
    539
    Location:
    WV
    Hi guys.
    Sadly, the same exact thing happened to me this weekend during a carbine class. I shot 1000 rounds of Wolf 'polymer' coated 223 through my AR, and had 5 cases stick in the chamber. 4 of them were fairly easy to remove with a little coaxing from a cleaning rod and some light tapping.

    However, the last round of fire included 5 30-round mag dumps rapid fire, and the second to last round did the same thing....stuck spent case in the chamber. The gun was smoking hot, and we tried hammering it out and it would not budge. Today, I used a coated rod to try whacking it out, and it still won't move, in fact I destroyed the rod.

    I'll have to try the Kroil, but I'm now worried about this 'etching' issue.
    Any word on that yet?

    Would any generic penetrating oil work too (liquid wrench, etc)?
     
  16. Powderman

    Powderman Member

    Joined:
    Dec 25, 2002
    Messages:
    1,626
    Location:
    Washington State
    The penetrating oil should work--after all, the size of the joint you have to access with the oil is not that small.

    IMHO, the consequences should NOT include an etched chamber--unless you have some super hard gunk trapped between the case wall and the chamber.

    Also, once you get the case out, remember to give your entire bolt carrier group a good dunking in a good solvent, like Hoppe's. When cleaning, pay close attention to the chamber and lugs. I would also probably give the chamber and bore a good going over with Sweet's, too. Just remember to neutralize the Sweet's solvent before continuing the cleaning cycle.

    I neutralize the Sweet's solvent like so:

    First, patch the bore about 5 times with dry patches. Next, run some oil patches down the bore, then remove all excess with the dry patches. Continue cleaning as normal. Remember to never mix solvents--they can sometimes react unfavorably.
     
  17. agony

    agony Member

    Joined:
    Dec 25, 2002
    Messages:
    539
    Location:
    WV
    Thanks Powederman!

    The etching comment with Kroil still kinda bugs me. Wonder if there is any truth in this. I've used Kroil for everything and I don't think I've had an issue yet.
     
  18. Onmilo

    Onmilo Member

    Joined:
    Jul 26, 2004
    Messages:
    9,773
    Location:
    Illinois`
    I work night shift at a large manufacturing plant.

    We use Kroil oil all the time for loosening bolts on CNC machining station fixture tables and a hundred other jobs requiring a high grade, high quality penetrating oil.

    What we have seen that if Kroil is allowed to sit for a prolonged period on time on metal surfaces, especially highly polished metal surfaces it tends to etch into the metal.
    Not to a great and huge degree, at least not for the amount of time we have allowed it to sit, but etch the metal it does.

    This caused enough problem with a robot raceway that was lubricated with a very large amount Kroil that a portion of the track had to be replaced because the robot would skip out of control alignment and stop moving.

    It has etched CNC machining center table slots enough that new securing blocks had to be fabricated to ensure the fixtures were precisely aligned with the cutting spindles.
    We are talking runout caused by etching of .050 to .100 microns.
    In the real world this isn't much, but to a machining center it is enough to put parts in the realm of out of specification tolerence.

    The etching probably wouldn't be noticeable to the average shooter especially since the amount of Kroil oil use in firearm applications is quite small.
    However if precision is your shooting game my warning about removing the penetrating oil after it has done it's job I would recommend heeding.

    This Manufacturer continues to use Kroil, it is a good product, but operating procedures now require it be removed from surfaces after use.
    It is not to be used as a lubricating oil, there are other products available for that purpose.
     
  19. Powderman

    Powderman Member

    Joined:
    Dec 25, 2002
    Messages:
    1,626
    Location:
    Washington State
    With regard to firearms, Onmilo is spot on with his post.

    Kroil is NOT a lubricant. It is a penetrating oil, and works great as a cleaner--especially to loosen fouling. But it is not a lubricant, and will not protect metal.

    However, (and this is to Onmilo) do you see a blend of Kroil and another product harmful? I also use Microil (from Kano Laboratories) on my guns. Specifically, I mix 1 part Kroil to 5 parts Microil. I have used it as a lubricant for about a year now, and have noted no ill effects. Any insight on this?
     
  20. W.E.G.

    W.E.G. Member

    Joined:
    Sep 26, 2006
    Messages:
    7,362
    Location:
    all over Virginia
    I've had Wolf cases stick in two different AR-type rifles.

    Gun fires.

    Extractor rips rim off case.

    Case stays stuck in chamber.

    I've had it happen with the lacquer-kote and the poly-kote wolf.

    [​IMG]

    Not all AR-type rifles do this. But, many do it occasionally, and some do it constantly. Wolf ammo is just that way. Some love it (because it works in their rifles) and others hate it - for obvious reasons.

    You don't need to do the Kroil deal to get the case out. I've always been able to just knock it out with steel cleaning rod. My WASR-3 just loves Wolf .223 ammo in any flavor.

    I won't say I'll never buy any more wolf .223. But, given any reasonable alternative, I woud stay away from it. I do know I'll never stick it in my AR's again.
     
  21. agony

    agony Member

    Joined:
    Dec 25, 2002
    Messages:
    539
    Location:
    WV
    W.E.G.,
    I finally got the case out. I tried freezing the complete upper in order to cause the steel case to contract, but that didn't work. I ended up soaking it in liquid wrench penetrating oil (didn't have enough Kroil to stick down the barrel). I banged on the case with a brass rod I bought at lowes--only because I bent two cleaning rods trying to get it out earlier. It worked. The case was covered with black melted polymer, or possibly hardened carbon fouling from the space between the chamber and the poorly expanded steel case.

    My rim also had that tell-tale extractor 'rip'.
    My chamber is also covered in that black stuff too. Very difficult to get out, and I'm considering taking a dremel to it. I did read elsewhere that single-firing some brass cased stuff through it will help to remove the the black stuff by transfering it to the brass case.

    I'll post the results later.
     
  22. Powderman

    Powderman Member

    Joined:
    Dec 25, 2002
    Messages:
    1,626
    Location:
    Washington State

    Nooooooooooooooo!!!!!!!!!!!!!!!!!! A thousand times, NOOOOOO!!!!!

    No fast moving machine tools around that chamber. Here's some help:

    1. Fully disassemble the rifle.
    2. Apply some Sweet's 7.62 solvent liberally. Do it outside if you can--the other residents of your household will not like the smell of cat pee permeating the home. Let it sit for about 10 to 15 minutes.
    3. Re-apply some more Sweet's.
    4. Take a chamber brush--a gen-you-wine M16 chamber brush. Install it on two or three sections of cleaning rod.
    5. Chuck the whole thing into a 3/8ths VSR drill.
    6. Barely start the brush into the chamber, then start the drill, running at slow speed. Work it gently into and out of the chamber a few times.
    7. Remove, and dry patch. Repeat as needed.

    When you get this crud out, liberally apply oiled patched to the chamber and bore. This is to neutralize the Sweet's solvent. Now, do a regular cleaning with Hoppe's or the solvent of your choice.
     
  23. agony

    agony Member

    Joined:
    Dec 25, 2002
    Messages:
    539
    Location:
    WV
    Thanks for the warning, powderman.
    I was only half-serious about the Dremel. But it's the serious half that would've done bad things to my rifle.
    :)
     
  24. Onmilo

    Onmilo Member

    Joined:
    Jul 26, 2004
    Messages:
    9,773
    Location:
    Illinois`
    powderman, I don't know if I can answer that question or not.,

    The robot tracks were supposedly cleaned and degreased before the Kroil oil was put down,,,,but I wasn't there.

    The machine pallets probably had a mixture of water and a Mobiloil synthetic coolant oil still on the surface metal prior to the Kroil being added.
    Again I don't know if this affected anything or not.

    I know the Company has sent out warnings about the proper use of Kroil Oil and I AM SURE people follow those warnings to the letter:rolleyes:
    So far nobody has lost their job for trashing anything.
     
  25. Bottom Gun

    Bottom Gun Member

    Joined:
    Dec 26, 2002
    Messages:
    766
    Location:
    Elgin, Arizona
    I have shot thousands of rounds of Wolf in my AR's and never had a problem until now.

    I just had the very same thing happen with a case sticking in the chamber. The rim of the brass looked exactly like the ones in the photos shown in W.E.G.'s post. It was the new style grey color Wolf. The primer was extruded somewhat and there was a slight crater around the firing pin dimple like the pressure might have been excessive.

    I wonder if this is part of a bad lot of Wolf ammo?
     
Thread Status:
Not open for further replies.

Share This Page