Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

.223 question

Discussion in 'Handloading and Reloading' started by dmrodco, Apr 30, 2007.

Thread Status:
Not open for further replies.
  1. dmrodco

    dmrodco Member

    Joined:
    Mar 21, 2007
    Messages:
    63
    Location:
    Utah
    I am looking to load up some 55gr vmax for use in my mod 70 and AR please suggest a good powder. I have used bl(c)2 @ 26.5 grns in the past with good results just looking to see if there is anything better.
    thanks in advance
     
  2. ARGarrison

    ARGarrison Member

    Joined:
    Dec 24, 2002
    Messages:
    304
    Location:
    Indiana, USA
    dm,

    I've used H335 in the past and going to give TAC a try in short order, new AR needs feed. I've used 40gr V-max in the past, but will have to go for a heavier V-max bullet for the 1/9 twist of my AR, if I go that way. Looking at loading up heavy match bullets right now.
     
  3. stormspotter

    stormspotter Member

    Joined:
    Jun 11, 2004
    Messages:
    423
    Location:
    Missouri
    223 question

    I have had good luck with BL-C(2) in my 10FP and CZ 527 Kevlar. The 10FP has a long throat and I am seating the Sierra 80 gr. Match out to 2.475. I could seat it .010 longer, but I want a snug fit, with the flat side of the bullet base even with the bottom of the neck. The boattail sits in the shoulder area. If I seat it longer the boattail in in the neck area and does not give full support to the bullet. ( Does this make sense to anyone?)

    The 10FP shoots the Sierra 65 thru 80 grains well and the CZ shoots the 65 thru 77 grains well. The 80's will not fit in the CZ's mag and I do not want to seat them that deep.

    Going to try reloading some of Sierras 77 gr., with the cannelure, for my Bushmaster V-Match using 24.5 grains of BL-C(2).
     
  4. distra

    distra Member

    Joined:
    Dec 3, 2005
    Messages:
    1,799
    Location:
    IA
  5. layusn1

    layusn1 Member

    Joined:
    Oct 7, 2006
    Messages:
    405
    My RRA AR15 gives me dime sized 5 shot groups with 27.4gr W748, 52gr Speer FMJBTHP Match bullets, CCI 450 Small Rifle Magnum Primers, FC cases, OAL 2.200. Works well for that weight with my 1:9 twist.
     
  6. Idano

    Idano Member

    Joined:
    Oct 2, 2006
    Messages:
    933
    layusn1,

    What is the length of your barrel in your AR 16", 20", or 24"? Also have you chronographed your loads and if so what is their velocity? I have an excellent load that turns out 1.5 or better in every AR with a 20" barrel with a 1 in 9 twist we have tested, but it is with Data Powder 2200 which you can't get anymore . So I am in the same boat as dmrodco and need to find something else for a 55 gr bullet. Here is my current load:

    Powder: 23.0 grains of Data Powder 2200
    Bullet: 55 gr Nosler BT or Remington/Winchester 55 gr SP
    Primmer: CCI-400
    Velocity: 2980 fps
     
  7. dmrodco

    dmrodco Member

    Joined:
    Mar 21, 2007
    Messages:
    63
    Location:
    Utah
    I havent crono'd the load yet however the BL(C)2 load gives me dime size patterns at 100yrds out of my mod 70 with no signes of excessive case pressure. Also the 26.5 gr is in the middle of the min and max powder charge. My ar's range in barrel size 2 each @16" 1 @ 20" and 1@ 24"
     
  8. Idano

    Idano Member

    Joined:
    Oct 2, 2006
    Messages:
    933
    dmrodco,

    Thanks for the information I may buy a pound of BL-C(2) and give it a try and see what kind of loads I can work up. I hope to get close in performance to what I have now. Until this thread I was leaning toward Accurate 2230 based upon, powder type, burn rate, recorded chamber pressures, and charge weight. However, I see that from your post that you are already experiencing about the same results with BL-C(2) as I am with DP2200 in different length AR barrels which inspires me to evaluate it first. - Thank you.
     
  9. tikkat3

    tikkat3 Member

    Joined:
    Sep 7, 2006
    Messages:
    56
    25.3gr H335 works well for me with 55gr V-MAX.
     
  10. layusn1

    layusn1 Member

    Joined:
    Oct 7, 2006
    Messages:
    405
    I have a 16" barrel. I don't own a chronograph so I couldn't tell you the velocity. I decided to try 3 different Speer bullets so I bought some 52gr flat base, PITA to get started in the case BTW, and 55gr FMJ. I loaded them up but haven't taken them out to the range yet, maybe this Sunday. Saturday just got taken up with the Special Olympics...those are always fun to work with so the bullets can wait a day.
     
  11. MDW GUNS

    MDW GUNS Member

    Joined:
    Mar 6, 2004
    Messages:
    381
    Location:
    Maine USA
    I use WIN 748 28 grain.
     
  12. CrackerJim

    CrackerJim Member

    Joined:
    Jan 11, 2006
    Messages:
    106
    Location:
    SW Florida
    I also like 748. I get good results at the range and it meters well.

    I don't recall group size offhand as it's been a while since I worked up my load. I have a Savage bolt rifle with a modest Bushnell scope. We plink golf balls on the 200yrd berm, plenty accurate as long as the shooter holds still :D .

    Jim
     
  13. Oohrah

    Oohrah Member

    Joined:
    Dec 29, 2006
    Messages:
    727
    Location:
    So. Coast Oregon
    Use 4198 with 55gr in my Ruger Mini 14 with good results:D
     
  14. dcloco

    dcloco Member

    Joined:
    Jan 31, 2006
    Messages:
    319
    If you end up going to a heavier bullet, I HIGHLY recommend H4895. With 69 gr HPBT Nosler or Sierra's, Win/Fed/LC cases, Fed 205M primer, I receive 3000 fps with ANY signs of pressure from my Savage 12FV. Have tried several other powders with the same combo, but only yield in the 27-2800 range.

    I use 24.8-25.0 grains of H4895 in this combination.
     
Thread Status:
Not open for further replies.

Share This Page