Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

.45 specifics

Discussion in 'Handloading and Reloading' started by SEVENPOINT, Oct 1, 2005.

Thread Status:
Not open for further replies.
  1. SEVENPOINT

    SEVENPOINT Member

    Joined:
    Feb 7, 2005
    Messages:
    21
    Location:
    Heck
    I went to the store today and snagged some reloading supplies. 1k federal "gold medal" match large pistol primers, some Winchester .45 auto cases, and some bullseye powder. Are there any loads that cater to these specific brands? Any help would be appreciated.
     
  2. lee n. field

    lee n. field Member

    Joined:
    Dec 29, 2002
    Messages:
    3,730
    Got any particular bullet in mind?
     
  3. Smokey Joe

    Smokey Joe Member

    Joined:
    Jan 2, 2003
    Messages:
    2,617
    Bullseye powder

    Sevenpoint--Bullseye works with every .45ACP bullet in Lyman's Cast Bullet Handbook; the same in Lyman's 48th ed. Reloading Handbook. In some instances it is listed as the most accurate of the powders tested for that particular load and bullet.

    Do you not have a reloading manual? (Preferably more than one; cross-referencing is always good!) If not may I humbly but earnestly suggest that you get one or more.

    IMHO, there is nothing to beat having the recipie in front of you in black and white, published by one of the major manufacturers, to check and re-check as you go about setting up your loading.

    Forgive me, fellow THR'ers, but anybody can post anything on the internet, and that doesn't prove it is tested or safe.

    Call me an old mother hen if you will, but I have never Ka-Boomed a gun, and intend to keep it that way. Doing so tends to ruin the entire afternoon.
     
  4. The Bushmaster

    The Bushmaster Member

    Joined:
    Jan 29, 2005
    Messages:
    7,837
    Location:
    Ava, Missouri
    Pornstar? O K (chuckle ;) ) I assume that you have a loading manual. Bullseye is a very versitile powder. I think it can be loaded into most any calibre. Check your load manual and have a ball... :)The Lyman #48 that Smokey Joe mentioned is a very good start to an extensive library.... :scrutiny:
     
  5. HSMITH

    HSMITH Member

    Joined:
    Dec 26, 2002
    Messages:
    4,933
    If you are looking for extreme accuracy the Hornady XTP bullets have been really good for me.
     
  6. SEVENPOINT

    SEVENPOINT Member

    Joined:
    Feb 7, 2005
    Messages:
    21
    Location:
    Heck
    Thanks for the replies guys. The only manuals I have are the ones that came with the reloading kit I bought. I guess I need to pick one up. Better safe than sorry right? Thanks again.
     
  7. JoeG52

    JoeG52 Member

    Joined:
    Jan 31, 2005
    Messages:
    104
    Location:
    SE Pennsylvania
  8. JDGray

    JDGray Member

    Joined:
    Sep 16, 2005
    Messages:
    5,129
    Location:
    SW MI.
    Rainier bullets are very accurate and affordable 230 rn $29.99/500 JDGray
     
  9. rborensr

    rborensr Member

    Joined:
    Sep 14, 2005
    Messages:
    59
    Smokey Joe, I aggree with ya 100%.
     
  10. LHB1

    LHB1 Member

    Joined:
    Feb 7, 2005
    Messages:
    873
    Location:
    Houston
    I would strongly recommend buying/reading a loading manual and choosing your load BEFORE buying components. Some stores will not exchange reloading components.

    Good shooting and be safe.
    LB
     
  11. ClarkEMyers

    ClarkEMyers Member

    Joined:
    Oct 3, 2003
    Messages:
    931
    Location:
    A stone's throw from Henry's Fork
    I've found the H&G/Saeco 130 in front of 3.5 BE to work any case and primer

    I've found the H&G/Saeco 130 in front of 3.5 BE to work any case and primer but I completely agree with earler comments that loads developed in a lab are always to be preferred. Few of us test different powder positions and temperatures or use any kind of pressure gun be it lead units of pressure or pisa.

    On the other hand 2.7 BE with a 148 wadcutter and 3.5 BE with a .45 wadcutter are such classic loads that I even trust my memory and I know they've been used millions of times.
     
  12. RugerOldArmy

    RugerOldArmy Member

    Joined:
    Sep 18, 2004
    Messages:
    750
    ClarkEMeyers,

    I think he specified .45 Auto...kind of supporting Smokey Joe's point.
     
  13. ClarkEMyers

    ClarkEMyers Member

    Joined:
    Oct 3, 2003
    Messages:
    931
    Location:
    A stone's throw from Henry's Fork
    Yes of course he did and I knew that. My point was

    Yes of course he did and I knew that. My point was that there are a very few loads that have passed from experience into folklore - and in the days when Lyman was associating pet loads with people in their manuals and Gil Hebard was quoting favorite loads of the winners everybody knew about the 2.7 BE for centerfire (.38 special) and 3.5 BE for .45 gallery pistol and once you get beyond those few it's time for the manuals. The same could be said about the Hensley and Gibbs #68 and some BE up to about 5 grains for action shooting to stick to .45. The mention of .38 Special was to give an additional example of a load so common that everybody knew it once upon a time. Obviously nothing to do with the listed cases and interest.

    Ed Matunas in particular but Dave Andrews and others have occasionally written about the lengths they had to go to in order to validate the loading manuals they put their names on. None of us is likely to do that, not having our time and expenses paid so that loads beyond the manuals may well have some weakness - Bluedot loads may show odd temperature effects that never showed up for the guy who lives in Florida - the point is to be careful taking somebody's load fired someplace you don't live in a gun you don't own and not checking it against the book.

    My bad for not specifically saying that a 148 grain wadcutter is commonly associated with a .38 Special target load and the #130 bullet is a nominal 185 grain semi-wadcutter and the famous #68 at about 200 grains has a sharp shoulder but fits the lines of 230 grain ball and so loaded that the edge of the meplat is tangent to the curve of the ogive on the 230 grain ball then the #68 will feed very reliably in guns that may not in those days have been modified for wadcutters. Notice that the current sort of stepped down feed in newer Colt 1911's will feed a wider variety of bullets more reliably.
     
Thread Status:
Not open for further replies.

Share This Page