Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

45ACP and the crimp. Most bullets are tight, a few are not. Why?

Discussion in 'Handloading and Reloading' started by Skydivermn, Jul 8, 2011.

Thread Status:
Not open for further replies.
  1. Skydivermn

    Skydivermn Member

    Joined:
    Feb 7, 2011
    Messages:
    6
    I'm confused about how much crimp I should put on my .45ACP. I'm currently using a 3 die RCBS kit (resize/deprime, bell, seat/crimp), and have been guilty of crimping the living shizzle outta the case, all the way to putting almost nothing on it and having the bullet get pushed into the case when loading into the magazine. I've improved upon my crimping, but I'm still unsure about why a small number of my cartridges have a bullet that will spin/push into the case.

    Let me explain what happened last time I was reloading. Looking at my Lyman #49 reloading manual (printed in 2008), it says that the case mouth should be .473 (I think these numbers are accurate, they're from memory). To me, that means basically increase crimp until you're at that number. When loading up a few boxes on my RCBS Rock Chucker, I had 2 cartridges that would still allow me to rotate the bullet in the case. All 98 others appeared to be tight (but not too tight where plated bullet is all wrinkled at the case mouth) and ready to go, all very near .471 measurement. I know that all my cases were run through the sizing and depriming die, but I'm not sure why these fit the bullet differently. Shouldn't all cases be brought back into a valid size with resizing? Or are these cases perhaps just past their useful life? If this is the case (no pun intended!), there's nothing that can be done? Also, do I crimp to .473 or is my slightly tighter crimp no big deal? Is there some acceptable range of crimp? I'm using a Glock21 with both factory and Lone Wolf barrels. My rounds are mostly 5.7gr W231 with 200gr plated lead flat nose out of the 5" barrel. My rounds usually go BOOOM, so I'm doing enough things correctly, but am I missing something obvious? Thanks for your help!

    SkydiverMN
    :banghead:
     
  2. Fishslayer

    Fishslayer Member

    Joined:
    Jan 1, 2010
    Messages:
    1,974
    Location:
    People's Republik
    Are you sorting headstamps? Different headstamps have different thickness brass.

    RP is notoriously thin. I only use it for .452 cast bullets.
    TZZ goes right in the trash.

    PMC seems to be the thickest. I use that for my XTP anti-zombie loads. ;)

    Sometimes overcrimping can be bad.

    Are you using a taper crimp die?
     
  3. dmazur

    dmazur Member

    Joined:
    Apr 28, 2007
    Messages:
    2,263
    Location:
    Pacific NW
    Well, I've only loaded a few thousand .45ACP rounds and I'm far from an expert.

    What I believe to be true is -

    1. Tension is provided by resizing and not by crimp. (Magnum revolver cartridges and slow powders can require a very heavy roll crimp to prevent bullet pull and provide proper burn, but the .45ACP doesn't fall into that category.)

    2. For .45ACP the correct crimp is not much of a crimp at all, but is just the removal of the "bell" that is created by the powder-thru die (or similar die for single stage reloaders.) This is usually described as a taper crimp and the correct profile isn't much different from a straight line.

    3. Theoretically, the .45ACP headspaces on the case mouth, so you don't want to "bury" the case mouth in the bullet. Many reloaders do this to some degree or another anyway, with good results, as many pistols control headspace with the extractor. However, it isn't typical practice. I believe your 0.471" diameter at the case mouth is correct.

    4. Removal of the bell is most easily done by a separate taper crimp die, but it can be done (carefully) with a combination taper crimp/seater die and one operation if it is set up correctly.

    5. Some cases just have thinner case walls than others. I believe Remington is the usual culprit, but I'm not sure. These can be a real problem, as the ID after resizing just may not be small enough to develop the proper tension.
    (If you have only a few of these and they can be sorted out, sometimes the easiest solution is to just toss them...)

    6. Bullet diameter has to be correct and consistent. Some manufacturers occasionally make a few that are undersized.

    In other words, loose bullets can be caused by bad components, or bad setup, or both. Trying to track it down is kind of like a murder mystery, and can take some patience. :)
     
  4. Steve in PA

    Steve in PA Member

    Joined:
    Dec 29, 2002
    Messages:
    2,574
    Location:
    NE PA
    I've been reloading the .45acp for several years now. After my initial set up, I have not touched my dies. I use the RCBS dies and seat/crimp in one step. I use mixed cases, (Rem, Speer, PMC, etc) and Rainier 230gr bullets. I cannot beging to tell you how many thousands of rounds I have reloaded, and have no problems like the OP.

    I agree, that it is either bad bullets or bad set up of dies.
     
  5. Fishslayer

    Fishslayer Member

    Joined:
    Jan 1, 2010
    Messages:
    1,974
    Location:
    People's Republik
    Is there such a thing as a taper crimp/seating die? I don't see how that would work. It certainly wouldn't for cast lead. My Lee seating die will definitely shave lead if I don't have it adjusted correctly. I get around that with the Taper Crimp. The seating die doesn't need to be so precise.

    While (according to other reloaders) the taper crimp isn't 100% necessary it sure makes life a lot easier. I wouldn't be without it.
     
  6. dmazur

    dmazur Member

    Joined:
    Apr 28, 2007
    Messages:
    2,263
    Location:
    Pacific NW
    Well, I think that particular animal has been hit several times in this thread -

    http://www.thehighroad.org/showthread.php?t=601809

    And here's one made by RCBS -

    RCBS 45ACP Taper Crimp Seater

    I use a separate taper crimp die myself, but there are some who want to do this in one step even if it is problematic. (Lately, it seems to be related to the number of stations on a Hornady LNL AP... :) )
     
  7. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,901
    Location:
    Alabama
    Yep, RP is thin, and some sizers that work fine with other brass will not size RP enough. Please send all TZZ brass to me. It is IMI brass.

    Yes, there is such a thing as a .45 ACP seater crimper which uses a taper crimp. It is what reloaders used for decades to load millions of rounds of .45 ACP ammo. RCBS and Reddding still make them. Lyman too I believe.

    I has become popular to crimp in a second step even in applications where it doesn't have to be. Folks posting wrongly about how hard it is to do doesn't help. Neck tension holds the bullet. All you need is a slight taper crimp. Just enough to remove the bell, or at most .002 crimp. Easy peasey. :)
     
  8. 243winxb

    243winxb Member

    Joined:
    Jul 7, 2004
    Messages:
    9,393
    Location:
    Hopewell Big Woods
    After FL sizing, no expander, is the bullet tight in the case? If loose, brass wall thickness is thin, or you need a FL die that sizes more. Measure your expander, it should be .450" or slightly smaller. If larger than .450" turn it down to smaller.
     
  9. gregj

    gregj Member

    Joined:
    Sep 9, 2008
    Messages:
    387
    Location:
    N. Va.
    As others have mentioned, look at your brass. Look at the headstamp for those rounds with a loose bullet, and those that are tight, and I bet you will see a difference.

    The crimp measurement given in the manual is the max spec, not what your gun will like. A crimp of .469 - .470 seems to work for me for mixed headstamp brass, and I've used the exact load in my 1911s.
     
  10. Skydivermn

    Skydivermn Member

    Joined:
    Feb 7, 2011
    Messages:
    6
    thanks for the help, learned a bunch!

    Thanks gregj, that's a good point. For my Glock21 .471 loads fine, but I also have a Lone Wolf barrel being delivered and I'll need to check and see what'll work best for that.

    Thanks everyone for their responses, I appreciate the info and I'll check the headstamp for the loose ones.

    :cool:
     
  11. GooseGestapo

    GooseGestapo Member

    Joined:
    Jan 6, 2003
    Messages:
    3,395
    Location:
    W.GA
    I think something else is afoot.

    He mentioned that he's using "plated" bullets.

    I've seen some plated bullets where they didn't cull the "culls" and some under plated, meaning under sized bullets got through the q-c personnel.

    With most brass and my "cast" bullets, I've not seen the issue with "loose" bullets unless the bullet was defective. Even with Remington or A-merc brass. I don't use my .45's for competition so I don't segregate the brass. I've even got some mil-spec brass thats got 1918 head stamps so I expect it's rather "experienced" brass at that......

    I suspect an "under plated" bullet that's not full diameter. The bullets are plated in an electro-plating tank and the bullets might not have gotten full current or proper solution and got inadequate deposition of alloy.

    Aren't using "Berry" bullets by chance are you ????? Hint, hint~!!!!
     
    Last edited: Jul 9, 2011
  12. thump_rrr

    thump_rrr Member

    Joined:
    Nov 7, 2010
    Messages:
    803
    Location:
    The North Country
    I'm a little fussy when it comes to reloading or shall I say that my 1911 is a little fussy as to what it likes to be fed.

    I've only been shooting and reloading for less than 5 months now.

    I've already reloaded and shot over 4,000 rounds of .45 ACP.

    I've never purchased a single manufactured round of .45 ACP.

    I began using the Lee Deluxe Pistol Four Die Set so I was seating and crimping in separate stages but I was still getting jams on the first round of a fresh magazine quite often.

    It was suggested to me to sort my brass by headstamp and not to crimp brass which didin't require it. This helped reduce the frequency of jams by 50%.

    I recently switched to a Hornady LnL AP Progressive presswhich doesn't have enough stations to factory crimpso I started using a Dillon case gauge to check my rounds.

    Any rounds that don't drop freely into the case gauge get run through the Lee Factory Crimp Die which has the crimp ring backed off. This allows pos sizing.
     
  13. 918v

    918v Member

    Joined:
    Mar 16, 2006
    Messages:
    3,931
    Try seating and crimping in two separate steps.
     
  14. brickeyee

    brickeyee Member

    Joined:
    Feb 25, 2005
    Messages:
    3,135
    Especially important with lead or platted bullets, not so critical with jacketed.

    I always remove the bell in a separate step for any bullet.

    Crimp is not the main thing holding the bullet, the interference fit between the correctly sized shall and the larger bullet diameter stretches the brass to provide most of the tension.
     
  15. sean eady

    sean eady Member

    Joined:
    Jun 23, 2011
    Messages:
    122
    First post , so hello to all..... I just got into reloading and am still figuring things out myself. I also use the RCBS 3 die sets on a single stage rock chucker. I have recently had issues with my 9mm cases and was told to try seating and crimping as seperate steps and picked up a Lee Factory crimp die. To make a long story short it did indeed take care of the 9mm case issues and I immediatly purchased one for all of the pistol calibers I reload. Yes it adds 1 more step , but well worth the end result .... Try one out for your 45's very easy to adjust and gives a perfect crimp (or bell removal) by following the instructions that come with the die.
     
    Last edited: Jul 9, 2011
  16. Hobie

    Hobie Member

    Joined:
    Feb 16, 2005
    Messages:
    366
    Location:
    Staunton, VA
    While it is true that brass from different makers has different dimensions in such as case mouth thickness and thus inside diameter it is also true that brass, even from the same lot, may be of differing elasticity or ductility. IOW, you can size it and it won't stay at the smaller diameter OR when you shoot it it is too brittle and it cracks. Annealing MIGHT help but I find that usually, when brass that was previously ok won't get a good grip on a bullet it is best to simply chuck it into the recycle can. One also has to accept that one has to use reason and logic to determine exactly what the problem is with the brass at hand.
     
  17. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    I've only run across two cases that wouldn't hold neck tension and that was recently, almost 30 yrs. since starting to reload.
    If a case is properely resized, the bullet should not be able to be moved at all without the use of a puller. Try seating the bullet without a crimp and I'll bet you can't mve the bullet at all. If that holds true then your problem is how your applying the crimp, not the brass.
    This is not to say some cartridges don't need a crimp, some do because of their application. The rule of thumb is to apply the least amount of crimp necessary to prevent bullet jump. Start by measuring the OAL and shoot all but the last round, and then measure it to see if it changed OAL. If it did change increase the crimp a little bit more until you've stopped it from moving. Over crimping can actually cause you to loose neck tension by buckling or collasping the the case.
     
  18. 1SOW

    1SOW Member

    Joined:
    Oct 28, 2007
    Messages:
    4,108
    Location:
    South Texas
    As said: The crimp doesn't retain the bullet, the sizing does.
    The crimp is to remove the belling of the mouth when seating the bullet. If it feeds reliably it's good-to-go.
     
  19. Lothar Allen

    Lothar Allen Member

    Joined:
    May 3, 2009
    Messages:
    26
    remember that crimp is case length dependent.
     
  20. dmazur

    dmazur Member

    Joined:
    Apr 28, 2007
    Messages:
    2,263
    Location:
    Pacific NW
    I've found a separate taper crimp die is fairly tolerant of variations in case length.

    After all, it is just removing the bell, not trying to "roll over" the case mouth a precise amount.
     
  21. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,901
    Location:
    Alabama
    Yep, a proper taper crimp is very tolerant of case length, and, as posted, we are using very little "crimp".
     
  22. rscalzo

    rscalzo Member

    Joined:
    Jun 6, 2005
    Messages:
    860
    Location:
    Epping, NH
    I found them decent. In fact, just loaded up two hundred for a xsteel match with no problems. Now if you're talking Americ, thet isn't worth the effort to throw out.
     
  23. brickeyee

    brickeyee Member

    Joined:
    Feb 25, 2005
    Messages:
    3,135
    I stil have over 10,000 TZ & TZZ .45 ACP shells, some on their 10th loading.

    There is nothing wrong with them.

    Both head stamps are Israeli Military Industries (IMI).
     
  24. Geckgo

    Geckgo Member

    Joined:
    Dec 14, 2010
    Messages:
    784
    Location:
    Southern Louisiana
    Got my rockchucker setup today (finally) and started playing with the 45ACP dies. I don't have my caliper yet, it's on back-order, I may just run down to Lowes tomorrow and get one if I get impatient. Anyways, when I got to the crimp/seat step I set up my die off of a loaded federal round and popped out a couple of blanks. When I get the caliper then I can check them for OAL and start putting powder and primers in, but I want the rest of the round set up propperly before I start making them hot. I've been very nervous about the crimp step and wondering if it's maybe too tight, too loose, etc. I can see a very slight necking on them, maybe only the last 1/16-1/8 of an inch, but the bullets are not moving with force applied. How important is crimp? I mean, my XD isn't going to blow up if they are a shade tight is it? Not too worried about them being loose at the moment, they've got plenty of tension.

    Added this here cause it's related and I didn't want to start a similar thread.
     
  25. dmazur

    dmazur Member

    Joined:
    Apr 28, 2007
    Messages:
    2,263
    Location:
    Pacific NW
    See post #18.
     
Thread Status:
Not open for further replies.

Share This Page