Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Adjustment question

Discussion in 'Rifle Country' started by blackops, Nov 15, 2009.

Thread Status:
Not open for further replies.
  1. blackops

    blackops Member

    Joined:
    Jun 6, 2009
    Messages:
    1,238
    If you have a 1/2 moa clicks, your target is 500yds, and your bullet drops 38 inches, how many clicks do you adjust your dial up?
     
  2. WNTFW

    WNTFW Member

    Joined:
    Jul 16, 2006
    Messages:
    1,906
    Using 1" per 100yd as 1 MOA
    15.2 clicks so you need 15 or 16 1/2 MOA clicks to correct 38 inches @500

    15 clicks = 37.5" (7.5 MOA x 5)
    16 clicks = 40" (8 MOA x 5)

    The other thing is MOA is really 1.047
    So 38 is 14.517 1/2 MOA clicks. Using true MOA or 7.25 MOA

    You made need to determine if the scope is true 1/2 MOA or 1/2" per 100yds. Scopes can also be a little off of either

    Just make sure 38" is the right number to correct for.
    It is easier to think in MOA than to think in the # of clicks. Figure what MOA you need then divide by click value or better yet use the MOA value if marked on the dial or turret.
     
    Last edited: Nov 15, 2009
  3. RonE

    RonE Member

    Joined:
    Aug 19, 2007
    Messages:
    696
    Location:
    Rockport, Texas
    For simplicity a minute of angle is 1" at 100 yards and 5" at 500 yards so, a half minute of angle would be 1/2" at 100 or 2 1/2" at 500

    If you are 38" low at 500 yards you need to move up about 8 minutes of angle so about 16 clicks or 15 clicks as stated above.
     
  4. blackops

    blackops Member

    Joined:
    Jun 6, 2009
    Messages:
    1,238
    Thanks for the quick replys. Interesting...at my local range I make 18 click adjustments at 547 yds and I knock down the plates all day long. With a 1/2 moa dial each click at 500 is 2.5 inches. So that means at 550 I'm dropping 45inches then. Most charts I view show a drop at 500 of 38 inches. Seems mine is dropping a bit more.Later that same day I went shooting again, but with cheap wal-mart loads instead of my sierra hand loads. I made a 4 click adjustment with my range being 300. My bullet should drop around 6 inches, but I ended up being high. It worried me . lol I figured it was because I was originally zeroed with my hand loads so the cheap rounds were going to shoot different and obviously they did. I just didn’t think it would be that much.
     
  5. WNTFW

    WNTFW Member

    Joined:
    Jul 16, 2006
    Messages:
    1,906
    The 1st time I shot 600yd was in a match using a .308. I had heard many times 16 MOA is the standard come up for the .308 from a 100 to 600. I was actually applying pressure to trigger & waiting for the shot to happen when I realized I didn't add any elevation. I was still on a 100 yd zero. I managed to get off the trigger and not fire. I added 16 MOA and sure enough I was on paper.

    Ammo being different would be a good reason. BC of the bullets another. If you notice Sierra is the only company that list BC for bullets in 3 ranges of velocity. I am convinced handloading is a big factor in rifle accuracy.
     
    Last edited: Nov 15, 2009
  6. blackops

    blackops Member

    Joined:
    Jun 6, 2009
    Messages:
    1,238
    Yes, I have figured out hand loading makes a huge difference. For some people the difference probably doesn't mean that much, but I have developed OCD for accuracy and it never is enough for me. I guess that is a good thing and bad.
     
Thread Status:
Not open for further replies.

Share This Page