Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Almost a squib?

Discussion in 'Handloading and Reloading' started by popper, Jan 3, 2012.

Thread Status:
Not open for further replies.
  1. popper

    popper Member

    Joined:
    Nov 10, 2010
    Messages:
    975
    Shot 19 30-30 170 LC w/o GC, using unique. One FTF. Cocked and tried again. Just a click both times. Case looked just like a FTF. I didn't think anything of it till I tried to pull the bullet. Tore the nose off trying to get it out. Finally cut the case in half with pipe cutter. No powder, just carbon residue, mostly stuck to the bottom of the bullet and coating the inside of the case. Lubed with LLA/JPW and it had dried about a week before loading. Yes, I use a light to check the powder before I do anything else. Can that lube kill the powder and primer that easily?
     
  2. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Sound like it just did to me.

    rc
     
  3. Blue68f100

    Blue68f100 Member

    Joined:
    May 25, 2011
    Messages:
    3,385
    Location:
    Piney Woods of East Texas
    No powder, your lucky you didn't stick a bullet in the rifleing. Need to get a bullet puller so you don't damage your brass and bullets.

    A good reason to use a dry lube for the necks.
     
  4. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    I agree, no powder in the case.

    I thought when I replied the first time I saw where you said there was unburned powder stuck to the bullet lube.

    I just re-read it and see you said just carbon.

    That is a no powder squib for sure.
    The primer firing left the carbon on the bullet.

    rc
     
  5. 243winxb

    243winxb Member

    Joined:
    Jul 7, 2004
    Messages:
    9,318
    Location:
    Hopewell Big Woods
    Johnson Paste Wax has a flash point of 88 F degrees. The paraffin & carnauba might be ok, but how about the 85% isoparaffinic hydrocarbon? The base area of the bullet is small. The small amount of lube would not seem to be a problem. In fact over on cast Boolets, someone ask that very question. Is lube on the base of the bullet a problem? All said no, except me. I do not want any lube on the base of my cast bullets. But thats just me. I think you forgot the powder. Sorry. :)
     
  6. popper

    popper Member

    Joined:
    Nov 10, 2010
    Messages:
    975
    Bullet didn't even move in the case, made NO noise other than the hammer click. I wipe the GC when I use one, didn't have any on these. Guess I was lucky, no harm, no foul - just have to be more careful. I have bullet pullers but couldn't get this one out with vice-grip and the press - hard cast lead still tears. It didn't even have much of a crimp, just enough to remove the flare. I guess the temp and lube glued the bullet in, they usually just pull right out and I put them in the melt can.
     
  7. rsrocket1

    rsrocket1 Member

    Joined:
    May 20, 2010
    Messages:
    1,312
    Location:
    Sacramento, CA
    I wonder what the stuck projectile does to your case pressure if it is glued in that strongly. I hope you aren't loading these hot. Hopefully if you're using a load with Unique, you're just in the 5-10 grain ballpark.

    I've shot 158g lead bullets out of my 4" 357 at 231 fps with nothing more than a primer (not intentionally). Most of my squibs however involve the use of a brass rod and hammer which I always keep in my shooting bag.
     
  8. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    Get a new light!
     
Thread Status:
Not open for further replies.

Share This Page