Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Any reason to get separate Boresnakes for .22 rifle and pistol?

Discussion in 'General Gun Discussions' started by jblane, Jan 25, 2010.

Thread Status:
Not open for further replies.
  1. jblane

    jblane Member

    Joined:
    Dec 29, 2009
    Messages:
    52
    I'm new to guns and I just bought a rifle and pistol, both in .22lr, to start learning to shoot. I noticed that Boresnakes come in 2 different versions for .22, one for rifle and one for pistol. Is there any real difference between the two that would make it necessary to buy both? Or can I just use the rifle version for both guns?
     
  2. chevyforlife21

    chevyforlife21 Member

    Joined:
    Jul 12, 2009
    Messages:
    1,337
    Location:
    America
    only difference is that the rifle has a slightly longer brush and the entire snake is longer too, it will work for both. the reason for the pistol rope is its shorter for storage (not necessary)
     
  3. LemmyCaution

    LemmyCaution Member

    Joined:
    Jun 4, 2008
    Messages:
    890
    Just don't try to use the pistol snake on a rifle. The pull line will sometimes tear loose from the floss, leaving the floss in the bore with neither end accessible.
     
  4. jblane

    jblane Member

    Joined:
    Dec 29, 2009
    Messages:
    52
    Thanks, that clears it up. :D
     
  5. wally

    wally Member

    Joined:
    Jan 2, 2004
    Messages:
    12,749
    Location:
    Houston, Tx
    Yup, if you only want one, get the rifle. I've a lot of .22 pistols and .223 rifles so I have one of each. Not the best way to clean but better than nothing and lets me postpone a real cleaning for many more outings.

    --wally.
     
  6. Top_Gunn

    Top_Gunn Member

    Joined:
    Apr 8, 2007
    Messages:
    120
    Marlin's owner's manuals for their .22 rifles recommend not cleaning the bores. I don't clean rimfire bores ever: either for rifles or pistols.
     
  7. jblane

    jblane Member

    Joined:
    Dec 29, 2009
    Messages:
    52
    Well that's something to consider. The rifle is a Marlin too. It doesn't take too much to convince me NOT to do any kind of cleaning!
     
  8. dom1104

    dom1104 Member

    Joined:
    Aug 3, 2007
    Messages:
    1,366
    hmm. I wonder why NOT cleaning would be a good thing. I clean my 22lrs
     
  9. chevyforlife21

    chevyforlife21 Member

    Joined:
    Jul 12, 2009
    Messages:
    1,337
    Location:
    America
    alot of cleaning can damage the bore (think metal to metal contact) when you do clean the bore you dont realy need to use a brush same wear problem there. most important is oiling the bore so it doesnt rust. alot of guys clean .22s every 500 rounds or every few months what ever hapens first or so.im starting to do this. i have two marlins they have always been cleaned after even 1 shot. a .22 is a good gun to use a bore snake with. realy alls you have to worry about is oiling the bore. i put solvent on the front of a bore rope and oil at the very end pull it through 5 times and your done. sometimes you realy need a rod though anyway its good to have both. and i use a pistol bore snake for my 9mm carbine and its more then long enough. so a .22 pistol bore snake might work for you anyways
     
  10. boatme99

    boatme99 Member

    Joined:
    Jan 31, 2009
    Messages:
    99
    Location:
    Mid-Tn., land of shootin'!
    I've been shooting for quite a few years, and one thing I still don't understand: I'm cleaning a steel barrel with a SOFT brass brush. Methinks the brass is going to wear way before the bore.
    That said, I really don't use a brush very often. Clean with patch and oil is usually enough unless corrosive primers/ammo are involved.
     
  11. Kor

    Kor Member

    Joined:
    Dec 24, 2002
    Messages:
    774
    Location:
    Tucson, AZ
    ^ The brass bore brush is not the issue - it's allowing the steel cleaning rod to come into contact with the muzzle crown which can affect the accuracy of the gun. Again, toxicity = dosage - an occasional light scrape every now and then is not a big deal, but when guys obsessively scrub the bore like they're going to turn the gun over to a Drill Instructor for a white-glove inspection, that will take a toll.

    Another issue is that aluminum cleaning rods can get grit embedded in them, and if you have to push the rod through the bore with great force(e.g. pushing doubled-up cleaning patches) the rod can bow and cause bore abrasion mid-way down the barrel. Solution: wipe the rod clean between passes, and don't force it if it don't want to go.

    A final consideration is that rimfire priming compound often contains ground glass to improve the compound's sensitivity to firing-pin-impact - the glass dust causes extra friction within the priming compound, thereby making it more likely to ignite when crushed by the firing pin. Trace amounts of the glass may make it down the bore, which might cause additional abrasion if scrubbed back-and-forth too vigorously - it's also possible that a layer of deposited lubricant from the .22 bullets can keep the glass particles from contacting the bore.

    All in all, there's a lot of reasons to avoid scouring your .22LR's bore too frequently...
     
  12. MarkDozier

    MarkDozier Member.

    Joined:
    May 15, 2006
    Messages:
    375
    I use bore snake t run through my barrels a couple of times and then use patches to clean.
    And carbon-fiber cleaning rods are the bomb
     
Thread Status:
Not open for further replies.

Share This Page