Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Auto 5, Savage 745 problem

Discussion in 'Gunsmithing and Repairs' started by Dovebuster, Apr 5, 2008.

Thread Status:
Not open for further replies.
  1. Dovebuster

    Dovebuster Member

    Joined:
    Apr 5, 2008
    Messages:
    3
    Location:
    Suwanee, Georgia
    I have a Revelation 400 I am trying to refurbish a Revelation 400. (It' built on the Browning auto 5 and Savage 745 model). All metal and stock work is done and put back together.
    Now I load the tube with shell, pull the bolt back, release and the shell does not feed out of the tube.
    There is a small metal piece that holds the shell in. What is the name of this piece and does anyone have any idea what the problem may be?
    Thanks in advance
     
  2. Leadbutt

    Leadbutt Member

    Joined:
    Jan 3, 2003
    Messages:
    361
    Location:
    Tidewater,Virginia
    Sounds like the "Shell Stop" check with Numrick Parts they may have a diagram that shows it and parts needed
     
  3. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Did it work before you took it apart?

    rcmodel
     
  4. Dovebuster

    Dovebuster Member

    Joined:
    Apr 5, 2008
    Messages:
    3
    Location:
    Suwanee, Georgia
    ???

    Its a gun my brother gave to me. He says it shot good before I took it apart. I never shot it but I'm sure its something I have broken, or damaged as I did not break it down to that level.
     
  5. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Well about all I can offer from this distance is take it apart again and look for any obvious missing or misplaced parts, springs off or mis-aligned & binding, etc..

    Did you have to force anything to put it back together?
    (That's always a bad sign right there!)

    Here is an A-5 parts schematic.
    http://www.brownells.com/aspx/ns/schematics/schemmfg.aspx?schemid=404&m=2&mn=Browning®&model=Auto-5+

    Check part # 20 (Shell Latch) and part #21, (Shell Latch Spring).
    See if it is there, and not squished.

    rcmodel
     
  6. GeorgeR

    GeorgeR Member

    Joined:
    Dec 19, 2005
    Messages:
    231
    Location:
    Boca Raton, FL
    Shell Stop

    If its like the Auto 5, you may have put the magazine cut off in backwards (it can assemble both ways), but I'd first check the shell stop and the coil spring. Did it have those vertical screws in the edge of the receiver, or those pesky roll pins? They may not have gone back in all the way and the shell stop is binding.
     
  7. kirbythegunsmith

    kirbythegunsmith Member

    Joined:
    Nov 12, 2006
    Messages:
    205
    Location:
    St. Louis area
    Details

    You must remember that recoiling barrel semi guns need the barrel to stroke to feed shells from the magazine.
    These don't work like 1100's, etc.
    Feed the first shell into the chamber, close the bolt (with the safety already on), invert the gun, finish by loading the magazine.
    You may also have other problems, but even if all of the parts are perfect, you'll never get that gun to feed a shell from the tube by just pulling back the bolt.

    Once more, into the breech.

    kirbythegunsmith@hotmail.com
     
  8. Chawbaccer

    Chawbaccer Member

    Joined:
    Feb 3, 2005
    Messages:
    1,865
    kirby, every M11 I have owned would chamber a round from the magazine by operating the bolt.
     
  9. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    +1
    Same here.

    M-11's and A-5 Brownings feed any way you want them to feed. The barrel doesn't have to recoil except to make them operate semi-automatically.

    Mines setting empty with four rounds in the tube right now.
    All I have to do to load it is pull the bolt handle back and let it go.

    PS: The Winchester Model 11 is the only long-recoil shotgun I can think of that loaded by pulling the barrel back.

    It doesn't have a bolt handle though. :what:

    rcmodel
     
    Last edited: Apr 9, 2008
  10. Dovebuster

    Dovebuster Member

    Joined:
    Apr 5, 2008
    Messages:
    3
    Location:
    Suwanee, Georgia
    Thanks guys

    Hey thanks for the advice. Cycling the barrel by hand solved the problem. I don't know why or how but kirbythegunsmith solved this one. I have been around brownings all my life and did not know this trick.
     
  11. tphanson

    tphanson Member

    Joined:
    Sep 14, 2008
    Messages:
    1
    Savage 745

    I was just given a Savage Model 745, 12-gauge. Don't have much experience with shotguns, auto in particular. How do I use it, when I pull the action back it stays, is that normal? I assume it will take 3 shells, 2-3/4, I know that. How about slugs? What is the shotgun like? Any help would be great.
     
  12. Chawbaccer

    Chawbaccer Member

    Joined:
    Feb 3, 2005
    Messages:
    1,865
    It is normal for the bolt to lock back if there is no shell in the magazine. I don't know if the Savage had a three shot version or not, your magazine may be plugged back to two shells because of hunting regulations. Do a search for friction ring settings, maybe for the Rem 11. It is important for proper operation to have them set correctly. You can get replacement parts from Numrich.
     
Thread Status:
Not open for further replies.

Share This Page