Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Beretta 686 Silver Pigeon trigger assembly

Discussion in 'Gunsmithing and Repairs' started by Nickelplate, Jan 24, 2012.

Thread Status:
Not open for further replies.
  1. Nickelplate

    Nickelplate Member

    Joined:
    Sep 5, 2011
    Messages:
    28
    Location:
    Washington DC Area
    I would like to get into my trigger assembly to clean but there is a screw setup that I've never seen before. On the bottom of the receiver there is a small screw surrounded by a larger screw. Is anyone familiar with this? I expect to hear, "just leave that to a gunsmith." But I'd still like to clean it myself. Can anyone help?
     
  2. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Last edited: Jan 24, 2012
  3. Nickelplate

    Nickelplate Member

    Joined:
    Sep 5, 2011
    Messages:
    28
    Location:
    Washington DC Area
    Bingo! I think they're #55 and #78. Before I try this, can you tell me if there is a specific tool required? Are they reverse threads? What else can you tell me?
     
  4. Fleet

    Fleet Member

    Joined:
    Sep 20, 2010
    Messages:
    384
    Location:
    Oklahoma
    It's just as RC said, removing 78 will allow removal of 55. The only thing you'll need is a screwdriver that properly fits the screw slots so you don't bugger them up. Chances are good that 78 will be somewhat tight, and 55 may not be tight at all. Both should be RH thread.
    When you put it back together, be careful of the alignment of 55/78. 78 should seat within 55 easily, without resistance.
     
  5. oneounceload

    oneounceload member

    Joined:
    Apr 24, 2008
    Messages:
    15,710
    Location:
    Hot and Humid FL
    Which means hollow-ground gunsmith-type screwdrivers, not your typical Ace hardware ones. Removing the stock should give you ample room to spray a cleaner on there to blow any gunk out, then relube. Taking apart any trigger group can mean springs flying if you are not familiar with it. I know with SxS guns it is best to have the hammers cocked when removing the trigger groups; I am not sure if it applied to Beretta actions as well
     
  6. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    I would suggest unless you take your own clocks & watches apart to clean them, you do as oneounceload suggested.

    Just take the stock off and hose it out with spray cleaner, and then re-lube it.

    If you have a double gun like that with an inertia trigger that works though?
    Don't mess with it!

    O/U's don't get all that dirty inside the action.

    rc
     
  7. JohnBT

    JohnBT Member

    Joined:
    Dec 26, 2002
    Messages:
    13,232
    Location:
    Richmond, Virginia
  8. Nickelplate

    Nickelplate Member

    Joined:
    Sep 5, 2011
    Messages:
    28
    Location:
    Washington DC Area
    Thank you friends. I will likely not dive too deep. I've had a little experience with fly springs so I'll probably leave it to the professionals.
     
  9. Nickelplate

    Nickelplate Member

    Joined:
    Sep 5, 2011
    Messages:
    28
    Location:
    Washington DC Area
    I don't plan on dismantling the trigger assembly, I just want to clean as you suggest. I don't take my 870 express trigger apart either. Just spray, blow with compressed air, wipe, spray, wipe. Then clean the compartment and surrounding area.

    That is one narrow slit for the main screw. You folks were right. On my way to Midway USA...
     
  10. Fleet

    Fleet Member

    Joined:
    Sep 20, 2010
    Messages:
    384
    Location:
    Oklahoma
  11. Nickelplate

    Nickelplate Member

    Joined:
    Sep 5, 2011
    Messages:
    28
    Location:
    Washington DC Area
    Thanks for turning me on to the Brownells site. That looks to be a great store.
     
  12. John3921

    John3921 Member

    Joined:
    Feb 2, 2012
    Messages:
    483
    Location:
    Montana
    There is a discussion here of how to do some of this on the 68x series. Including which of the thin bits you need to pull the trigger group. To clean the triggers you don't need to pull those two screws - but if you need to drop the trigger group out of the receiver you will have to remove those two screws. - and the one hidden under the safety.

    http://www.shotgunworld.com/bbs/viewtopic.php?f=57&t=278811
     
Thread Status:
Not open for further replies.

Share This Page