Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Best Price for Uberti 1858 Remington C&B Cylinder?

Discussion in 'Blackpowder' started by alienbogey, Jan 21, 2011.

Thread Status:
Not open for further replies.
  1. alienbogey

    alienbogey Member

    Joined:
    Dec 23, 2009
    Messages:
    270
    I'm looking for a C&B cylinder, blued, for a Uberti 1858 Remington New Army in 44. The best price I have found on the net is Taylor's at $66 - anyone know of a better price somewhere?

    I'm willing to buy used also if anyone knows of one available; I posted a WTB in the classifieds.
     
  2. BHP FAN

    BHP FAN Member

    Joined:
    Sep 23, 2008
    Messages:
    5,810
    Location:
    Northern California
    nope, that's cheap for Uberti. I've seen them go for $100.00 elsewhere.
     
    Last edited: Jan 21, 2011
  3. junkman_01

    junkman_01 member

    Joined:
    Aug 7, 2009
    Messages:
    1,728
    Location:
    Florida
    Do you think a Pietta cylinder is going to work OK in the OP's Uberti?
     
  4. BHP FAN

    BHP FAN Member

    Joined:
    Sep 23, 2008
    Messages:
    5,810
    Location:
    Northern California
    CRUD! No thanks, Junkman...I'm going to fix that. I have swapped cylinders from make to make, but it's just the luck of the draw, and doesn't always work.
     
  5. BHP FAN

    BHP FAN Member

    Joined:
    Sep 23, 2008
    Messages:
    5,810
    Location:
    Northern California
    Thanks for spotting the error, J-man. fixed.
     
  6. BlackPowderSmoke

    BlackPowderSmoke Member

    Joined:
    Jun 9, 2010
    Messages:
    38
    Location:
    North Carolina
    alienbogey,
    I searched the web also looking for the best price for a 44 caliber c&b cylinber for an Uberti 1858 Remington New Army and Taylor's $66 price was the best I could find. Would love to find some used ones about half that price.
     
  7. arcticap

    arcticap Member

    Joined:
    Mar 20, 2005
    Messages:
    6,185
    Location:
    Central Connecticut
    That's really inexpensive compared to the price of a replacement Ruger Old Army cylinder, that is if there were any readily available.
    Spare Pietta cylinders aren't getting any less expensive either, and even some replacement semi-auto magazines cost more than that.
    Maybe their cost is somehow related to the price of [olive] oil in Italy................ in Euros of course. :D
     
    Last edited: Jan 22, 2011
  8. Oyeboten

    Oyeboten Member

    Joined:
    Mar 23, 2008
    Messages:
    3,696
    Good to know.


    I have been thinking of getting an extra Cylinder for my Uberti Remington.


    Do these usually jump right in?

    Or, do they tend to need some sort of fussing or fitting?

    And how would one 'fit' a spare Cylinder, anyway?
     
  9. BlackPowderSmoke

    BlackPowderSmoke Member

    Joined:
    Jun 9, 2010
    Messages:
    38
    Location:
    North Carolina
    I have two Uberti 1858 Remmies. I had trouble the first time I switched the cylinders.
    I had to fit my hand on one of my revs a bit to make the cylinder out of the other one work right. The cylinder failed to turn all the way on one chamber only. The cap was not under the hammer so it misfired everytime. Had to turn the cylinder by hand til it clicked to fire. I didn't pose a problem when firing the revolver's original cylinder and the clyinder out of the malfunctioning revolver worked perfectly in the other revolver.

    It was simple to fix once the source of the problem was determined. There was a bur on the hand. A nice polishing did the trick.
     
Thread Status:
Not open for further replies.

Share This Page