Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

bprevolver chambers

Discussion in 'Blackpowder' started by omarkw11@gmail.com, Jul 31, 2008.

Thread Status:
Not open for further replies.
  1. omarkw11@gmail.com

    omarkw11@gmail.com Member

    Joined:
    Jun 6, 2008
    Messages:
    30
    Location:
    crawford, co
    in a post i noticed someone mention chamfering the chambers. was wondering if anyone has done this and did it help accuracy/loading. i have a 51 navy replica that im getting good groups with but would like to do better. also has anyone polished the chambers and if so, did it help?:confused:
     
  2. Smokin_Gun

    Smokin_Gun Member

    Joined:
    May 10, 2005
    Messages:
    1,632
    Location:
    Mojave Desert, California
    Omark, polishing the chambers will not help your accuracy. Not recommeded as material removed from chamber will change diameter and therefore change ball size, ect.
    Chamfering is merely to make loading the balls easier. They would sit into a deeper recess before pressed onto powder. I would say to leave them as they are unless you are having trouble loading. Has nothing to do with increasing accuracy. More shooting is the best way to improve accuracy.

    Hope that helps, Happy shootin',

    SG
     
  3. mykeal

    mykeal Member

    Joined:
    Sep 9, 2006
    Messages:
    5,147
    Location:
    Michigan
    I would recommend you mike the chambers, the forcing cone and the lands and grooves of the barrel. It's possible (in fact, likely) that they don't match up, and reaming the chambers and forcing cone to within a couple thousandths oversize compared to the groove diameter will give you the most accurate combination possible.

    The easiest way to make those measurements is to force a .380 ball (assuming a .36 cal Navy) into a chamber, then push it out from the back (after removing the nipple); using a good set of mikes, measure across the flat surface swaged onto the ball. For the barrel bore, force the same size ball halfway down the barrel from the muzzle, then push it out from the back; you will have clearly swaged land and groove marks that can be measured. For the forcing cone, push the ball in just far enough to shave a ring of lead, then push it back out from the muzzle.
     
  4. Voodoochile

    Voodoochile Member

    Joined:
    Apr 2, 2008
    Messages:
    1,144
    Location:
    Central Virginia
    Mykeal, that is what I'm in the process of doing to one of my Pietta 58's.
    .4490 Grove diameter
    .4405 Lands diameter
    .446 - .4465 Chamber diameter

    I'm waiting for my custom .4510 Chamber Reamer from manson reamers so that I can do exactly what you mentioned.
     
  5. scrat

    scrat Member

    Joined:
    Jan 27, 2007
    Messages:
    6,882
    Location:
    Monrovia, CA
    wow thats some differences i imagine you make those chambers more closely to the others and your accuracy will improve imensily.
    keep me informed on this one i want to know.
     
  6. Voodoochile

    Voodoochile Member

    Joined:
    Apr 2, 2008
    Messages:
    1,144
    Location:
    Central Virginia
    Scrat this'll be my first time ever doing this on a C&B revolver & I've only done this to two other SAA revolvers to correct a chamber to bore dimentions issue, this piece shoots OK but not like I want & in reading about the Silver Moon issue which this piece has on 2 of the 3 cylinders I talked to Long Rifle & determined that reaming may cure it enough to bring the groups tighter.

    Took me some time to Slug the barrel with a .490 Ball so that I'll have plenty to get an accurate reading on "know that I could have used a .457 ball but wanted to be sure of my measurements.

    Oh & BTW that 51' Navy you got from me had better numbers than this 58' I'm working on.
     
  7. scrat

    scrat Member

    Joined:
    Jan 27, 2007
    Messages:
    6,882
    Location:
    Monrovia, CA
    That navy is an awesome shooter. Amazingly both my 51's are my best shooters. Especially the pietta. could not believe it. they last a long time and shoot more accurate than my others.
     
  8. omarkw11@gmail.com

    omarkw11@gmail.com Member

    Joined:
    Jun 6, 2008
    Messages:
    30
    Location:
    crawford, co
    thank you all for the ideas, much appreciated
     
Thread Status:
Not open for further replies.

Share This Page