Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Brass Trouble (Help Please)

Discussion in 'Handloading and Reloading' started by kis2, Apr 8, 2013.

Thread Status:
Not open for further replies.
  1. kis2

    kis2 Member

    Joined:
    Jun 16, 2006
    Messages:
    925
    Hi all,

    So I thought I had over pressure issues and was going to lighten the load a bit, but even without firing a complete cartridge or just using the brass from a fired cartridge I have the same issue. Here's the issue:

    Bolt on the 700 (308) cycles smoothly and lightly with snapcap or no round. With my current box of loads, I can put a round in, feed it forward with the bolt until there is some resistance, and then pushing the bolt handle down into position seems to move it the rest of the way forward (just a tiny amount).

    Extracting that round (whether fired or not) the bolt moves smoothly if a bit heavy until about the last 15% of its travel, where it takes a decent amount of efforct to finish the motion. almost pops as it passes over that point. bolt slides back and ejects the round fine.

    Brass is lapua on its 6th load, neck sized only after initial full length size.

    Hard to describe in type, apologies for the long description.

    Thoughts on this? Thanks for any help!
     
  2. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Zero- headspace from too many neck-sizing's.
    Time to FL size it again.

    It is so tight with zero headspace it is getting stuck in the chamber on closing the bolt.

    Then 'pops' loose when the primary extraction cam pry's it out on opening.

    rc
     
  3. kis2

    kis2 Member

    Joined:
    Jun 16, 2006
    Messages:
    925
    hey rcmodel, thanks for the reply.

    is this the, 'bumping the shoulder back' scenario I think I read about somewhere?

    And is there some kind of rule of thumb? Like every 5th load needs to be a FL size? Or is it just neck size the brass, see how it chambers, and if as above you FL size it?

    Thanks for the help
     
  4. jim243

    jim243 Member

    Joined:
    Sep 11, 2009
    Messages:
    1,992
    Yes it is.

    Jim
     
  5. esheato

    esheato Member

    Joined:
    Apr 8, 2003
    Messages:
    2,784
    Location:
    NoVa
    Nope, when the cases are getting tough to chamber, you either FL or bump the shoulder back...both achieve the same "improve case to chamber fit". Of course, one may be better than the other for your gun, and you'll have to figure that out by trying them.
     
  6. Innovative

    Innovative Member

    Joined:
    Oct 24, 2009
    Messages:
    286
    Location:
    Florida
    Try bumping the shoulder back - .001" (with a FL die) everytime you resize. That'll keep your handloads uniform, and they'll always chamber.

    There are no drawbacks to full length resizing, if it's done accurately.
     
  7. kis2

    kis2 Member

    Joined:
    Jun 16, 2006
    Messages:
    925
    forgive me guys, but I'm a bit confused.

    I have a FL die and a neck die. the neck sizer only effects the neck. the FL die will effect the entire case.

    How would I set up the FL die to only bump back the shoulder (if thats desireable over just FL sizing) and most importantly how can I get the most consistency over the life of the brass? right now it sounds like I need two loads, one for neck sizing, one for every five reloads when I have to resize the entire piece of brass. If I can do one load that's what I'd want.

    Thanks for the help!
     
  8. rsrocket1

    rsrocket1 Member

    Joined:
    May 20, 2010
    Messages:
    1,312
    Location:
    Sacramento, CA
    A cartridge headspace gauge would be very handy here. Measure the case that is tight, measure the headspace, screw down the sizing die so that the shoulder is bumped back a few mils, recheck and record that number.

    OR

    Simply use a "too big" case and set the appropriate sizing die depth by trial and error and mark that spot with a magic marker on the die and locknut in relation to an index spot on your press.

    For economy, if you want to also measure face to ogive lengths, get this set and just the .308 headspace gauge because you can't buy individual bullet comparators by themselves. No need to pay more for a bunch of headspace inserts you'll never use.

    After buying these, I find a magic marker, a set of calipers and the guns themselves as the best gauges.
     
  9. Innovative

    Innovative Member

    Joined:
    Oct 24, 2009
    Messages:
    286
    Location:
    Florida
    Keep it Simple ....

    Kis2 ........

    Just use a FL sizing die accurately, and it will resize the whole case in one operation (while fully supported). All you need to know is how much clearance your handloads have in YOUR particular chamber. Then set your die height to make perfect fitting handloads.

    COAD-06.jpg

    This gauge displays your exact shoulder clearance. It gets calibrated to one of your fired cases. Then, look at one of your handloads, and you'll see exactly how much to raise (or lower) your die height.

    It works on ALL different calibers - without any special attachments or bushings.
     
  10. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,390
    Location:
    Alabama
    You don't, it will also size the body a little, but no worries. Use some sort of gauge or method to log your shoulder location on the cases that are hard to chamber. They are slightly over the max your gun can accept freely. Then use that gauge etc to adjust the FL sizer so you only bump the shoulder back .001, .002, or max .003.

    Innovative Technologies
    sells of of the coolest, and reliable, tools to do this. I use home made gauges. There are a number of ways to do this. I have quit neck sizing everything except .22 Hornet. I use a standard FL die or a Redding Type S bushing style FL sizer. I do have a Forster bushing bump die that works well, and will bump the shoulder, but with it sooner or later you will still have to size the body.
     
  11. esheato

    esheato Member

    Joined:
    Apr 8, 2003
    Messages:
    2,784
    Location:
    NoVa
    This would work also:

    191549.jpg

    It's called a Redding Instant Indicator. It measures case length, bullet length (base to ogive) and headspace and OAL.

    Step 1: Measure the length of your difficult to chamber brass from base to datum on the shoulder using the gauge. Step 2: Use the FL or bump die to push the shoulder back a thou or two. Step 3: Use the gauge to see how much you're setting it back. Step 4: Check chamber fit. Step 5: Continue the loading process.
     
  12. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    A $250 dial indicator set-up will certainly work.

    However a simple L.E. Wilson case gage will work without Chinese Algebra.
    Or a $1.49 Magic Marker or Dry Erase marker.
    Or a .25 cent birthday cake candle.

    Any will work as well, if not better.

    1. Color or smoke the shoulder of a tight case.
    2. Chamber it.
    3. Where the marker ink or candle soot rubs off is tight.
    4. Adjust the FL sizing die down to bump the shoulder back until it isn't tight.

    IMO: I have never owned a rifle accurate enough to benefit from neck sizing only.
    (If the FL sizing die is adjusted to fit the rifle chamber this way.)

    rc
     
  13. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,390
    Location:
    Alabama
    Best to remove the firing pin and spring from the bolt if you go old school for better feel when trying the cases in your rifle.
     
  14. kis2

    kis2 Member

    Joined:
    Jun 16, 2006
    Messages:
    925
    Are you not losing case life by FL sizing over neck sizing? Or case volume? Or consistency? My rifle isn't a benchrest special 6mm, but it is all match graded.

    all I can think right now is 'why didn't I read something about this 3 years ago?'

    Thanks for the help everyone, I'm going to keep reviewing your posts until I can understand this.

    Ultimately, by whatever method, it seems like I can get my FL die set up in such a way where I can have 1 load.
     
  15. esheato

    esheato Member

    Joined:
    Apr 8, 2003
    Messages:
    2,784
    Location:
    NoVa
    Ahem...

    It's $120.99 RC. :p

    Of course, bumping the shoulder until it fits is all that is necessary...and smoking the shoulder is more than adequate, but if you want to measure, you need a gauge. Same result, varying paths and prices to get there.

    Absolutely. On my benchrest gun, I remove the firing pin. Place a bumped case in the chamber and let the bolt handle fall on the case...if I did it right, it closes half to 3/4 of the way with a "crush fit" the last bit ensuring a perfect chamber fit.

    There is a wrong way and a right way to set up a FL die...unfortunately, both will let you chamber and shoot the cartridge. The wrong way overworks the brass because the die is set up incorrectly. The right way sizes it enough without overdoing it.

    For my LR gun, I buy once fired brass. FL size it and shoot it in my gun. Plinking load or whatever I have surplus components for. Once it's formed to my gun, I neck, load, neck, load, etc. When the bolt gets difficult to close, I bump the shoulder using a Redding shoulder bump die, which I previously used a Redding Instant Indicator to set up for proper 1-2 thou bump, then load as usual......starting with a neck sizing die.
     
  16. MEHavey

    MEHavey Member

    Joined:
    Jul 27, 2010
    Messages:
    2,378
    Location:
    virginia
    Other than a caliper, you need one thing and one thing only:
    Hornady Headspace Gauge Set

    You've already got some oversize (i.e, hard-to-chamber) cases, so....

    1. Screw the sizing die to contact the shellholder and back off 1/4 turn.

    2. Size a case and see if it will chamber without effort (we hope not)

    3. Screw the sizing down another 1/16 turn and try again

    4. And again 1/16 turn*** ... (sooner or later the bolt will close without significant feel and/or you will contact the shellholder)**

    5. Use the Hornady guage to meaure the case's "headspace" dimension at that point and write it down. THAT is your target from now on... for any/all cases from whatever source, in that rifle.

    NOTE: You may have to set up your sizing die slightly differently for different brass having different "springback" (See note below) -- but the headspace measure you established in Step 5 always stays the same.


    ** If you have to, go 1/16 turn beyond contact. I have to do that for my 30-06 Winchester brass. On the other hand, my Lapua brass requires shellholder contact only.

    *** If you're really anal, go 1/32 turn. :neener:
     
    Last edited: Apr 8, 2013
  17. NeuseRvrRat

    NeuseRvrRat Member

    Joined:
    Jan 24, 2011
    Messages:
    2,098
    Location:
    Wilmington, NC
    guffey will be along soon with some feeler gauges to sort this out for you
     
  18. Innovative

    Innovative Member

    Joined:
    Oct 24, 2009
    Messages:
    286
    Location:
    Florida
    Kis2 .....

    As you can see there are a jillion different techniques for measuring chamber clearance. Some are a bit primative, and others are more refined. (I'm not sure which items cost as much as shown.)

    The Digital Headspace Gauge can also measure the bullet jump to your rifling. Again, this tool requires no special attachments, and it works on ALL different calibers. Very simple to operate.
     
  19. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Not enough to matter if your rifle works right!

    Right?? :D

    IMO: Case life is meaningless to me.
    New brass is cheaper then a new glass eye when an over the hill case lets go.

    rc
     
  20. murf

    murf Member

    Joined:
    Nov 16, 2010
    Messages:
    3,193
    Location:
    arizona
    size like rc said in post #12.

    save one of the sized cases for next time, so you don't have to go through all that again. just put the case in the press, run the ram up to the top, screw the sizing die down to touch the case, and get to sizing. save that case again for the next time.

    murf
     
  21. Arkansas Paul

    Arkansas Paul Member

    Joined:
    Mar 18, 2009
    Messages:
    7,401
    Location:
    Central Arkansas
    Not to mention, vision is much better without the glass eye too. :evil:
     
  22. Innovative

    Innovative Member

    Joined:
    Oct 24, 2009
    Messages:
    286
    Location:
    Florida
    After you accurately Measure your actual chamber clearance, then you can see how well other methods really work.
     
  23. ironworkerwill

    ironworkerwill Member

    Joined:
    Jan 3, 2013
    Messages:
    1,839
    Location:
    AUabama- WE FEAR NO WEEVIL
    FWIW I'm going to neck size untill I have to FL. Then, I'm going to use a marker to mark that shoulder. Then, I'm gonna do it all over again. Because it is cheap, primitave, and fun. And I AM a cheap AND primative kinda guy! NEENER!
     
  24. kis2

    kis2 Member

    Joined:
    Jun 16, 2006
    Messages:
    925
    Thanks for everybody who helped out. I've got a game plan and am moving forward.

    Thanks again!
     
  25. kis2

    kis2 Member

    Joined:
    Jun 16, 2006
    Messages:
    925
    Gents,

    Including today, I've shot twice since November. I am very rusty. Nonetheless, my groups today (in order of appearance) were a .8, .5 and .5, with zero brass issues.

    Thanks to all who helped, I think we've got success.
     
Thread Status:
Not open for further replies.

Share This Page