Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Bullet Overstabilization?

Discussion in 'General Gun Discussions' started by Matt304, Aug 26, 2008.

Thread Status:
Not open for further replies.
  1. Matt304

    Matt304 Member

    Joined:
    Sep 19, 2006
    Messages:
    624
    Location:
    Utica, IL
    I know that a bullet will not stabilize and shoot accurately from a twist rate which is too slow.

    But what about a twist rate which is a little fast for the bullet weights used, will this cause accuracy problems?

    I am having a bench pistol barrel made for a .30 caliber cartridge firing light rifle bullets under 140 grains. Recommended twist is 1:12". I was thinking that if someday I decide I want to re-chamber that barrel for .308 with heavier bullets, maybe I should start with a faster twist, like 1:11 or even 1:10. I however don't want to use the faster twist if I will sacrifice accuracy at lighter weights like 135gr.

    Thanks
     
  2. DoubleTapDrew

    DoubleTapDrew Member

    Joined:
    Feb 23, 2006
    Messages:
    5,356
    Location:
    Oregon
    I don't know if it'll cause accuracy problems but the bullet can spin apart en route to the target.
     
  3. VARifleman

    VARifleman Member

    Joined:
    Feb 6, 2005
    Messages:
    1,533
    Location:
    Northern VA
    The bullet can be pointed in a different way than it's going if it's over stabilized (pointed up parallel with the barrel as it heads down) as well as blowing itself apart from spinning too hard.
     
  4. bogie

    bogie Member

    Joined:
    Jan 2, 2003
    Messages:
    9,569
    Location:
    St. Louis, in the Don't Show Me state
    Yeah - overstabilizing a bullet can turn perfectly good groups into "full choke" groups...
     
  5. Lady with a Gun

    Lady with a Gun Member

    Joined:
    May 17, 2008
    Messages:
    61
    The biggest problem with extra fast rates of twist is the bullet may be prone to self-destruct. In other words, the rate of spin will cause the bullet to fragment.
     
  6. jonmerritt

    jonmerritt Member.

    Joined:
    Dec 25, 2007
    Messages:
    463
    .44 shotgun
     
  7. Matt304

    Matt304 Member

    Joined:
    Sep 19, 2006
    Messages:
    624
    Location:
    Utica, IL
    I will get the twist for what I am currently planning on using then, only 135gr bullets. So I will go with 1:12.
     
  8. kragluver

    kragluver Member

    Joined:
    Oct 2, 2007
    Messages:
    312
    Location:
    Aledo, TX
    As alluded to here, there is an upper stability boundary for spin rate as well.
     
  9. hardhit777

    hardhit777 Member

    Joined:
    Dec 21, 2006
    Messages:
    117
    Location:
    Statesboro, GA
    So what does a bullet that fragments in mid-flight look like?

    HH
     
  10. jnyork

    jnyork Member

    Joined:
    Feb 19, 2008
    Messages:
    912
    Location:
    Arizona and Wyoming
    Kinda like a little puff of smoke, only one I ever saw.
     
  11. VARifleman

    VARifleman Member

    Joined:
    Feb 6, 2005
    Messages:
    1,533
    Location:
    Northern VA
    A blue puff of smoke I've heard.
     
  12. Loomis

    Loomis member

    Joined:
    Aug 10, 2008
    Messages:
    938
    optimum twist rate also depends on muzzle velocity.
     
  13. Ridgerunner665

    Ridgerunner665 Member

    Joined:
    Feb 3, 2005
    Messages:
    3,393
    Location:
    Upper East Tennessee
    I'd go with the 1 in 12" twist...the 308 does just fine with that twist up to and including 175 grain bullets...

    You are going to want to use 155 to 168 grain bullets out of that 10 - 14 inch barrel on your pistol anyway...the recoil and muzzle blast with the heavier bullets is downright PAINFUL.
     
    Last edited: Aug 27, 2008
  14. Ridgerunner665

    Ridgerunner665 Member

    Joined:
    Feb 3, 2005
    Messages:
    3,393
    Location:
    Upper East Tennessee
    True...the 308 does better than most think it will from 14 inch barrels though.

    110 grain bullet...2,790 fps.
    125 grain bullet...2,715 fps.
    150 grain bullet...2,612 fps. (48.8 grains of W748)
    168 grain SMK...2,480 fps (46 grains of W748)
    175 grain SMK...2,250 fps (42.9 grains of W748)...thats a handful.
     
  15. MachIVshooter

    MachIVshooter Member

    Joined:
    Aug 11, 2005
    Messages:
    14,380
    Location:
    Elbert County, CO
    Dust.

    Try shooting .22 Hornet bullets out of a .22-250 or .220 Swift and see for yourself ;)

    As for your .308, 1:10 would be fine. The .308 can't push even the light (110 gr.) bullets fast enough for the centrifugal force to exceed the integrity of jacketed rifle bullets.
     
  16. Ridgerunner665

    Ridgerunner665 Member

    Joined:
    Feb 3, 2005
    Messages:
    3,393
    Location:
    Upper East Tennessee
    MachIVshooter is right about the 308 not being able to push the light bullets fast enough to fly apart...and 1 in 10" would work...

    But 1 in 12" will give you a little more muzzle velocity.
     
  17. Sylvan-Forge

    Sylvan-Forge Member

    Joined:
    Feb 22, 2006
    Messages:
    1,224
    Location:
    Fort Myers, Florida
  18. bogie

    bogie Member

    Joined:
    Jan 2, 2003
    Messages:
    9,569
    Location:
    St. Louis, in the Don't Show Me state
    In my experience, when run run 50 grain Speer TNT out of a .22-250 at a max load, even with a 12" twist, you get a contrail of bluish-grey smoke starting past 50 yards... It was making holes in a hundred yard target tho...
     
  19. Jim Watson

    Jim Watson Member

    Joined:
    Dec 24, 2002
    Messages:
    22,343
    12" twist is already rather fast if all you are going to shoot is 135 gr benchrest .30s.
    It will be fine for anything up to 175 gr.
     
  20. big_bang

    big_bang Member

    Joined:
    Jul 23, 2008
    Messages:
    77
    For best benchrest match accuracy, you want to spin the bullet as slow as possible to stabilize it. Some benchresters will drop one twist rate (1:14 to 1:13 for example) in winter versus summer to stay right on that edge of stabilization.

    For most other purposes, as long as spin rate is somewhere between min-max you're fine. Minimum is what required to stabilize, max is based on bullet construction.
     
  21. brickeyee

    brickeyee Member

    Joined:
    Feb 25, 2005
    Messages:
    3,135
    There is no upper limit other than bullet constriction.
    Faster spin than needed does NOT introduce instability by itself.

    The problem is that if the bullet is not perfect the excess spin will cause problems.

    The bullet's longitudinal center of gravity and center of form do not match perfectly.

    The bullet travels in the barrel around center of form.
    Once free of the barrel it rotates around the longitudinal center of gravity.

    Any more spin than needed for stability increases the forces acting while rotating around the longitudinal center of gravity degrading accuracy.

    Unless you have a BR grade rifle you are unlikely to see any effect from excess spin, besides bullets simply coming apart.
     
  22. spwenger

    spwenger Member

    Joined:
    Nov 24, 2006
    Messages:
    391
    Location:
    Show Low AZ
    Begging to Differ

    This statement would be true if bullets traveled in straight lines. However, the trajectory of a bullet is shaped by gravity. Rifling conveys gyroscopic trajectory to bullets; if the gyroscopic stability is "perfect," it will lead the nose of the bullet to remain on its initial path as the bullet enters the descending phase of its trajectory. The increasing difference in angle between the direction of the nose of the bullet and its actual path will produce "yaw," where the tail of the bullet does not follow the nose of the bullet. This is the source of the inaccuracy induced by "overstabilizing" bullets with too high a twist rate. The effect may not be seen at close range but will magnify as the range increases.
     
  23. LB7_Driver

    LB7_Driver Member

    Joined:
    Jan 4, 2008
    Messages:
    107
    Spwenger has a few points, especially at very long ranges.
    Brickeyee's observations tend to hold true under most shooting conditions.

    In my experience, it is very hard to over-stabilize a bullet (barring structural limits).
    A well-made bullet will not be measurably less accurate when fired from a fast-twist barrel.
    Fast-twist barrels will bring out the poor accuracy characteristics of poorly-made bullets more than a slower-twist barrel.

    All of the above depends upon rifles of average accuracy... if we are talking about rifles that are capable of consistently printing sub-1/2 MOA groups, then you can start to measure the effects of stabilizing a bullet more than absolutely necessary.

    Good bullets, shot from a 1-MOA rifle that has a faster-than-necessary twist, will not be measurably less accurate.

    Case in point -
    A 68-grain, 6mm HP match bullet is a common bullet style for BR shooters. Most BR rifles have a 13 or a 14 twist barrel for this bullet weight/style.
    This same bullet will still print ~1/4 MOA groups from a 1-8 twist barrel.
     
  24. brickeyee

    brickeyee Member

    Joined:
    Feb 25, 2005
    Messages:
    3,135
    This only occurs at very extended range, not something about 99.9% of shooters are ever going to see.

    Yaw does not in itself represent an accuracy loss, but can represent a precision loss.

    The group can remain tight, it just will not be in the expected location.

    Cross winds are likely to spread the group significantly more.
     
  25. thrifty7

    thrifty7 Member

    Joined:
    Feb 12, 2003
    Messages:
    23
    Location:
    Maine
    Twist too fast??

    I beleive that the original question was,to paraphrase, " would a 10" twist be too fast for a .308?". Although many .308s have a 12" twist, many others have 10". The standard twist for most 30 caliber cartridges over the last 100 years has been 10"----no way is it too fast. All of the "puff of smoke" comments would only make sense if he was talking about something really radical, down in the 6" region---or so it would seem to me.
     
Thread Status:
Not open for further replies.

Share This Page