Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Buying vs building 1911

Discussion in 'Handguns: Autoloaders' started by dashootist, Jun 27, 2011.

Thread Status:
Not open for further replies.
  1. dashootist

    dashootist Member

    Joined:
    Feb 8, 2010
    Messages:
    551
    I talked to a gunsmith briefly about his Caspian 1911. He built it with top quality parts. Of course, it shoots better than anything I've ever touched.

    I'm mechanically inclined, and have always been interested in doing weekend gunsmithing. I'm thinking of building a 1911 like this gunsmith's. Is this a crazy idea? Alternatively, I can just go out and buy a Les Baer for $2000. I imagine both option would cost about the same. But wouldn't it be more fun to build it yourself?
     
  2. docnyt

    docnyt Member

    Joined:
    Sep 20, 2009
    Messages:
    1,284
    Location:
    HeArT of DiXiE
    Not only would it be fun but a good learning experience.
     
  3. MICHAEL T

    MICHAEL T Member

    Joined:
    Feb 3, 2004
    Messages:
    6,011
    Location:
    outback Kentucky
    I would go with Les Baer then move up to a Wilson later. Les make some fine hand fitted pistols. Best of all he sends in a card board box. Not a silly take up space I don't want another one plastic case. That we all pay for .
     
  4. Magnumite

    Magnumite Member

    Joined:
    Jan 9, 2004
    Messages:
    714
    Location:
    Belcamp, Maryland
    Building your own and doing all the work you can yourself will cost you $$$$. I have collected parts for a couple years knowing I was eventually going to build a gun. I got good deals on good parts I wanted to use. But it still cost me $800 (up to last year) just for parts. I haven't applied the finish yet.

    I'd say go with a built pistol, like Springfield Armory Milspec or GI. Decide on what configuration 1911 you want then acquire the proper parts to do it. Then do the mods one at a time. This way, you are starting with a working gun. If you make a modification and things don't work, you can look closely at what YOU did and find the problem. Starting with a box of parts and not being completely familiar with function and how to fit the parts can lead to malfunctions which may be caused from interrelated fitting issues you are not aware of.

    Buy a good clean used SA MilSpec. You'll pay about $450 - $550 for a good one. A new Caspian frame and slide will cost you over $425. Plus you'll have the small parts to complete the build, and can sell many of the parts you will be taking off the working pistol. Then you've acquired some experience go for the ground up build.

    Nothing like the satisfaction that YOU did all that work. Plus you can alter configurations as you learn what you like about the pistols. It would cost several thousand to have different configurations done by a gunsmith.

    If you just want a custom level finished pistol, you are better off buying a Baer or whatever brand/configuration lights you fire.
    Whichever path you choose, good luck.
     
  5. Zerodefect

    Zerodefect Member

    Joined:
    Mar 28, 2009
    Messages:
    4,643
    Location:
    Yakutsk, Sakha Republic
    It's a whole lot easier to buy a Les Baer or Dan Wesson and fix the parts that need fixing. Learning as you go, and as you upgrade the gun to suit your needs.

    Doing a whole 1911 before you've even hacked up any other 1911's is alot harder than it looks. It's not like assembling an AR15 or Glock. There are alot of very frustrating parts to fit.

    Even a perfect 1911 still needs alot of work before I'll carry it:
    -sight replacement
    -sensitize the grip safety
    -stone all the internal parts clean
    -polish the barrel throat
    -polish the magazine feed lips and install a Tripp kit

    That's quite a bit of work allready, and that's the easy stuff.



    Fusion makes kits that have all the hard parts prefitted. All you have to fit is the small stuff like:
    -Thumb safety (hard)
    -Slide lock lever (medium)
    -mag release (easy)
    - Grip safety (easy)
    -sights (medium)
    -main spring housing (easy)
    -trigger parts (super easy if you have a EB sear jig)

    So I'd get a fusion kit if you decide to go that route.
     
  6. ranburr

    ranburr Member

    Joined:
    Nov 21, 2004
    Messages:
    72
    I have done it both ways and it is much cheaper to just buy a semi-custom (Baer, Brown, etc).
     
  7. jon_in_wv

    jon_in_wv Member

    Joined:
    Jul 8, 2006
    Messages:
    3,816
    Wouldn't it, by definition, NOT be perfect then?
     
  8. 451 Detonics

    451 Detonics Member

    Joined:
    Jan 4, 2011
    Messages:
    2,442
    Location:
    Indiana
    The first 1911 I built up is the gun I used to win Regionals in NRA Action Pistol with. Started with an unfit Caspian slide and frame and a copy of Hallock's 45 Auto Handbook. Only thing I didn't do myself was cut the frame for the ramped barrel. I did cut the slide for the cone comp by hand and really wished I has access to a lathe...lol.

    If you are mechanically inclined and willing to invest in a couple specialized jigs and tools then it really is an easy build. The better the parts fir together the better the accuracy will be so plan on doing a lot of hand work and leave the Dremel unplugged. My 1911s will run with the best of them as far as accuracy. The may not be as pretty but I didn't want to pay anyone to make them pretty. Stainless slide and I had the frame done in NP3 by Robar.

    super1-1.jpg
     
  9. dashootist

    dashootist Member

    Joined:
    Feb 8, 2010
    Messages:
    551
    What's the best place online to buy a LB 1911 Primier 2?
     
  10. xr1200

    xr1200 Member

    Joined:
    Nov 12, 2010
    Messages:
    638
    This has been well discussed before, the bottom line is that unless your a student enrolled in a college gun smith course or if your are a qualified gun smith or at least a good machinist.

    You would have to be an idiot to try it.
    1. Most cases the guns assembled by amatuers, don't function well.
    2. The guns are not accurate.
    3. The gun have no real resale value. Note even worth what you could buy a cheap RIA 45
    4. You need a lot expensive tools.
    5. screw up the slide, barrel or frame and your out $150-$300

    Granted there are some ppl that are really good mechanically and have lucked out building a good 45acp, but this is rare.

    Best thing to do is buy the best 1911 you can afford, shoot it and enjoy, and don't waste time and money building one, it is always cheaper to buy a completed gun than it is to build one from scratch.
     
  11. xr1200

    xr1200 Member

    Joined:
    Nov 12, 2010
    Messages:
    638
    Search gunbroker.com auction arms and gunsamerica online I picked up a baer premier 2 with the accuracy guarantee , used unfired for $1000 a couple of years ago. Expect to pay about $1250-$1400 for a good used one and $1600-$1800 for a new one.

    Or just call around locally and find a good shop that will order you one for about a $25-$50 mark up
     
    Last edited: Jun 29, 2011
  12. Magnumite

    Magnumite Member

    Joined:
    Jan 9, 2004
    Messages:
    714
    Location:
    Belcamp, Maryland
    First time out, doing a full build with good results and no previous experience...that might be luck. But don't pass out improving or modifying working guns as total luck if one is not a smith or student in a gs program. We all learn somewhere, some time. And some of us can reason, assimilate and put into manipulative action from studying a mechanism and doing some background research.
     
  13. 451 Detonics

    451 Detonics Member

    Joined:
    Jan 4, 2011
    Messages:
    2,442
    Location:
    Indiana
    This response really surprised me.

    1. Most cases the guns assembled by amatuers, don't function well.

    I have attended a number of 1911 build parties, I would say there is a 80% success rate in those guys putting together their first 1911. I can normally predict the ones who will have problems, they are the guys trying to force parts together. A small amount of patience and attention to detail goes far. And with the high quality of the pre-fit components available a great functioning gun is not that hard to build.

    2. The guns are not accurate.

    Again, the accuracy depends on the amount of time you are willing to invest in properly fitting the parts. Most guys (and gals) are capable of building a gun that is as accurate as most non-custom 1911s.

    3. The gun have no real resale value. Note even worth what you could buy a cheap RIA 45

    Who cares, I build a gun to suit me and it is something I have pride in...I don't build them for resale. But if you start with a quality slide and frame and use quality parts it will be worth more than a cheap import.

    4. You need a lot expensive tools.

    A few stones, a couple punches, and if you buy an over sized hammer, sear set a jig is nice to have. Add in some mild abrasives for fitting and you might have 30 bucks in build tools.

    5. screw up the slide, barrel or frame and your out $150-$300

    True enough, however if you keep your hands off the power tools chances are you won't. It is like the old carpenter's saying "measure twice and cut once". You remove material in very small increments and do a lot of trial fitting. Putting together a 1911 is not like building up an AR, it does take time and patience.

    There is no reason a reasonably intelligent person cannot build a reliable and accurate 1911. There are several great books that will walk you through each step. And there is nothing better than out shooting your buddy and his high end gun with one you built yourself.
     
  14. Zach S

    Zach S Member

    Joined:
    Jun 30, 2003
    Messages:
    5,533
    Location:
    Western NC
    I like Magnumite's idea, for the same reasons.

    Although I wanted to, I didn't build a 347 stroker for my first car. Good thing too, because I had to go back into the motor I slowly built up and fix what I upgraded a few times. You have to crawl before you walk.
     
  15. Magnumite

    Magnumite Member

    Joined:
    Jan 9, 2004
    Messages:
    714
    Location:
    Belcamp, Maryland
    Most who build or modify the guns do so to obtain features they want. The greatest motivators seem to be economics, challenge to do so, they don't see configurations they like, or like me, they've been doing mechanical things since they were two years old and can handle the understanding and implementation.

    I remember when Kimber first marketed their 1911 - the Classic. It put the 1911 industry on its ear. I fiend'd for one. But I wouldn't buy it because I knew I would just have to do something to it...and it didn't need it. I eventually did get a Kimber, beaute of a Series I Gold Match. It wasn't quite what I wanted so sold it and acquired a SA Trophy Match. That gun is ladden with features. Sold it because I had too many on that platform. Shoulda kept it.

    Some go to gun shows and such looking for guns and ammo. I go to look for parts. I means whole guns are cool, we all know that, and good buy on an appealing arm does come about, but to score a good slide, couple of barrels, real GI parts...now that's cool.

    Of the 1911's I own now, only three are shadows of their original form. I've built all the others and they run well, look good, accurate and they fit and suit me. You can definitely see a progression from the earliest build to the latest. Mostly in the aesthetics. Takes a while to understand ergonomics and appealing form.

    Do I save money? Yes, but only if you look at final product. My guns built to the grade they are at will cost $1600 to $2000. Okay, I don't use the high tech finishes but the parts are good and fitting is sound. But the parts I acquire eventually are close to $1k in value. I have virtually all parts for the next build. If I marketed those as the new untouched parts they are, I am looking at about $1000 income. The complete pistol would eventually sell for more than that. Inflation, a good target and certificate from a gunsmith will help seal the deal. It will not bring Wilson Combat prices because I am a nobody in that arena. But its the same quality and I build them to keep.

    Sometimes one may acquire enough Frankenparts to build a beater or shooter. Properly done (i won't build unsafe or substandard), , I shoot them awhile, acquire new learning, many times in just what formats work and are desired. I sell them and I make a few $$$ when I sell it within a know market level. These are usually to guys looking for beaters or shooters.

    Sorry for rambling...but this subject can bring a high when you are into it.

    Here is my latest build. Still need to do the permanent finish...it will be parked. That's a full group shot off hand at 25 yards with ball ammo. It will do it all day long. Well, on shot is covered up by the quarter...but I called that. Got excited.
     

    Attached Files:

    Last edited: Jun 29, 2011
  16. squarles67

    squarles67 Member

    Joined:
    Jan 16, 2009
    Messages:
    448
    Location:
    Orange, Texas
    I've done it, I enjoyed it and I learned alot.

    There are some specialized tools involved, I found most of mine used on Ebay. As has been mentioned stay away from the power tools and stick with stones and files.

    Jerry Kuhnhausen's 1911 book Vol 1&2 was a "must" have for me and is a very good book whether you go through with the build or not.

    I wouldn't start with high end parts. Get you an Armscor frame for $90 from Sarco and learn on the low end parts. You'll learn alot the first time through. Tune on it and tinker with it and if it's your "cup of tea" then move on up to the high end stuff.

    Even if you get a pre-fit slide and frame it will not be just putting a bunch of other parts on, lots of hand fitting is required.
     
  17. Ultravox

    Ultravox Member

    Joined:
    Jan 10, 2011
    Messages:
    165
    Location:
    Minneapolis, MN
  18. Tune_up

    Tune_up Member

    Joined:
    Sep 2, 2008
    Messages:
    30
    Location:
    Southeast Missouri
    I did it, or to be honest, I did it from a Fusion kit (frame and slide fitted). Was it worth it? Depends on what you want, If you want to learn a lot, enjoy doing the work and take pride in building a 1911, sure. If you want a quality gun for the least amount of money, buy a custom or a good quality base gun and have a smith make the desired changes.
    I started from the kit and added the parts of my choice. I Ruined one safety and had to replace and I didn’t like the first set of sites so I replace those. Purchased about $50 worth of files/stones and other tools that I didn’t have. My trigger job was as good as a couple of colts I have, but ended up having a trigger job done. I also sent it off for DLC coating, (shipping both ways). I love the finished gun, it’s totally reliable, (2000+ rounds), as accurate as any gun I own except a Heinie Springfield, and I guess I have a special relationship with it since I built it, but for what I spent I could have purchased a very nice gun.
    Would I do it again? Well…...... I’ve been considering it, go figure :confused:.
     
  19. xr1200

    xr1200 Member

    Joined:
    Nov 12, 2010
    Messages:
    638
    You need more tools than a few punches and stones.

    To properly fit the gun your going to need the special slide barrel lug and frame files, bushing should be lathes turned.

    Slide to frame fitting tools, files and the bending or alignment jigs for a match fit.

    Slide groove cutters may be needed and what about a trigger, hammer, sear fitting jig.

    Plunger stacking tool and protector.

    Now how are you going to do a novak or bomar sight cut if needed on a standard gi model, don't tell me the files.

    You could probably cobble together a gi grade model with a lot of drop in or GI loose spec parts, but in most cases your not going to produce a match grade gun.

    Also resale is not existant, try and sell a no name gun cobbled together and you would be lucky to get $300 for it.

    Price putting together a good quality gun with either , brown , baer, wilson , STI, and even caspian. It would cost you almost $1000 or more for the parts alone and still you have to risk fitting everything.

    Where ppl are making a lot of wrong assumptions about building firearms, is mainly due to all the AK47 kits and ar15 kits that are easy to build and in most cases will be acceptable in accuracy and function.

    But when your dealing with the 1911 as a match grade gun, it must be fitted and assembled by a competent gun smith, who knows what they are doing.
     
    Last edited: Jun 29, 2011
  20. xr1200

    xr1200 Member

    Joined:
    Nov 12, 2010
    Messages:
    638
    http://how-i-did-it.org/1911-project/lessonslearned.html
    Also note in this documented 1911 build the author never posted any actual pics of targets at acceptable ranges, and there were even a lot of parts he scrapped and bought new ones. So if you decide to build one , then be ready for at least what this guy ran into and more.
     
  21. jackpinesavages

    jackpinesavages member

    Joined:
    Mar 17, 2009
    Messages:
    809
    Buy a Les Baer Thunder Ranch, and start stockpiling parts for your own build, in a conservative manner. See one of my other posts per 1911s and the LB TRSs.
     
  22. Magnumite

    Magnumite Member

    Joined:
    Jan 9, 2004
    Messages:
    714
    Location:
    Belcamp, Maryland
    Sounds like someone botched a build or two.
     
  23. viking499

    viking499 Member

    Joined:
    Feb 9, 2007
    Messages:
    3,441
    I built one over the winter. Remsport bobbed stainless frame and slide and Ed Brown and Fusion parts. Cost was OK. Experience gained from it was worth a lot to me. Still tinkering and polishing out a few "bugs", but would do it again if given the chance.
     
  24. mgmorden

    mgmorden Member

    Joined:
    May 22, 2009
    Messages:
    4,576
    Location:
    Charleston, South Carolina
    I'd go the buy route. 1911's aren't quite like AR15's or 10/22's where all the parts are drop ins and you just choose high quality and go from there. There's a lot of hand tuning and tweaking involved, and if you don't get it quite right then in the end you've got a $1000-2000 gun that constantly jams.
     
  25. Chris Rhines

    Chris Rhines Member

    Joined:
    Dec 22, 2002
    Messages:
    3,773
    Location:
    Potomac, Maryland - Behind enemy lines!!
    Nothing wrong with building a 1911, everyone should give it a try at least once.

    Don't underestimate the difficulty and the expense, though. Building a 1911 is a long, involved, fiddily process. You absolutely will need some special tools - hammer/sear fixture, plunger tube staking punch and support, extractor gauge, vise, files, etc. You will also most likely ruin at least one expensive part.

    If you're not already familiar with the 1911 platform, I would buy a quality pistol from Colt, Springfield, S&W, etc. Then look at building one, if you're still of a mind to. Having a working 1911 to refer back to could be handy.

    -C
     
Thread Status:
Not open for further replies.

Share This Page