Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Cap sizes; Uberti 1851,1862 and Pietta 1858, 1862

Discussion in 'Blackpowder' started by tomykay12, Feb 10, 2013.

Thread Status:
Not open for further replies.
  1. tomykay12

    tomykay12 Member

    Joined:
    Jun 26, 2011
    Messages:
    38
    Hi. I am starting to collect BP supplies and paraphenalia(sp) with much help from this forum, thankyou. I have read quite a bit regarding cap sizes, but am still a little hazy. I own an 1858 Pietta, NOS about 15 yrs old, unfired. I noticed the nipples are somewhat peened over, as if it was dry fired a fair amount. It was a gift from a friend, and came from Cabelas. Bottom line here is I will replace the nipples on this piece with parts from Possibles or TOW, so those will use # 11's, correct?? I have an 1851 Navy Uberti coming soon , thanks to Standing Wolf here at THR, also NOS, unfired, guessing 5-8 yrs old. I don't know what cap size this would take, 10 or 11. Also in my near future are probably a Pietta 1862 pocket, and it's smaller cousin the Uberti 1862 pocket police. Same issue; Don't know which size . I would like to buy semi bulk, and must mailorder, as there is nothing available locally. Would it make sense, at 32.00 approx per revolver to standardize everything with new nipples for #11 caps? Does that work on the pocket models as well, or do they mandate the smaller caps??
    Thanx in advance for help here; i am trying to keep hazmat and multiple shipping fees to a minimum, best, tomas

    ps, definitely gone into the deep end of the black powder pool, lol
     
  2. Prairie Dawg

    Prairie Dawg Member

    Joined:
    Mar 16, 2008
    Messages:
    615
    Location:
    Ohio
    If yer gonna shoot them & you want them to be reliable, go with Treso nipples and Remington caps. I but the nips at The Possible Shop.
    http://www.possibleshop.com/s-s-nipples-cb.html
    I've not used the new SlixShot nips, but I have heard good things.
    --Dawg
     
  3. tomykay12

    tomykay12 Member

    Joined:
    Jun 26, 2011
    Messages:
    38
    That is where my reading has led, thanx, tk
     
  4. Prairie Dawg

    Prairie Dawg Member

    Joined:
    Mar 16, 2008
    Messages:
    615
    Location:
    Ohio
  5. Fingers McGee

    Fingers McGee Member

    Joined:
    Apr 5, 2009
    Messages:
    1,511
    Location:
    High and dry at Lake of the Ozarks, MO
    I've always found the #10 Remingtons to be the best all round cap regardless of whose nipples are on the cylinder.
     
  6. Pancho

    Pancho Member

    Joined:
    Oct 23, 2007
    Messages:
    1,874
    Location:
    Southwestern, Ohio out in the country about 40 mil
    Tomykay, I'm big on using the phone calling the suppliers and determining if they know what they're talking about. TOW was great. Tell them what gun you have and ask them what nipple it needs and what cap it is designed for. Sure worked for me.
     
  7. tomykay12

    tomykay12 Member

    Joined:
    Jun 26, 2011
    Messages:
    38
    Yes sir, I heartily agree and will do that with both TOW and Possibles regarding nipples. I am a little out of my element here, and the forum has been a great help; both responses to questions and stickies/ archives. All the knowledge gained from generous folks willing to share is great. tk
     
  8. Hellgate

    Hellgate Member

    Joined:
    Jan 11, 2004
    Messages:
    1,440
    Location:
    Orygun
    I'm in Fingers McGee's camp: the Remington #10 cap fits the widest variety of nipple sizes & shapes than any other cap. If your gun won't take the Rem 10 it can be easily made to.
     
  9. Pancho

    Pancho Member

    Joined:
    Oct 23, 2007
    Messages:
    1,874
    Location:
    Southwestern, Ohio out in the country about 40 mil
    In a nut shell, If you can't talk to the people that make the nipple and get a straight answer as to what cap should fit their nipple I'd hang up and try again.
    We have the power through our pockets to advise and control the criteria that they design and build their afermarket nipples.
     
  10. Prairie Dawg

    Prairie Dawg Member

    Joined:
    Mar 16, 2008
    Messages:
    615
    Location:
    Ohio
    Treso nips are made by House of Muskets in colorado.
    800-367-9250
    --Dawg
     
  11. tomykay12

    tomykay12 Member

    Joined:
    Jun 26, 2011
    Messages:
    38
    So..., I talked to TOW today. They were apparently quite busy and the guy was short, but polite and direct. Gave me the nip # for the 1858, and the 1851, and said they are fitted to CCI# 11's, and that rem 11's would be a little loose but work. Makes me wonder if rem 10's would fit. One issue is he said the 1858 has two lengths available, and the only way to know is order a set, if that dosen't work, return and order the other.....I hate that. Going to try Possibles tomorrow, as they didn't answer today. Sure wish I could just get a few different cap sizes locally soz I could figger out what to bulk buy. Nobody has anything, the ammo shelves are bare, and everyone in the stores is grumpy and sorta rude. Thanx everyone for the tips, tk
     
  12. Prairie Dawg

    Prairie Dawg Member

    Joined:
    Mar 16, 2008
    Messages:
    615
    Location:
    Ohio
    Remington #10 and #11 are the same diameter.
    #11 are shorter.
    Treso Nips were designed to fit Remington caps.
    --Dawg
     
  13. Noz

    Noz Member

    Joined:
    Dec 3, 2010
    Messages:
    794
    Location:
    Southwest Missouri
    Yup!
     
  14. tomykay12

    tomykay12 Member

    Joined:
    Jun 26, 2011
    Messages:
    38
    OK, I believe everyone!! I'll try 10's when i can findem. Talked to Possibles this morning. The fella just referred me to the website. No time, said he. At least Wolf gave me one minute and some part #'s. I do need a set of nips for my Pietta to make it functional. Think I'll just relax, wait awile and let my dollars sleep, tk
     
  15. Hammerdown77

    Hammerdown77 Member

    Joined:
    Apr 29, 2010
    Messages:
    604
    Location:
    North Alabama
    I'm using the factory nipples for my Pietta 1860 Army, but I ordered another set of stainless nipples from Dixie Gunworks. Have you checked with them?

    The stock nipples on my Pietta work well with CCI #10 caps. CCI #11s are a little big and won't stay on without pinching them closed a bit. Have not tried Remingtons.
     
  16. BHP FAN

    BHP FAN Member

    Joined:
    Sep 23, 2008
    Messages:
    5,810
    Location:
    Northern California
    Remington #10, and CCI #11 work, CCI#10 are too tight.
     
  17. tomykay12

    tomykay12 Member

    Joined:
    Jun 26, 2011
    Messages:
    38
    My stock nips are all peened over; someone dryfired the heck out of this piece I am guessing. Otherwise NIB, approx 15 yrs old. hence my search for caps AND nipples. I definitely see the reason for good fitting caps, and the reason NOT to squeeze them oval. I'll check DGW and some other sources as well for nips. Thanx, tk
     
  18. Dellbert

    Dellbert Member

    Joined:
    Mar 12, 2011
    Messages:
    162
    Location:
    NC
    I went through all this nipple stuff a while back. I found that just sticking with the stock nipples and ordering the Rem #10 caps by the thousand is the easyest way to go till you haft to change the nipples. Heck some of the new guns you still haft to squeeze the #10s to keep them on.:banghead:
     
  19. Jaymo

    Jaymo Member

    Joined:
    Aug 21, 2010
    Messages:
    3,530
    Remington 10s are the hardest for me to find locally.
    I installed TC #11 nips on my Howdah, because I was getting too many "nip slips" with the factory nips and CCI 11s.
    I save my Rem 10s for my Italian revolvers.
    CCI 10s seem to be too tight and require 2 smacks to fire.
     
Thread Status:
Not open for further replies.

Share This Page