Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Commander locking open before empty

Discussion in 'Handguns: Autoloaders' started by RJ357, Sep 18, 2004.

Thread Status:
Not open for further replies.
  1. RJ357

    RJ357 Member

    Joined:
    Jun 9, 2004
    Messages:
    280
    Location:
    VA
    I was shooting my Colt commander series 80 today. At one point, the slide locked open after the first round. Thinking I might have hit the lever, I paid attention to how I was holding it. It locked open again after the 3rd round. The remaining dozen or so rounds were OK.

    I was not able to move a round in the magazine forward or left far enough to hit slide lock. So I don't think that was the problem.

    Gun is almost new, maybe 300 rounds through it. Winchester 230 gr ball. Magazine was a Mec-Gar.

    Anything I can check for?
     
  2. PinnedAndRecessed

    PinnedAndRecessed member

    Joined:
    Aug 10, 2004
    Messages:
    1,542
    1911 Tuner is the guy you want to ask, but where'd the clip come from? It's not OEM and I think I'd experiment with different ones.
     
  3. FJC

    FJC Member

    Joined:
    Dec 26, 2002
    Messages:
    391
    Location:
    Michigan, USA
    Check the slide stop and see if the bullets in the mag are hitting it and nudging it up.

    I ran into this problem in my Commander. I took the slide stop and carefully stoned down the area where the bullets were rubbing.

    With the pistol disassembled, if you put a magazine with a couple rounds loaded (be very careful! only in a disassembled pistol!) and insert it in the mag well, you can see if they are hitting the slide stop. Slide the top round forward a bit as well, as that can happen when firing.

    It took a few times for me to get it to the right amount of stoning to stop the problem. Be careful not to take off too much metal, or your slide won't lock back when the mag is empty.
     
  4. RJ357

    RJ357 Member

    Joined:
    Jun 9, 2004
    Messages:
    280
    Location:
    VA
    PinnedAndRecessed -
    It's an almost new Mec-Gar magazine.

    FJC -
    I tried checking for bullets or cases hitting the slide stop and I couldn't get one to move close enough to hit it.
     
  5. FJC

    FJC Member

    Joined:
    Dec 26, 2002
    Messages:
    391
    Location:
    Michigan, USA
    Hmm my next guess would be to check if the plunger tube spring is too soft (not putting enough tension on the slide release lever so it's "bouncing" up under recoil) - but I'm now gonna punt and say, "See what 1911Tuner has to say."

    :)
     
  6. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    Premature Lock

    Howdy Ruger,

    FJC and P&R pretty well nailed it. There's maybe one other reason, but it usually doesn't show unless the slidestop is an extended type or the area where the plunger pin makes contact is wrong.

    Inertial mass...heavy stop...will sometimes cause one to bounce upward
    enough to engage the slide and stop it. When it happens, it's usually just
    barely catching on the corner. If the stop is standard, it can happen if there's not sufficient clearance bwtween the stop and the slide.

    Magazine out, pull the stop down as far as it will go and hold it. Use a feeler gauge to chack the gap betwen the top of the stop and the slide.
    I like to see .012-.015 inch...but .010 will usually do unless the plunger spring is seriously tired. Check the pin too...it may be worn flat on the end,
    which changes things and reduces engagement tension a little.

    Be aware that even though you can't see the side of the bullet making contact with the lug by manipulating it manually, doesn'yt necessarily mean that it's not happening. The dynamics of live firing is a little different, and
    things could be flexing just enough to let it happen. Not likely...but still a possibility. I'd say that if there's as much as .015 inch clearance, it's probably not contacting, and something else is in the works.

    Luck!

    Tuner
     
  7. RJ357

    RJ357 Member

    Joined:
    Jun 9, 2004
    Messages:
    280
    Location:
    VA
    1911Tuner -

    I'll check the clearances and report back here if they're too close. I can try a different magazine too.

    Thanks all
    RJ
     
  8. magsnubby

    magsnubby Member

    Joined:
    Apr 20, 2004
    Messages:
    915
    Location:
    fresno,ca
    Did you try any mags other than the Mec-Gar's? I bought 2 Mec-Gar mags to use in my Charles Daly 1911 and my RIA Commander. Neither one worked in the CD (slide locked back every 2 or 3 shots). Both worked in my RIA. Both worked in my buddy's RIA Commander. Only one worked in his Springfield.

    The gun store owner said that was a common problem with Mec-Gar mags in 1911's. He replaced them both. Both worked in all of the above guns.
     
  9. scbair

    scbair Member

    Joined:
    May 5, 2003
    Messages:
    611
    Location:
    South Carolina
    Tuner is on the money.

    My saga; My Kimber Ultra slide would lock open prematurely (only once or twice every 50 rounds, but that was unacceptable to me; this is my serious biz sidearm!).

    OK, slide stops aren't too expensive; I bought one & set the original aside. Did some cutting & polishing at the "contact" point. Result? Occasional premature slide lock continued; now coupled with occasional failure to lock on an empty mag! This enlightened me to the fact that the premature slide lock was definitely inertial, not tolerances. Lightweight pistol + .45 ACP recoil impulse = slide bouncing upward during recoil.

    Back to the drawing board.

    Second slide stop purchased. This time, I followed a clue I read in a gunsmithing manual. I CAREFULLY dremeled a SLIGHT indentation at the rear of the slide lock, where the plunger engages. PRESTO! Flawless functioning over the past several hundred rounds. Locks when it should, doesn't lock prematurely.

    Just what worked for me. . .
     
  10. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    Dremeled a Dimple

    That will work...but ya gotta be careful or you can ruin the stop...and it's back to the drawin' board. The Wilson Bulletproof stop is machined steel,
    and has a step milled into it for just that purpose. Some of'em require a little tweakin' so that the stop will lock the slide when it's supposed to...in
    some pistols. Others will drop right in and go to work. The Wilson stop is pricey. I'd try a new plunger spring...and pins if they;re worn...before spendin' the money. Always try the cheapest route first.

    Luck!

    Tuner
     
  11. RJ357

    RJ357 Member

    Joined:
    Jun 9, 2004
    Messages:
    280
    Location:
    VA
    OK, I checked a few things.Here is what I found:

    The clearance between the top of the slide stop and bottom of the slide was between .017" and .020"; the lower value with the slide pressed down to the frame and the higher with the slide pulled upward.

    The spring tension on the plunger seemed the same as that on two other almost new guns. One a Springfield new production WWII, and the other a Colt 1991 Govt model.

    When I first checked the bullet clearance, I did so with slide off. I moved the magazine down in the frame until the bullet was next to the slide lock. I checked this again, pushing the bullet to the left and it looked like it could hit.However, I thought the rounds might be in different vertical positions in actual operation, so I checked again with the slide on.

    The top round sits above the slide lock, so that this one shouldn't be able to hit it. Then I put an empty case on top in the magazine so I could see the round below it. When the top round pops up after the breechface clears the rear of the case, the round below doesn't move up far enough to reach the slide stop. Not even close.

    There is no spring tension pushing the slide stop down, just friction from the plunger pressing against it.

    Anything I can look for at the next time it occurs?
     
  12. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    All Systems Go

    Okay...Looks like no bullet contact on the lug.

    If there's a shock buffer in the gun, take it out. That'll do it sometimes...
    Don't ask me why, 'cause I ain't quite got that one figgered out yet myself...
    but sometimes it will, especially in a Commander.

    Have you changed anything about the gun? Did you install an 18-pound recoil spring? If you did, get a 32-coil Wolff GM spring and cut it down to 24 coils and check for coil bind. Trim a half-coil at a time until it doesn't bind.

    Does it do it with all magazines...or just one or two? Tolerances will sometimes let a magazine shift to the left just a hair, and let the bullet nose bump the lug. If it's just one, chack that magazine by pushing it to the left while you push it into the well to look for contact.

    Standin' by...
     
  13. RJ357

    RJ357 Member

    Joined:
    Jun 9, 2004
    Messages:
    280
    Location:
    VA
    Gun wasn't new but was like new in box. I'm pretty sure everything is stock, but I can't be absolutely certain. But I'll try and check.

    I will also try a different magazine.

    Here's an idea. The second round down can't reach the slide stop. But could the top round be getting hit hard enough by the ejecting case to move down in the magazine and under the slide stop and then up again?
     
  14. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    Ban the Bump

    Ruger asked:

    But could the top round be getting hit hard enough by the ejecting case to move down in the magazine and under the slide stop and then up again?

    Not likely...but anything's possible.

    The round under the one that's on top is the one doin' the bump if that's what's raising the slidestop. It does it as the slide gets off of it in recoil, and the round nudges the lug as it rises into feeding position...Next time it happens, take notice if the stip is fully engaged or if it's just barely catching on the corner. Full engagement suggests bullet contact...partial engagement usually means inertial bounce. Lightly beveling the back corner cures it once in a blue moon...but it usually requires more. I'd try a
    new plunger spring first..and push the mag in until the bullet ogive is aligned with the lug. Stone the backside of the lug a little on the same angle as the ogive and see if it gets any better. If it does...even a little...you're on the right track. The nudge engagement is more likely to happen with factory hardball...strangely enough. A handloaded ball round with a .010 or .015 inch deeper seat on the bullet may cure it completely.
    Factory ball OAL runs from 1.255 to 1.270 inch...with 1.260 about average.
    Try 1.250 inch OAL and see what happens...or try a cartridge with a truncated cone bullet ogive. Anything to eliminate the obvious. If none of that helps, you've got something else workin'. It's usually somethin' simple, though...Weak plunger spring/worn plunger...Inertia...Bullet contact.
    That's about covered everything unless the angle at the back of the stop has been altered.
     
  15. Dave Sample

    Dave Sample member

    Joined:
    Feb 19, 2004
    Messages:
    1,022
    Location:
    Prescott, AZ
    I like Tuner's new red neck pistolwrench john travis stuff. I may change mine to "I make 'em SING and BLING!" It is a slide stop problem. One thing that has not been considered is the back angle of the slide stop and how it's polished back there. There are two angles here and either one could have an effect on this malfunction. Does this 1911 do the thing with semi-wadcutters otr other bullet shapes? Commanders should not have shok-buffs ot guide rods in them in my opinion. The slide stop could be catching the follower but I rather doubt that. The back of the slide stop can be changed to to make it come up harder or softer. I don't care for dimples, either.
     
  16. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    Redneck PistolWrench

    Dave said:

    I like Tuner's new red neck pistolwrench john travis stuff.
    ____________________

    :cool:
     
  17. Dave Sample

    Dave Sample member

    Joined:
    Feb 19, 2004
    Messages:
    1,022
    Location:
    Prescott, AZ
    I meant to say "I LOVE IT" !
     
  18. RJ357

    RJ357 Member

    Joined:
    Jun 9, 2004
    Messages:
    280
    Location:
    VA
    That part confuses me. What it looked like, the second round in the magazine could not rise enough to hit the slide stop when the slide moved back and the top round rose to the top of the magaine.
    Then, when the slide moved forward and pushed the top round out of the magazine, the next round could rise enough to hit.
    However, the slide is too far forward at that point. The slide notch is forward of the stop.
     
  19. George Hill

    George Hill Member

    Joined:
    Dec 22, 2002
    Messages:
    6,842
    Location:
    Uintah Basin, UT
    How can the follower be causing the problem hitting the stop when:
    A. This happens as early as the 3rd round in the mag.
    B. That's what a follower is supposed to do when the gun is working right anyway.

    The bullet shape question is valid, and so is the spring tension...
    However if it's already addressed that bullets are not touching it, then it's gotta be that the lever is bouncing. This might not be from the spring - but from a worn or impropperly made lever.

    Have you tried a replacement lever from another gun?
     
  20. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    Confusion

    Okay...I re-read my post and can see how you got confused.
    Lemme try to do it mo' betta this time...

    It's probably either the bump or the bounce...That's what does it 90% of the time. If it's the Bump, here's how it happens.

    The pistol fires, and the slide starts back, The next round to be fed isn't
    quite in feeding position, but as it moved upward in the magazine to the
    pre-feed position, it touched the lug as it moved up, and is probably lightly touching it as it waits to move into full position. When the slide moves bazck far enough to get off the round and let it move into feeding position,
    it pushes the stop a little more, and it engages the slide.

    To see if the bullet is making contact, install the slidestop in the frame in its normal position. Remove the mag catch from the gun so you won't have to fiddle with it. Load a round or two into a magazine, and watch the area
    with a good flashlight while you slowly move the magazine up and down
    to simulate the rounds rising in the mag. There should be no contact
    between bullet ogive and slidestop lug. None.

    If it's the Bounce...Which is rare with a standard slidestop unless something's wrong with the angle at the back or the plunger pins or spring...it can be caused by too little clearance between stop and slide...
    or even the recoil spring being too light or too heavy. I've seen the recoil spring have an influence on it occasionally. Not often, though.

    I'm with George...Try another stop and see if it goes away.
     
  21. Missouri Mule

    Missouri Mule Member

    Joined:
    Dec 30, 2002
    Messages:
    428
    Location:
    Mid, MO
    I am thinking ....a new recoil spring mabe ......a X-tra power Wolff.

    Worked for me and my Kimber!
     
  22. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    Worked in a Kimber

    Missouri Mule said:

    I am thinking ....a new recoil spring mabe ......a X-tra power Wolff.

    Worked for me and my Kimber
    ______________________

    Interesting...I've seen premature lock that was related to recoil spring load
    three times...and in all three, it was because the gun was oversprung.
    Going to a lighter spring solved the problem.

    Was your Kimber a full-sized gun, or a shortened variant? Which spring rating did yours respond to?
     
  23. Missouri Mule

    Missouri Mule Member

    Joined:
    Dec 30, 2002
    Messages:
    428
    Location:
    Mid, MO
    1911Tuner

    The pistol I am referring to is a Kimber SS Compact II.
    Ammo is 200 gr+p Gold Dots.

    It was experiencing premature slidelock with the (22 lb factory spring, per kimber tech.. I installed a 24 lb wolff and the problem went away.

    I don't have the answer..I am not a pro.

    What I do know is it helped my pistols failure.

    I typically shoot standard loads for pleasure and defense / CCW.

    I was given a few boxes of the +P Gold Dots to try. I'm not wild about them so I don't carry them.

    I was merely offering feedback.... sorry.
     
  24. 1911Tuner

    1911Tuner Moderator Emeritus

    Joined:
    May 22, 2003
    Messages:
    18,550
    Location:
    Lexington,North Carolina...or thereabouts
    Sorry???

    Missouri Mule...NO NO! I wasn't raggin' on ya. I appreciate your input. I was just curious to know the details. I'm still studying the different effects that playing with the recoil spring has...Seems like I hear of something different every time I turn around, and I'm still trying to determine exactly why one change takes it one direction, and the same one in another gun will go exactly opposite to what usually happens. It's almost like practicing medicine...About the time ya thing you've got a specific question nailed, it'll throw a curve, and it's back to the drawin' board.

    Sorry if I sounded like I was takin' it wrong. Didn't mean it that way.
     
  25. wally

    wally Member

    Joined:
    Jan 2, 2004
    Messages:
    12,737
    Location:
    Houston, Tx
    I've a theory that the new PTFE "super" lubes might have something to do with it. I had this happen with my four most recent 1911 guns (Charles Daly EMS, Kimber BP Pro, Kimber BP Ten II, & Springfield Micro Compact). None did it first time out, but started after the initial cleaning and my use of Dupont Perfomance "dry lube".

    Seemed random in terms of rounds fired from the mag at the time. And since it sometimes happened with my 200gr lead SWC reloads I figured it couldn't be the "bump" cause the nose is too narrow to ever touch the lug.

    I've put little dimples in the slide stop with a small drill bit to give the plunger a litte more to work with. Seems to have solved the problem in all three guns.

    OTOH, could be a rash of weak plunger springs going around :)


    The slide stop in my Colt GM series 80 had the "bump" but the problem was the "notch" the slide rides in was too wide letting the lug move too far inward. Swaped slide stops with it and my Norinco and problem switched guns. Grinding the lug enough so it couldn't make contact with a 230gr RN bullet caused it never to lock back so I picked up a replacement slide stop at a gun show and problem solved.

    --wally.
     
Thread Status:
Not open for further replies.

Share This Page