Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Converting a 1911 10mm to 40 S&W

Discussion in 'Handguns: Autoloaders' started by Whitman31, Aug 25, 2008.

Thread Status:
Not open for further replies.
  1. Whitman31

    Whitman31 Member

    Joined:
    Jul 2, 2007
    Messages:
    413
    Location:
    Minnesota
    I read a previous post talking about converting a 45 1911 to 10mm. It sounded like a PITA. Does anyone have any experience converting a 10mm 1911 to 40 S&W?

    Thanks
     
  2. wally

    wally Member

    Joined:
    Jan 2, 2004
    Messages:
    12,737
    Location:
    Houston, Tx
    Should just need a .40S&W barrel and .40S&W magazine, although your 10mm mags might work.

    OTOH I don't think 10mm 1911s are much easier to find than ones that come in .40S&W.

    --wally.
     
  3. Rock

    Rock Member

    Joined:
    Feb 3, 2004
    Messages:
    80
    Also a lighter recoil spring. I use a 17 lb. in my .40 1911.
     
  4. sqlbullet

    sqlbullet Member

    Joined:
    Jan 16, 2008
    Messages:
    445
    Fit a 40S&W barrel. That should be it.

    I would not invest in new springs or mags until I had issues. Most 10mm guys immediately get stiffer springs, so the stock ones will probably be fine unless you run really light loaded 40's. The mags are frequently identical.
     
  5. farscott

    farscott Member

    Joined:
    Dec 29, 2002
    Messages:
    1,517
    Location:
    Athens, AL, USA
    To switch a 10mm 1911 to .40 S&W, the following should be done.

    1) Fit new barrel and barrel bushing.
    2) If loading .40 S&W long, use 10mm magazines. If not, try 10mm magazines. If you have magazine issues, buy some .40 S&W magazines.
    3) Match new recoil spring to your load.

    I basically went the other way when I switched my SVI from .40 S&W to 10mm.
     
  6. JDGray

    JDGray Member

    Joined:
    Sep 16, 2005
    Messages:
    5,131
    Location:
    SW MI.
    Get into reloading, and reduce some loads:) Kinda like shooting 38s from a 357Mag;)
     
  7. SDGlock23

    SDGlock23 Member

    Joined:
    Apr 1, 2005
    Messages:
    659
    Location:
    Kentucky
    Hey guys, I'm thinking about doing the same thing with my Kimber 10mm. I like it, and even reload, but I shoot .40 way more than 10mm and it seems like my expensive Kimber just sits around.

    I see KKM and Jarvis and Barsto offer barrels, but what, if any ramp style do I need? What setup do you guys have?
     
  8. sqlbullet

    sqlbullet Member

    Joined:
    Jan 16, 2008
    Messages:
    445
    SDGlock23 - Call up one of the above and ask them what ramp cut is standard on your Kimber. They will probably know, or at least be able to tell you what to measure to find out. I am ignorant of the differences, and 2 minutes on Google didn't enlighten me, other than the frame cut is different (maybe).

    JDGray - That was my first impression too. However, on second thought, 40S&W brass is essentially free to pick up at the ranges I go to. I typically lose about 10-15% of my 10mm brass on a visit (brass that gets tossed forward into no man's land). Being able to come home with 10-15% more brass instead of less is attractive.

    --Edit
    A little futher reading on google links I found this thread at 1911forum. Indicates a Nowlin ramp.
    --/Edit
     
  9. SDGlock23

    SDGlock23 Member

    Joined:
    Apr 1, 2005
    Messages:
    659
    Location:
    Kentucky
    I appreciate your help sqlbullet.
     
Thread Status:
Not open for further replies.

Share This Page