Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Cosmoline removal?

Discussion in 'General Gun Discussions' started by Glockfan.45, Oct 13, 2006.

Thread Status:
Not open for further replies.
  1. Glockfan.45

    Glockfan.45 member

    Joined:
    Sep 7, 2006
    Messages:
    1,369
    Location:
    Democratic Peoples Republic of Illinois
    Sorry if this thread already exist. I searched for almost an hour and every time I searched the term cosmoline it just gave me threads that the user name cosmoline posted in. I just bought my first surplus rife (a yugo sks) and found myself shocked at the amount of cosmoline they managed to pack this thing in :eek: . I have never had to clean one up like this before whats the best method? Honestly I am tempted to heat the oven up, put the parts in an old pan, and melt the gunk off. However a small voice inside me says thats a bad idea. How do you guys clean your mil-surps?
     
  2. Beren

    Beren Moderator Emeritus

    Joined:
    Dec 30, 2002
    Messages:
    2,388
    Location:
    Pittsburgh, PA
  3. Lonestar.45

    Lonestar.45 Member

    Joined:
    Sep 3, 2004
    Messages:
    1,077
    I stripped mine down completely, then put the wood and the gas tube with the wood on it into the oven at 160 in a "boat" of aluminum foil (to keep it from dripping into the oven) and the oven door cracked open slightly. Keep the temp low, do not get it too hot. Pull the wood out every 20 minutes and wipe down with a mineral spirit soaked rag. Keep doing this until it stops seeping out. It took mine about 2 hours.

    As for the metal, I used brake cleaner and cleaned the heck out of it. For the trigger group and magazine w/ all those springs, I put them in a pot of boiling water on the bbq pit side burner, then pulled them out and used brake cleaner. After all the metal was done, a good wipe down with Breakfree CLP, put it all back together,and you're good to go!
     
  4. eng23ine

    eng23ine Member

    Joined:
    Apr 30, 2006
    Messages:
    225
    Location:
    North Carolina
    I just dumped all the metal parts into a tube of kerosene overnight, rinsed with garden hose and dried/oiled it. Took care of 95% of the cosmo.
     
  5. mete

    mete Member

    Joined:
    Dec 31, 2002
    Messages:
    3,579
    Location:
    NY
    Somewhere in the internet is an 'oven' made to remove cosmoline. It was made with two metal garbage cans with three lightbulbs used to provide heat [your wife won't appreciate the use of the kitchen stove !!!] 150 F will melt it out , then you can use solvent for the little remaining.
     
  6. jhco50

    jhco50 Member

    Joined:
    Sep 4, 2005
    Messages:
    285
    Gasoline :what:
     
  7. Dienekes

    Dienekes Member

    Joined:
    Dec 26, 2002
    Messages:
    1,905
    Location:
    Wyoming
    After picking up my Yugo SKS I stopped at the local carwash, laid it out in the car bay, and set the machine to "grease removal". Blasted the heck out of it which got 95% of the cosmoline out. All the gunk went down their drain, not mine. Still had to get the remnants out of the nooks and crannies but after that it was pretty routine.

    Sort of a variation on Colt's ad years ago where they showed one of their new stainless 1911s in a dishwasher.
     
  8. Cosmoline

    Cosmoline Member

    Joined:
    Dec 29, 2002
    Messages:
    23,648
    Location:
    Los Anchorage
    What did I do this time? :neener:

    Seriously, do a thread search on this one. There are several really good collections of information. Maybe they should be posted via sticky?
     
  9. thexrayboy

    thexrayboy Member

    Joined:
    Sep 3, 2006
    Messages:
    1,324
    Location:
    northern nevada
    Using a coin op car wash as Dienekes says is a good start. I have a pressure washer that I hook up directly to my hot water heater. A hot stream of high pressure water will take cosmoline off real fast. What little is left when I finish is easily handled with a can of brake cleaner or carb cleaner. After that its clean and oil as usual.
     
  10. TimboKhan

    TimboKhan Moderator

    Joined:
    Apr 15, 2005
    Messages:
    8,139
    Location:
    Greeley, CO
    You can melt it off, and www.surplusrifle.com has a neat how to on how to build a rifle "oven" to do just that. Essentially, its a garbage can with some hi-watt lightbulbs in it. Not necessarily a better way, in my view, but different and effective.
     
  11. Banshee

    Banshee Member

    Joined:
    Sep 24, 2006
    Messages:
    88
    Location:
    East Tennessee
    I use a 6 inch dia PVC pipe about 4 foot long with screw on end caps. Fill it with Varasol and place the stripped gun in and let it soak for a day or so.
     
  12. Banshee

    Banshee Member

    Joined:
    Sep 24, 2006
    Messages:
    88
    Location:
    East Tennessee
    I don't why the repeat
     
    Last edited: Oct 14, 2006
  13. Banshee

    Banshee Member

    Joined:
    Sep 24, 2006
    Messages:
    88
    Location:
    East Tennessee
    ?
     
    Last edited: Oct 14, 2006
  14. Ben Shepherd

    Ben Shepherd Member

    Joined:
    Feb 27, 2004
    Messages:
    4,755
    Location:
    Utah
    Engine brite foamy engine cleaner.

    Foams all the cosmoline out of nooks and crannies, doesnt hurt any paint markings like the yardage markers on an m59/66 grenade sight.
     
Thread Status:
Not open for further replies.

Share This Page