Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Dan Wesson 500 S&W?

Discussion in 'Handguns: Revolvers' started by Magnuumpwr, Jun 10, 2012.

Thread Status:
Not open for further replies.
  1. Magnuumpwr

    Magnuumpwr Member

    Joined:
    Feb 28, 2005
    Messages:
    1,032
    Location:
    Southeast Texas
    Does anyone know if Dan Wesson produced a changable barrel revolver in 500 S&W? I purchased the gun today, barrel shroud says 357 supermag. Looking on line the 357 supermag is compatible with 357 mag and 38 spl, but these two rounds simply fall through the cylinder and barrel. 44 mag falls through the cylinder, but not the barrel. 500 s&w fits the cylinder, but seems a little too tight at the forcing cone. I am waiting for my password to "The Dan Wesson Forum", but have yet to receive it. If anyone here could help I would greatly appreciate it. Thank you in advance.
     
  2. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    They didn't as far as I know.

    The .357 Supermag was popular many years ago for silhouette shooting competation.
    The .500 S&W only came out in 2004.

    Sounds like somebody maybe tried to rechamber it to something else.
    Could be .500 S&W, .500 Wyoming Express, .500 Maximum, etc.

    rc
     
  3. Loosedhorse

    Loosedhorse member

    Joined:
    Aug 4, 2008
    Messages:
    3,454
    Location:
    eastern Massachusetts
    No .500 revolvers.

    DW went bankrupt and pretty much stopped producing revolvers in 1995. The .500 was introduced in 2003.
     
  4. buck460XVR

    buck460XVR Member

    Joined:
    Feb 6, 2007
    Messages:
    5,814
    Sounds like a "Frankenwesson".
     
  5. Steve CT

    Steve CT Member

    Joined:
    May 19, 2011
    Messages:
    532
    Location:
    Central CT
    There were some made in .460 Rowland, definitely none in .500 S&W.

    Possibly a one off that someone had customized. It's possible that a custom barrel was made to fit into the shroud and the cylinder was reamed.

    What caliber was it sold to you as?
     
  6. Lost Sheep

    Lost Sheep Member

    Joined:
    Aug 16, 2009
    Messages:
    2,661
    Location:
    Alaska
    How many rounds in the cylinder?

    Do you have pictures? How much metal is between the chambers and between the chambers and the outside of the cylinder?

    If you can't trace the gunsmithing work that (apparantly) rechambered and rebarrelled this gun, you may have to take a chamber cast to determine what it is chambered for.

    Lost Sheep
     
  7. hardluk1

    hardluk1 member

    Joined:
    Mar 27, 2009
    Messages:
    4,405
    Location:
    nc mountains
    Dan Wesson was bought buy CZ in 2005 and they did produce revolvers. Stopped again. price and qc went to poop land. They have retooled for the 715 model and produced only a small run. Who knows today. No 500.
     
  8. Sam1911

    Sam1911 Moderator

    Joined:
    Oct 22, 2007
    Messages:
    33,506
    Location:
    Central PA
    Yes, I'd be curious to know what you THOUGHT you were getting, and if it isn't what you thought, take it back and demand your money back. If that gun's been tinkered with much, it may or may not even be close to safe to shoot. If you think about the difference between a .357 caliber gun and a .500 caliber gun -- especially when you're talking about drilling 5-6 holes of that size in a cylinder! -- it's almost hard to imagine how you'd modify one to be the other.

    A .500 S&W revolver is enormous, and only holds 5 rounds. How many holes in your cylinder?

    A .357 Supermag cartridge has a max OAL of 1.990". A .500 S&W Mag has a max OAL of 2.250". So yeah, I'd think they'd be a "little tight" at the forcing cone. Like over a 1/4" too tight!

    Please post pics and any other info you can put together.
     
  9. The-Reaver

    The-Reaver Member

    Joined:
    Dec 27, 2010
    Messages:
    798
    Location:
    Florida
    Sounds like a handgrenade with the pin pulled & the spoon flown to me.
     
  10. CraigC
    • Contributing Member

    CraigC Member

    Joined:
    Jan 27, 2006
    Messages:
    14,258
    Location:
    West Tennessee
    Is it a five or six shot? I'd be very curious to find out exactly what's going on here. No .500's were ever produced and I don't believe I've ever heard of one converted to a custom five-shot. Although I suppose it is possible.

    I do not believe the SuperMag cylinder would be long enough for the .500S&W but it is possible that it's been converted to one of several other ~.500" cartridges. Might be a .500Linebaugh or Linebaugh Long.
     
  11. hardluk1

    hardluk1 member

    Joined:
    Mar 27, 2009
    Messages:
    4,405
    Location:
    nc mountains
    Maybe , possibly someone had it worked over to fit the 500 special cartidge. Very close to working pressures of the 480 ruger and that is with in the working pressure range of the revolver. Is it a 5 shot or 6 shot cylinder. You need to have it sent to a top end revolver smith like Bowen classics to look at what happend to see if its safe , can be saved , or junked.
     
  12. unspellable

    unspellable Member

    Joined:
    Aug 30, 2004
    Messages:
    1,744
    Location:
    Iowa
    The large frame Dan Wessons were chambered in 45 Colt & 460 Rowland.
    The SuperMag frames were chambered for 357 SuperMag, NOT to be confused with the 357 Maximum. Early production DWs were marked 357 SuperMag on one side of the barrel shroud and 357 Maximum on the other. Later production were marked 357 Maximum only even though they were still chambered for the SuperMag. The 357 Maximum has a maximum OAL of 1.900 while the 357 SuperMag has a maximum OAL of 2.125.
    The problem is that DW marked the chambering on the barrel shroud which is interchangeable. Hence a 357 SuperMag shroud will fit a 45 Colt with no problem other than being mismarked. The SuperMag has a longer ejector shroud so the large frame shrouds will not work on the SuperMag frames. I’ve suggested to DW that the caliber should be marked on the frame, not the shroud since the shrouds are interchangeable.
    My guess is that someone has put a 357 SuperMag shroud on a large frame 45 Colt. If this is the case, there is absolutely no problem shooting 45 Colt in it. The barrels have differing threads making it impossible to install the wrong barrel without cutting and rethreading the barrel.
    How about some barrel measurements on the revolver in question? And cylinder length?
     
  13. CraigC
    • Contributing Member

    CraigC Member

    Joined:
    Jan 27, 2006
    Messages:
    14,258
    Location:
    West Tennessee
    Not if it chambers .500's!

     
  14. unspellable

    unspellable Member

    Joined:
    Aug 30, 2004
    Messages:
    1,744
    Location:
    Iowa
    Mea culpa! I did not pay enough attention to the 500 S&W allegedly going part way into the chamber. That does make it a question. I know of no DW factory issue that would allow a 500 S&W to chamber part way.
     
  15. Magnuumpwr

    Magnuumpwr Member

    Joined:
    Feb 28, 2005
    Messages:
    1,032
    Location:
    Southeast Texas
    Bought the gun on an impulse. Didn't know that the barrel sleeve would fit other calibers. Looked at the gun, but failed to realize that the holes looked a little on the large size. Also, that there were only five and not six. The four inch barrel does not let the bullet in to the same depth as my S&W 500, but the ten inch barrel does. I plan to bring it to a local gunsmith to have him go over it and verify what caliber it is and if indeed it is safe to fire. Everything as far as cylinder gap is similar to my model 15 357 mag. Just inserted one of the 500 S&W rounds again, not a 500, it seems to take a rimmed cartridge of the same or very similar diameter. Also the 500 cartridge is less than a 1/4" from the end of the cylinder and the DW cylinder is roughly 1/4" shorter than my S&W 500 cylinder. I will try to get some photos posted soon.
     
  16. hardluk1

    hardluk1 member

    Joined:
    Mar 27, 2009
    Messages:
    4,405
    Location:
    nc mountains
    There is a cartidge called a 500 SPECIAL . Just like the difference in a 38sp and 357 mag. Your revolver my have been modified into that caliber. If the 500S&W fits but bottoms early that could be cartidge its ment to shoot. Don't take your pistol to some comunity collage gunsmith. Not many in this country are even skilled to do this kind of work . Atleast contact Bowen Classics and run it by them . They may want to see it or can better derect you to someone with the skill to deside if it was first done right or corect any issues it my have . If it was done by a certfied smith there should be some marks or name some where on it. Go to ammo-one and look at the soo sw mag and special differences.
     
  17. Chuck Perry

    Chuck Perry Member

    Joined:
    Dec 27, 2002
    Messages:
    895
    Location:
    Pittsburgh,PA
    Might want to check with Gary Reeder Custom as well. They offer various wildcats on the DW Super Mag guns.
     
  18. Magnuumpwr

    Magnuumpwr Member

    Joined:
    Feb 28, 2005
    Messages:
    1,032
    Location:
    Southeast Texas
    Here are a few pics.
    This shows the frame info.
    [​IMG]

    This is clear as to what it is.
    [​IMG]

    This is the complete purchase.
    [​IMG]
     
  19. Steve CT

    Steve CT Member

    Joined:
    May 19, 2011
    Messages:
    532
    Location:
    Central CT
    I have been around the "Dan Wesson World" long enough to know that there are some pretty unusual variations out there. Manufacturing moved from Monson, MA to Palmer, MA in 1992, and it seems unlikely that a five shot Large/SuperMag gun was ever made in Monson, fact a five shot Large/SuperMag is pretty much unknown. I believe this is a "one off" gun with a custom cylinder and custom barrels that are housed in the SuperMag shrouds, the 4" shrouds looks to be customized pretty heavily.
     
  20. hardluk1

    hardluk1 member

    Joined:
    Mar 27, 2009
    Messages:
    4,405
    Location:
    nc mountains
    Send that revolver to one of smiths that does this type work for a liveing to see it its save with any load. not a local run of the mill smithy. That is some seriously thin cylider walls.
     
  21. buck460XVR

    buck460XVR Member

    Joined:
    Feb 6, 2007
    Messages:
    5,814
    That's my guess, a tad shorter than a .500 S&W and a rimmed case.
     
  22. 460Shooter

    460Shooter Member

    Joined:
    Feb 12, 2011
    Messages:
    5,539
    Location:
    A cabin in the woods, on the way to nothing.
    Didn't DW make a .445 Super Mag? Could it be a gun originally chambered for that, and then reamed out to make it work for 500 specials? I sure wouldn't shoot a 500 mag out of that. The walls look a little thin for that don't they? I'm just guessing and bringing it up because noone seems to have mentioned the 445. I thought those were 6 shot revolvers though........ Anyone know?
     
  23. hardluk1

    hardluk1 member

    Joined:
    Mar 27, 2009
    Messages:
    4,405
    Location:
    nc mountains
    460 its a 5 shot now. DW did not make a 5 shot revlvers and the 44mag falls through the cyclinder. and a 500sw does fit for size but not lenght

    buck He said he had also a 1/4 of brass sticking out of the cylinder with the 500sw bottoms. Thast about right for the 500 special that is made as a down loaded cartidge like the 38sp fpr a 357mag.
     
  24. ljnowell

    ljnowell Member

    Joined:
    Jun 21, 2008
    Messages:
    6,191
    Location:
    The Peoples Republic of IL
    Except that in the 38/357 instance it was the other way around, the 357 was made as a hotter version of 38special.
     
  25. mes227

    mes227 Member

    Joined:
    Jan 12, 2011
    Messages:
    203
    Location:
    Incline Village, NV
    A lot of the wildcat work was done on early supermag frames. And the shrouds are interchangeable. So that it has a .357SuperMag shroud doesn't mean much. I have a .44Rhino (one of the wildcats) that looks a lot like yours - Monson frame, mismatched shroud, etc. Might have been an early .460 Rowland (custom built), but not sure that is large enough bore to have the smaller ctgs behave as the OP says. The bore diameter for a .460R would be 0.452". The .445SuperMag's bore would be 0.429". I've never read anything about any .500 wildcats on a DW frame. Doesn't mean they didn't exist, but if that's one it's likely one of a kind and might have some value.
     
Thread Status:
Not open for further replies.

Share This Page