Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Drilling the TSX cavity for uniformity?

Discussion in 'Handloading and Reloading' started by GJgo, Feb 27, 2011.

Thread Status:
Not open for further replies.
  1. GJgo

    GJgo Member

    Joined:
    Feb 12, 2007
    Messages:
    966
    Location:
    Western Colorado
    Got a question for you guys based on a working theory. I shoot a lot of Barnes TSX at game, as do some friends of mine. Sometimes it's a devastating wound channel & DRT, sometimes it appears to pencil right through. Different rifles, different loads, etc.. No argument there, plenty of threads arguing the subject.

    The other day I took my box of handloaded 300 WSM w/ 180 TSX and sat it on the bench. I went to my Dremel tool drawer & found my micro- drill bits. While the smallest (IIRC ~.012") would slide all the way into the cavity on the TSX hollow point with some forcing & wiggling, the largest (IIRC ~.030") would slide in a few MM & then stop- and this stop depth varied bullet to bullet. So, here's my theory- the manufacturing process of the TSX causes an inconsistent cavity from bullet to bullet, which causes inconsistent expansion on game. Some are more open, while some are darn near pinched shut.

    Since uniformity is consistency I'm toying with the idea of procuring some 1/32" drill bits (or there abouts to match the hole in the tip) and using my press to uniform the cavitys on all my TSX. What do you guys think? When these things open up I beleive there's none better. When they don't, well, a wounded Elk can run a looooong way. :cuss:
     
  2. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    47,542
    Location:
    Alabama
    Buy some Nosler Partition or Remington Core-Lokt bullets. :)

    Other than that, if you get the cavity out of round or off center even a little bit, accuracy will be affected.
     
  3. 45ACPUSER

    45ACPUSER Member

    Joined:
    May 17, 2007
    Messages:
    807
    Location:
    Minnesota
    Get tipped TSX
     
  4. GJgo

    GJgo Member

    Joined:
    Feb 12, 2007
    Messages:
    966
    Location:
    Western Colorado
    Well, I've tried the partition, the TTSX, and a few others in this particular rifle & nothing comes close to shooting as well as the 180gr TSX. So, for the sake of this thread I'm stickin' with it.

    Since I'd be using a drill press and set it to drill a fixed depth it'll be pretty uniform. Of course I'd test them to make sure the accuracy didn't suffer. Logistics aside, anyone have thoughts on the theory?
     
  5. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    47,542
    Location:
    Alabama
    The theory is excellent. The execution is going to be the hard part. It doesn't take much "wobble" to ruin accuracy.

    Let us know how it works out.
     
  6. Clark

    Clark Member

    Joined:
    Jan 3, 2003
    Messages:
    4,341
    Location:
    Where I5 meets the rain forest
    There are two schools of thought on shooting elk:
    a) TSX into the shoulder
    b) Ballistic Tip into the lungs

    I have practiced at the range with both, many times.
    I have practiced shooting mule deer many times.
    I have concluded that I am a "shoot for the lungs" man.
     
  7. kelbro

    kelbro Member

    Joined:
    Nov 11, 2007
    Messages:
    1,264
    Location:
    Desert Southwest
    Guys were reporting performing this mod a couple of years ago with good luck.
     
  8. GJgo

    GJgo Member

    Joined:
    Feb 12, 2007
    Messages:
    966
    Location:
    Western Colorado
    Thanks, Walkalong. I've got a lot loaded so I can do some drill / no drill testing for accuracy. Having used the drill press *a lot* my suspicion is that the bit will follow whatever small hole is already there, so if it was straight before it'll be straight after.

    Interesting that it's been discussed before. I did a little searching but didn't find anything on it.
     
  9. rogn

    rogn Member

    Joined:
    Sep 9, 2006
    Messages:
    287
    Minor changes to the front end of bullets will not affect accuracy. You can cut the frnt/point off a bullet at an angle withwire cutters and at 200yd there will be no practical difference in accurecy over unmoded bullets.
     
  10. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    47,542
    Location:
    Alabama
    True, mangled tips won't matter much, but we are talking about a cavity reaching into the bullet. Looking forward to the tests.
     
  11. suzukisam

    suzukisam Member

    Joined:
    Jul 8, 2009
    Messages:
    718
    what I have noticed with tsx bullets is that usually they are velocity sensitive, in that the "308" is covered by so many cartridges, that not everyone ends up liking them. for instance in a 300 whisper you may get one result, and in my 300 wby mag you'll get something else. I would be curious to know if you have the same issue repeatedly with one caliber or just a mix of results with one rifle? I know in my 243 with an 85 gr I get a pretty consistent opening every time. I'm not going to lie I never recover them. but from the pin size entrance hole and the heart soup that was inside I'm guessing they opened okay:D and have always had similar results
     
  12. GJgo

    GJgo Member

    Joined:
    Feb 12, 2007
    Messages:
    966
    Location:
    Western Colorado
    So I found some .040" (#60) drill bits & drilled a control set. They all now have a uniform cavity diameter & depth. I can tell from the feeling on the press that the overall depth is very consistent, but the diameter within the cavity seems to change. I'll report after I have a chance to test them out on paper & milk jugs vs. non-drilled counterparts. I know that this load normally will turn a jug of water into a floating cloud of water vapor...
     

    Attached Files:

  13. blarby

    blarby Member

    Joined:
    Feb 25, 2011
    Messages:
    5,144
    Location:
    Calapooia Oregon
    On a similar note, I've had great success re-boring unseated hollowpoint bullets using a cam lock trimmer to hold the bullet on one end, and the bit on the other....works just like a lathe, and you are always centered.

    This method can also be used with various jigs to make cast rounds into HP.

    Excellent thinking.
     
  14. DM~

    DM~ Member

    Joined:
    Jan 6, 2011
    Messages:
    2,263
    Location:
    upper mid west
    I guess there's nothing like spending the big money for a bullet, and then having to "fix" it before you use it! lol

    DM
     
  15. GJgo

    GJgo Member

    Joined:
    Feb 12, 2007
    Messages:
    966
    Location:
    Western Colorado
    Well, there will always be a difference between mass-produced parts & hand-fit parts. Some of us just like to tinker. :)
     
  16. bloominonion

    bloominonion Member

    Joined:
    Feb 4, 2011
    Messages:
    132
    I have drilled FMJ's into hollow point and never noticed much difference in accuracy (although it was in a pistol). Some of them were very off centered and it seemed to pose little problem, especially considering most of the accuracy comes from the spin on the bullet via rifling.
     
  17. 788Ham

    788Ham Member

    Joined:
    Sep 24, 2010
    Messages:
    3,206
    Location:
    Hills west of Denver
    I read this thread all the way through, just to follow the poster and his ideas about this bullet. My first question: You use a hollow point bullet to hunt elk? I was always schooled in the thought, you used HP's for Pd's or varmints, not caring what they looked like after the bullet hit. You stated, "Sometimes its a devastating wound channel & DRT", yes, I can only imagine what kind of a wound channel it would make through the front shoulder of an elk, total waste of meat! I guess that means you have less to worry about wrapping and freezing, to each his own!
     
  18. Brian10

    Brian10 Member

    Joined:
    Jun 19, 2008
    Messages:
    100
    788Ham, the TSX is a solid copper bullet and does not explode like their lead counterparts do. That is apples and oranges.
     
  19. suzukisam

    suzukisam Member

    Joined:
    Jul 8, 2009
    Messages:
    718
    exactly
     
  20. DM~

    DM~ Member

    Joined:
    Jan 6, 2011
    Messages:
    2,263
    Location:
    upper mid west
    Thing is, NOT all lead core bullets explode!

    DM
     
  21. GJgo

    GJgo Member

    Joined:
    Feb 12, 2007
    Messages:
    966
    Location:
    Western Colorado
    Time for an update, I've done some testing.

    Accuracy. I zeroed my rifle at 200 yds & ran a couple cold-bore groups with standard & drilled rounds, no appreciable difference. Same basic POI & groups around an inch off a good rest.

    Milk jug test. Both drilled & standard rounds turn milk jugs & watermelon into vapor. Far more dramatic than the same test w/ a cup and core bullet, which just turns them into chunks.

    Test on game. I've never seen a TSX recovered on a deer or elk broadside shot, I load for mine & a couple friends. This year we recovered a drilled round (w/ textbook X expansion) in the off-side hide of a cow elk after passing through a rib & lungs. The shot was ~275 yds. The follow-up round, which was standard & not drilled, went through the paunch & liver and was a complete pass through as usual.

    Yes this is only one example, but I'm confident that the drilling did help to initiate expansion that would not have been as dramatic otherwise. That's the good news. The only bad thing I could think of is that if you had to trail the animal, 2 holes would be better than one..
     
    Last edited: Nov 20, 2011
  22. 918v

    918v Member

    Joined:
    Mar 16, 2006
    Messages:
    3,931
    Good Job!
     
  23. rogn

    rogn Member

    Joined:
    Sep 9, 2006
    Messages:
    287
    TSX

    Damage or lack of symetry in the front of a bullet will have little effect on short (300yd or less)range accuracy. Youncan cut off the front end of a soft point with wirecutters and still shoot sub inch groups at a 100. Ive shot 90# whitetails and the wound channel with aTSX under 3000fps will give a nice 1-2" exit wound and minimal meat damage, up the velocity and bets are off. I shot a 100# bushbuck and an 1800# eland with the same 160gr 7mm TSX and lost minimal meat with either. The exit on the bushbuck was abit over an inch and none of the shots on the eland were passthrus. Ive never had to drill the TSXs and have always had picture perfect results, and little meat loss. On the other hand Ive shot some of our small whitetails with the YSX over 3300 and bloodshot meat is staggering. I dont use the super light bullets anymore, an exception is say a 120 TTSX in 7-08 loaded to just short of 3000. This is a good load for young or smallframed shooters.
     
  24. GJgo

    GJgo Member

    Joined:
    Feb 12, 2007
    Messages:
    966
    Location:
    Western Colorado
    I did some drilling today to start getting ready (mentally!) for hunting season. Same lot of 180gr TSX I've had loaded up, using the .040" drill bits I mentioned earlier. After drilling 30 or so bullets I noticed a couple things.

    First, the tip of the hollow point extends in only about .040" or so before my drill bit stops. Next, on some bullets it only takes mild pressure for the bit to releive this "pinch", but on the majority it takes a bit more pressure for the bit to drill through. This tells me that the amount of pinch is a little inconsistent. Third, once the pinch is cleared the bit can clean out the hollowpoint pretty easily down to oh a quarter inch or so which I think will solve the problem & allow the hydraulic forces to more consistently open the round.

    In general I've read that speed is key with TSX & I tend to agree. I'm just thinking that this mod may help to hedge your bets on a long shot where the speed drops down or some other unexplained factor happens. Hopefully I'll get more chances to test it out this fall. :)
     
  25. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    I've killed a lot of big game with a variety of bullets and the Speer Hot core has performed the most consistent in every manner. I shot a bull elk with a 130 gr. one from a .270 win. and the shot placement was horrible, straight up the spine. The bullet traveled up the back bone through ever single vertebra and stopped at the base of the neck. When I removed it, it still had over 90% of it's weight and was nicely mushroomed.

    With shoulder shots my bullets have the normal small entry wound, but with a near dinner plate sized exit wound. The Nosler Partition has performed quite well also.

    GS
     
Thread Status:
Not open for further replies.

Share This Page