Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

DSA STG-58 Carbine vs. Well-built Imbel FAL Carbine?

Discussion in 'Rifle Country' started by hartzpad, Oct 25, 2005.

Thread Status:
Not open for further replies.
  1. hartzpad

    hartzpad Member

    Joined:
    May 12, 2004
    Messages:
    445
    Location:
    Utah
    So...Which of these two carbines is better for the money? I've seen some seemingly well-built Imbel FAL carbines for sale for $650 while the DSA STG-58 carbines go for around $1000. I know that both are built from used/surplus kits so the DSA is not a brand new U.S. made barrel, etc. What does the DSA give you that a well-built Imbel does not for $350 more, just a U.S. built receiver? I guess it is just the assurance that your rifle will run out of the box and comes with a warranty? It seems to me that a well-built Imbel carbine kit should be just as good as a DSA, am I mistaken?
     
  2. Coronach

    Coronach Moderator Emeritus

    Joined:
    Dec 20, 2002
    Messages:
    11,109
    Assuming you get a well-built Imbel parts gun that runs fine and is nicely finsihed, nothing. You're money ahead getting the Imbel. If you have a line on a good plumber who will stand by his work, and can beat DSA's prices, go for it.

    Of course, the DSA will be more likely to run right out-of-box than your average parts gun, more likely to have better fit and finish, and if it doesn't run you have DSA's lifetime warranty.

    If you have a line on a good guy, go for it. If not, I'd go DSA.

    JMO,
    Mike
     
  3. Coronach

    Coronach Moderator Emeritus

    Joined:
    Dec 20, 2002
    Messages:
    11,109
    BTW, you should be able to get into a DSA STG-58 for well under $1,000, unless the prices have gone up. Dealer cost was floating at about $800-ish, so I would not be surprised to find new ones for $900 and under, used for less. Though, others would know more about prices than me.

    Mike
     
  4. iamkris

    iamkris Member

    Joined:
    Jan 6, 2003
    Messages:
    2,839
    Location:
    My own little slice of Purgatory
    If it is a spanking new parts kit and the builder is a craftsman, probably not a lot.

    That said, I'd bet that my Steyr "parts kit" for my DSA StG58A was either New, Unissued or test-fired only. It was absolutely pristine (well, it was about 2000 rounds ago) and the DSA receiver was beautifully made.
     
  5. Redlg155

    Redlg155 Member

    Joined:
    Dec 25, 2002
    Messages:
    2,724
    Location:
    NW Florida
    DSA STGs are very nice and might just get another one to replace the one I sold.

    With a DSA you are guranteed the required US parts count required by law as well as a warranty on the rifle. The finish and quality of the one I had was excellent and even though it was a cabine model, it ran 100 percent right out of the box.

    With the DSA you will also have a guranteed good resale value. If you monitor the for sale boards you will see that folks selling DSAs have no problem, while others selling "home built" or rifles built from lesser known folks have a harder time selling.

    Is it worth the extra? ..To me, yes.
     
  6. idakfan

    idakfan Member

    Joined:
    Sep 13, 2005
    Messages:
    141
    Location:
    Central Idaho
    DSA all the way.

    STG58s sell well under $1,000.00, that is unless you want to get price-gouged.

    DSA - Made in USA
    IMBEL - Made in Brazil

    Any questions?
     
Thread Status:
Not open for further replies.

Share This Page