Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Fluxing

Discussion in 'Handloading and Reloading' started by blarby, Sep 23, 2012.

Thread Status:
Not open for further replies.
  1. blarby

    blarby Member

    Joined:
    Feb 25, 2011
    Messages:
    5,144
    Location:
    Calapooia Oregon
    I've just been using motor oil for fluxing alloys for bullet casting.

    It seems to work pretty well.


    Just wondering if anybody has found anything thats cheaper, or that has some magical properties I've been missing this whole time ?
     
  2. JohnM

    JohnM Member

    Joined:
    Jan 27, 2011
    Messages:
    1,640
    Location:
    Down there by the river
    Sawdust
     
  3. saltydog452

    saltydog452 Member

    Joined:
    Aug 1, 2004
    Messages:
    1,705
    Bottom pour or dipper?
     
  4. 918v

    918v Member

    Joined:
    Mar 16, 2006
    Messages:
    3,931
    Sawdust works best.
     
  5. ReloaderFred

    ReloaderFred Member

    Joined:
    Apr 28, 2005
    Messages:
    5,825
    Location:
    Oregon Coast
    I've tried everything, and sawdust works best. If you use hardwoods, it smells better, too. The only drawback is there's a lot of smoke as it's charing. You let it go until it forms dark ash, as it's the carbon that does the fluxing. Then stir your alloy. If you leave a layer of the ash on top of the alloy while it's molten, it slows down the oxidation, too.

    There are a few exotic woods you want to stay away from, since they emit poisonous toxins when burned, but they're mostly from the tropics. Poison oak would also be a bad choice.............

    Pine and oak work well, as well as alder and maple shavings or sawdust. If you do any woodworking at all, it's free. You can also sometimes get a bag of wood pellets for pellet stoves that's gotten wet. I've purchased a 40 pound bag for a dollar, since they can't be used for a pellet stove once the pellets have gotten wet and reverted back to coarse sawdust. The store is usually just glad to be rid of them.

    Hope this helps.

    Fred
     
  6. FROGO207

    FROGO207 Member

    Joined:
    Dec 7, 2008
    Messages:
    6,302
    Location:
    Mount Desert Island Maine
    Yep I cut some hard wood (oak) stair treads to size and that sawdust was great for fluxing the lead. I guess I will just cut the small ends up to make more sawdust till they are used up.:) Have you any woodworking shops nearby. I would think that fine pet shavings (bedding) would work well also.
     
  7. blarby

    blarby Member

    Joined:
    Feb 25, 2011
    Messages:
    5,144
    Location:
    Calapooia Oregon
    Well, I get used motor oil for free too, so I guess its about the same price you guys pay for sawdust.

    It has plenty of carbon.........
     
  8. blarby

    blarby Member

    Joined:
    Feb 25, 2011
    Messages:
    5,144
    Location:
    Calapooia Oregon
    Bottom pour- not sure how that will help though - I alloy and make ingots.

    I'd never do all that mixing and fluxing and BLEH in my production furnace.
     
  9. JohnM

    JohnM Member

    Joined:
    Jan 27, 2011
    Messages:
    1,640
    Location:
    Down there by the river
    Some people are afraid of sawdust in a bottom pour because of the chance of a plugged spout.
    Baloney really.
    I smelt in a big old cast iron pot and don't worry about a few bits of carbon stuck to the sides or bottom.
    I use a stainless pot for casting and scrape the sides and bottom with an old metal spoon to be sure everything comes to the top.
    That's all it takes.
    Sawdust, wood chips work great as a flux, doesn't stink as bad as old oil.
    I always have a lot of it around anyway.
     
  10. GP100man

    GP100man Member

    Joined:
    Mar 16, 2007
    Messages:
    1,749
    Location:
    Tabor City, NC.
    I flux with parrafin & stir with a paint stik , make sure it`s completely dry before stirring .

    I use sawdust in the smelting pot .
     
  11. rsrocket1

    rsrocket1 Member

    Joined:
    May 20, 2010
    Messages:
    1,276
    Location:
    Sacramento, CA
    Sawdust, charcoal briquets (smashed into a powder with a hammer), old remnants of used up candles. They all work, but I do like the sawdust and charcoal as it leaves a layer of ash on top that prevents oxidizing of the alloy.
     
  12. Kp321

    Kp321 Member

    Joined:
    Jul 12, 2012
    Messages:
    1,007
    Location:
    West Texas
    I have used lots of things but never motor oil! Wax, sawdust, bullet lube, powdered rosin, but the commercial product Marvelux is the best. No smoke, no mess and ten dollar's worth lasts years.
     
Thread Status:
Not open for further replies.

Share This Page