Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Gas Check bullets with out Gas Checks?

Discussion in 'Handloading and Reloading' started by TooManyToys, Mar 12, 2013.

Thread Status:
Not open for further replies.
  1. TooManyToys

    TooManyToys Member

    Joined:
    Feb 12, 2011
    Messages:
    187
    My question is this;
    Do cast Gas Check style bullets shoot ok without a gas check installed?

    The reason I ask is this, a while back aquired a nice bullet mold,
    (158g 38/357 HP) that takes a gas check.
    My first reaction was to sell it because I wasn't interested in messing around with the availability and cost of gas checks.
    But,.... now I'm having 2nd thoughts about selling it if they would shoot just fine without a gas check installed. I'm gussing some of you out there must have tried this before??
    Do they shoot much, if any dirrerent than a regular bevel based cast bullet?
     
  2. Reefinmike

    Reefinmike Member

    Joined:
    Apr 17, 2012
    Messages:
    1,574
    Location:
    SW Ohio
    I cant see why they wouldnt shoot well. pretty sure there are a couple guys on castboolits selling punches to make your own gas checks out of your beer cans.
     
  3. TooManyToys

    TooManyToys Member

    Joined:
    Feb 12, 2011
    Messages:
    187
    Thats a thought too. Do you have a link?
     
  4. Reefinmike

    Reefinmike Member

    Joined:
    Apr 17, 2012
    Messages:
    1,574
    Location:
    SW Ohio
  5. BruceB

    BruceB Member

    Joined:
    Jun 26, 2004
    Messages:
    718
    Location:
    nevada
    There is an entire FORUM on gas-checks at Cast Boolits. More info than you can imagine!
     
  6. twice barrel

    twice barrel Member

    Joined:
    Oct 21, 2009
    Messages:
    226
    They usually shoot just fine. The alloy, fit, and velocity will determine whether or not you need the gas check. Back when I cast my own bullets I quit fiddling with the gas checks when I found they made no difference.

    TB
     
  7. GP100man

    GP100man Member

    Joined:
    Mar 16, 2007
    Messages:
    1,749
    Location:
    Tabor City, NC.
    In my exp with the 38/357 GC boolits do fine until ya push the gas then grouping will open .

    If it`s a steel mold (Lyman 358156??) contact Buckshot over on CastBoolits.com ,he does a fine job of removing the GC shank !!

    Here`s a pic of his work , top shelf machinist !!!

    102_0583.jpg
     
  8. wgaynor

    wgaynor Member

    Joined:
    Nov 9, 2009
    Messages:
    903
    Location:
    Western Kentucky
    I shoot them that way without problems.
     
  9. TooManyToys

    TooManyToys Member

    Joined:
    Feb 12, 2011
    Messages:
    187
    It is LEE Mold that isn't available anymore.
    For those who haven't seen a mold like this, here are some pictures.
     

    Attached Files:

  10. homatok

    homatok Member

    Joined:
    Mar 17, 2012
    Messages:
    333
    To answer the op's question----yes you can. How successful you will be depends on your gun and your load. Keep pressures low and use a well fitted bullet and see for yourself.
     
  11. GooseGestapo

    GooseGestapo Member

    Joined:
    Jan 6, 2003
    Messages:
    3,391
    Location:
    W.GA
    I have the exact same mould.
    Mine will shoot decent w/o gaschecks if loaded to .38spl loads. I lube them with Lee Alox Tumble Lube. Also, I run them through a .357" sizer to "round" them out. I also often get a bit of "flashing" at the hollow-point punch area.
    It's got "issues". Its slightly under sized. The shank for the gas checks is under sized and gas-checks won't fit well unless bullet is really pushed down hard in a Lyman 450 sizer w/flat punch.

    There's reasons that Lee discontinued it. But, I'd keep it. Get the 158gr SWC-TL mould and the .358" sizer die and use them with the TL. You can run these up as high as 14.0gr of #2400 in .357magnum loads with good results. If you have a Lyman 450 sizer, you can even swage a gas-check onto the base of the 158swc-tl and "make" it a GC bullet.

    With a gas-check (hollow point mould), it also dosen't shoot well until loads are up around 14.0gr of #2400. There, it shoots well. It takes a good "whop" to bump it up to bore cylinder throat diameter in a revolver.
     
  12. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Yes you can.

    When you think about it real hard?

    A GC bullet without a GC isn't all that much different then those bevel-base cast bullets everyone sells anymore.

    rc
     
  13. blarby

    blarby Member

    Joined:
    Feb 25, 2011
    Messages:
    5,144
    Location:
    Calapooia Oregon
    ^^^^^^^^^^^^


    My experience with shooting bullets meant for a gas check without the check has been overwhelmingly positive.

    My 44 HP bullets, when machine lubed, use that GC spot for an extra lube ring- and they shoot fantastic.
     
  14. TooManyToys

    TooManyToys Member

    Joined:
    Feb 12, 2011
    Messages:
    187
    Thanks to all !
    Your responces are comfirming what I thought would probably be the case, that a gas check bullet will shoot just fine with or without a gas check installed.

    GooseGestapo,.... thanks for sharing your experiances being a owner of the same mold!
     
    Last edited: Mar 13, 2013
  15. BruceB

    BruceB Member

    Joined:
    Jun 26, 2004
    Messages:
    718
    Location:
    nevada
    I've fired a lot more 358156 bullets WITHOUT gas checks, than I have WITH gas checks..... no problems.

    The same applies to 429244 in .44 Magnums....again, no problems.

    In rifles, however, direct side-by-side grouping tests showed conclusively that accuracy was FAR better and more consistent WITH gas checks installed, even at very low velocities. By "far better", i mean differences of , say, one- or two-inch groups WITH gaschecks at 100 yards as opposed to a FOOT or more for a 100-yard 'group' without checks in the same load. No contest, in other words.
     
  16. homatok

    homatok Member

    Joined:
    Mar 17, 2012
    Messages:
    333
    Bullet design/style with respect to weight distribution can also sometimes play a part.
     
Thread Status:
Not open for further replies.

Share This Page