Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

"Go To" for .270 accuracy?

Discussion in 'Rifle Country' started by DHaught, Nov 20, 2010.

Thread Status:
Not open for further replies.
  1. DHaught

    DHaught Member

    Joined:
    Nov 7, 2009
    Messages:
    14
    Location:
    NC
    Couldn't think of a better title..
    Anyway, what is considered the standard bearer for .270 win. for accuracy in a factory load? I know all guns are different and you need to try different loads but what is considered the "Go To" round for factory accuracy?
    It seems like everyone leans towards the 168gr. Federal GMM in the .308 world but what is it's analog in .270?
     
  2. Fremmer

    Fremmer Member

    Joined:
    Oct 9, 2009
    Messages:
    2,284
    What about the Remington Core-lokt? Those usually shoot pretty well through most rifles.

    I guess it really depends on the individual rifle, though.
     
  3. nathan

    nathan Member

    Joined:
    Feb 4, 2003
    Messages:
    5,067
    I ve shot a Howa 1500 with the factory scope using Remington 130 gr SP corelokts. It was 1.3 inch grp at 100 yds.
     
  4. jbkebert

    jbkebert Member

    Joined:
    Jan 30, 2009
    Messages:
    2,599
    Location:
    Kansas
    Hornady custom 130 grain SST. Does as well through two of my rifles as any handload I have ever produced. Same goes with the .243 95 grain SST will print a dime 5 shot group at 100 yards through my Tikka or my Encore pro-hunter.
     
  5. Geno
    • Contributing Member

    Geno Member

    Joined:
    Jun 11, 2005
    Messages:
    14,978
    I have had consistently good accuracy with Federal Premium 130 grain.

    Geno
     
  6. Yarddog

    Yarddog Member

    Joined:
    Jan 28, 2010
    Messages:
    503
    Location:
    FL.--There's a Gator in the bushes & She's callin
    130gr is most accurate in the rifles I had in .270 cal ; )
    Y/D
     
  7. browningguy

    browningguy Member

    Joined:
    Jul 21, 2004
    Messages:
    4,577
    Location:
    Houston, TX
    I'm with JB, if it won't shoot the factory SST load at least decent it probably won't shoot anything. In my .270, 308 and 30-06 they are consistantly the best factory loads.
     
  8. Justin Holder

    Justin Holder Member

    Joined:
    Apr 24, 2010
    Messages:
    485
    I have to go with the Winchester 130gr. Power Point load.
     
  9. blitzen

    blitzen Member

    Joined:
    Oct 2, 2006
    Messages:
    388
    Location:
    Alaska
    My Browning bolt action would really only shoot the Hornady Custom 140gr boat tails well. I could bet it to shoot an honest inch at 100. All other factory rounds for me were in the 1.5 to 2 inch range.
     
  10. PT1911

    PT1911 Member

    Joined:
    Feb 27, 2009
    Messages:
    3,139
    Location:
    alabama
    I have a Weatherby VGX delux in 270 that shoots Federal Power Shoks into an inch or just over at 100 yds consistently and will do the same with Remington Core Lokts.... That friends, is a keeper.
     
  11. pbrktrt

    pbrktrt Member

    Joined:
    Jan 15, 2008
    Messages:
    329
    My Vanguard loves the Hornady 130gr & 140gr SST. The Superformance load is actually better than the Custom I used to shoot.
     
  12. jbkebert

    jbkebert Member

    Joined:
    Jan 30, 2009
    Messages:
    2,599
    Location:
    Kansas
    I am interested in trying the superformace ammo. My son received three boxes of it in .270 for his birthday. Talk about having a cool uncle.
     
  13. CowboyTim

    CowboyTim Member

    Joined:
    Nov 23, 2010
    Messages:
    75
    Location:
    Cazenovia, WI
    Fed premium, 150gr sierra
     
  14. GooseGestapo

    GooseGestapo Member

    Joined:
    Jan 6, 2003
    Messages:
    3,274
    Location:
    W.GA
    My vote is for the Federal "Premium" with the 130gr Sierra bullets. Second would be the same with 150gr Sierra bullets. Also accurate are the Remington and other's with the "ballistic tip" type bullets.

    I've loaded both the Sierra and Nosler B.T.'s for friends .270 and they've all been superlative accurate when loading a 130gr bullet over either 54.0gr of IMR4350, 58.0gr of H4831, or 54.0gr of H414.
     
  15. Horsemany

    Horsemany Member

    Joined:
    Jan 6, 2007
    Messages:
    1,320
    Location:
    Midwest
    130 gr Fed. Fusions were slightly under .5" in my Browning X-Bolt. Couldn't top it with my best handloads.
     
  16. JR47

    JR47 Member

    Joined:
    Aug 16, 2008
    Messages:
    1,414
    Location:
    N. Georgia
    Oddly enough, my older Savage 110GL prefers the 130 gr. Remington Bronze Point loads.
     
  17. mes228

    mes228 Member

    Joined:
    Feb 21, 2006
    Messages:
    317
    Rifle

    It's the rifle not the ammo. If the rifle is built "right" it will throw the same grain bullet configuration to pretty much the same place. With at least acceptable accuracy. The change of various cartridge manufactures should "fine tune" but not change impact several inches. I've searched for an accurate factory rifle for quite a while and purchased several new ones. All were a great disappointment in actual accuracy though some beautiful. The search ended with the very low cost Thompson Contender Venture in .270 caliber. It will throw any Walmart 130 grain ammo into about an inch, and the Federals into 1/2 inch if you are very good. After throwing away several new Remingtons, Rugers, Savage, and misc. others - the T/C Venture is the real deal. All results were from a bench using a Lead Sled. Most new rifles are a JOKE in accuracy, totally contrary to what the gun magazines write. I believe it's the barrels on today's rifles. you will read on the net statements like "you must break the barrel in" or "accuracy improves after 200-300 rounds". This is total BS!! A new rifle should be acceptably accurate out of the box. Not after $300 of ammo and hours or range time. The CZ's and T/C's will shoot from the FIRST round. Just my experience - but it's the truth not lies as many magazine articles are.
     
  18. Moose23

    Moose23 Member

    Joined:
    Oct 21, 2009
    Messages:
    66
    Location:
    Sandy Bottom, NC
    Hornady 130 grain SST's from my early 80's Model 70. 3 shots covered by a nickel at 100yds.
     
  19. porscheboy

    porscheboy Member

    Joined:
    Nov 26, 2008
    Messages:
    65
    Location:
    New Prague, Minnesota
    130 grain Winchester/Nosler Ballistic silvertips. With 53 grains of 4350. quarter inch groups with factory remington 700 sps.
     
  20. DirtyHarry31

    DirtyHarry31 Member

    Joined:
    Sep 15, 2009
    Messages:
    80
    Location:
    North of Philly, Pa.
    My Remington Sendero in 270 Win can hold .5-.38 groups @ 100 yrds with the "blue" box Federal ammo. I have found 130 gr Federal Factory ammo to shoot very consistently.
     
  21. ssmlr3

    ssmlr3 Member

    Joined:
    Nov 2, 2010
    Messages:
    11
    accuracy

    I recently purchased a Panther LR338L. I sighted my rifle today and it shot fantastic. I shot 9 rounds with cleaning the gun after each round. Then 3 rounds and then cleaned the barrel. On the 17,18,19 shots I got this group. It measures inside .567" and the outside of 1.034. I just cant believe a lightweight, 18" barreled gun could be such a shooter. It was 50 degrees and sunny at 8000’ using 200 grain Federal Soft Point. I had about 3 to 5 mph cross wind from left to right. I used a Vortex 3-9-40 scope.
     
  22. NCsmitty

    NCsmitty Member

    Joined:
    Jun 29, 2008
    Messages:
    5,325
    Location:
    North Carolina
    Welcome to THR, ssmlr3.

    That was pretty good shooting, but I would expect that in a $1100+ rifle. I take it that you were using factory ammo.
    If you get a chance, post some pics of your rifle and targets. Just put your pics on the computer and go to the advanced posting and download the pics to your post.




    NCsmitty
     
  23. ssmlr3

    ssmlr3 Member

    Joined:
    Nov 2, 2010
    Messages:
    11
    DPMS 338 federal pics

    here are some pics from yesterday. Yes Facotry Federal 200 gr softpoint.
     

    Attached Files:

Thread Status:
Not open for further replies.

Share This Page