Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Help with 77gr SMK load please

Discussion in 'Handloading and Reloading' started by 9sigman45, Dec 13, 2007.

Thread Status:
Not open for further replies.
  1. 9sigman45

    9sigman45 Member

    Joined:
    Nov 5, 2007
    Messages:
    11
    Location:
    NC
    OK guys, I just started reloading for .223 about six months ago. So far I've had good success with 69gr SMK atop 22.5gr of H335 with an OAL of 2.256. Next I plan to try the 77 gr SMK bullet. Using H335 (I got alot of it onhand:evil:), give me an idea of where to start (i.e. the powder charge and OAL).

    Thanks to all, and MERRY CHRISTMAS!!!!!!!!
     
  2. armoredman

    armoredman Member

    Joined:
    Nov 19, 2003
    Messages:
    16,213
    Location:
    proud to be in AZ
    In what? I reload for a Mini-14, with H-4895.
     
  3. 9sigman45

    9sigman45 Member

    Joined:
    Nov 5, 2007
    Messages:
    11
    Location:
    NC
    Good question, sorry about that.
    Right now I'm working up loads for my scoped AR. It has a WOP stainless Kreiger with what I think is a pretty tight chamber. With a Hornady OAL tool, the 77gr SMK touches the lands at 2.350
    Thanks

    [​IMG]
     
  4. NuJudge

    NuJudge Member

    Joined:
    May 20, 2006
    Messages:
    748
    Location:
    SE Michigan
    The beauty of the 77gr bullet is one can load it to fit in the magazine, and the bullet should be well short of the lands doing this. I've always set the OAL according to the magazine's requirements. Sierra bullets do not vary in terms of the bullet base, diameter, and ogive dimensions, but they vary significantly in terms of bullet length because of the very tip. Some shooters are going to a lot of trouble to trim the very tips uniformly (Meplat trimmers). Once you have something that works, be consistent.

    There are a lot of Service Rifle shooters using that bullet. I don't believe there are a lot of them using that powder (H335). The results I got were ok, but everybody reports different results with the AR. There are some that use a similar bulk powder, WCC 846. Different shooters report on what works for them in these sites/threads (registration may be necessary), as well as some data links:

    Look under "Reloading Stuph" in upper left:
    http://radomski.us/njhp/

    http://www.nationalmatch.us/forums/index.php?showtopic=539&hl=H335

    http://www.nationalmatch.us/forums/index.php?showtopic=448&hl=H335

    http://www.sierrabullets.com/index.cfm?section=techservice&page=xring&volume=6&issue=3

    http://accurateshooter.net/Downloads/sierra223ar.pdf

    http://www.gswagner.com/bigreloading/components/powderburnrate.html
     
  5. ocabj

    ocabj Member

    Joined:
    Jan 22, 2003
    Messages:
    2,383
    Location:
    Riverside, CA
    If you're going to seat your bullets long for that gun, you may as well go with a VLD design and/or an 80gr+ bullet.

    I'm betting your WOP Krieger barrels at least 1:7.7 or faster. I think you'll get better wind drift performance with a Berger 80gr VLD. The Hornady A-Max 75 and 80gr bullets are the least expensive of the "long line" bullets. Sierra MK 80gr are the base line standard. Berger should have their new 82gr BT out.

    I've got a summary of a report on the Berger 82gr BT (along with the 80gr BT; both non-VLDs, but the 80gr was not put into production):
    http://www.inlandshooters.net/index.php?contentid=69
     
Thread Status:
Not open for further replies.

Share This Page