Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Homemade wooden stocks

Discussion in 'Rifle Country' started by P.B.Walsh, Aug 31, 2009.

Thread Status:
Not open for further replies.
  1. P.B.Walsh

    P.B.Walsh Member

    Joined:
    Mar 11, 2009
    Messages:
    2,287
    Location:
    Tuscaloosa,Alabama
    How difficult would it be to make a wooden stock out of a blank?

    What kind of tools would you need?

    I am seriously thinking about this as a project for a Rem. 700.

    How much are baisic wooden blanks (nothing fancy, just some baisic wood)?

    This stock would be similar to a 1903A4/tube gun stock hybrid, with rails on 12, 9, 6, and 3 o'clock positions (I figure I could screw some on there like you would a scope base).

    Any advice would be GREATLY appreciated.

    Thanks,
    P.B.Walsh
     
  2. ArmedBear

    ArmedBear Member

    Joined:
    Sep 8, 2005
    Messages:
    23,171
    I just saw a nice stock made from a plank, not a blank, yesterday.

    It's possible. The guy said he'd never do it again, though.:)

    And he's a very skilled machinist, and has made a good number of stocks from blanks.

    He's also retired and has a lot of time.

    I'd go for 90% inletted, myself.
     
  3. Acera

    Acera Member

    Joined:
    May 26, 2007
    Messages:
    2,894
    Location:
    Free State of Texas
  4. P.B.Walsh

    P.B.Walsh Member

    Joined:
    Mar 11, 2009
    Messages:
    2,287
    Location:
    Tuscaloosa,Alabama
    WOW! That just gave me an idea to use a MN instead of a brand new Rem. 700. Mabey I could find a cheap used '700.

    Please keep up the advice! :)

    Thanks,
    P.B.Walsh
     
  5. P.B.Walsh

    P.B.Walsh Member

    Joined:
    Mar 11, 2009
    Messages:
    2,287
    Location:
    Tuscaloosa,Alabama
    Bump.....
     
  6. Cosmoline

    Cosmoline Member

    Joined:
    Dec 29, 2002
    Messages:
    23,648
    Location:
    Los Anchorage
    If you don't care how bad it looks, how it fits or how it shoots then it's not too difficult. You can make one that roughly functions with a chainsaw and some wood screws. If you're seriously looking for something better than a factory would make, then you need good chisels and all the other tools in addition to usual shop equipment.
     
  7. P.B.Walsh

    P.B.Walsh Member

    Joined:
    Mar 11, 2009
    Messages:
    2,287
    Location:
    Tuscaloosa,Alabama
    Yes I do care a lot about function and looks, what baisic shop tools are you talking about, I dont have a lot of stuff (if any).

    Thanks,
    P.B.Walsh
     
  8. paintballdude902

    paintballdude902 Member

    Joined:
    Jun 30, 2007
    Messages:
    2,872
    if i could get a hunk of wood that was inletted i would shape my own but i dont have the patience to do inletting
     
  9. P.B.Walsh

    P.B.Walsh Member

    Joined:
    Mar 11, 2009
    Messages:
    2,287
    Location:
    Tuscaloosa,Alabama
    Does anyone know where I could get an inleted block?

    Thanks,
    P.B.Walsh
     
  10. BCRider

    BCRider Member

    Joined:
    Nov 15, 2008
    Messages:
    7,715
    Location:
    Pacific North"Wet" Coast of Canada
    If you're after a painted finish then copy more or less what that guy did in the thread in the link above. If you're keen on a nice wood stock that looks like wood then you're in for a rough ride as only the best work will be sufficient. For example I cringed when I saw the wood screws and filler on that other project. The camo painting saved the day. I've done woodworking for years now and when I did a bit of stock work a while back it took pretty much every tool I had at some point. At the very least you're going to need the following AND the skills to use them correctly. The tools you can buy, the skill comes a lot harder. It's not rocket science but there's lessons to be learned that come with time and practice.

    -A band saw or at least a decent jigsaw to cut out the initial shape.
    -A router and ball or "cove" bits to do the initial inletting. And a router table to go with it will make for an easier time. This will be used for the rough inletting.
    -A large, medium and smaller size half round coarse file. These must be new and only used for wood. Use them on steel even once and they'll be too dull for wood from that time on.
    -A drill press and some forstner bits for roughing in the mortise for the action and trigger. You may think that a hand drill will do. But it's hellishly hard to drill all the stuff you need to do with the degree of control needed to do a nice job. A drill press makes this sort of thing practical.
    -A few chisels for cleaning up the mortise and other small details. 1/4, 3/8 and 1/2 is a good starter set.
    -Sandpaper. Most of the roughing work will be done with the files but you'll still want some 80, 120 and 240 grit paper.

    Now this may seem like a lot of tools but remember that in your case you're needing to replace at least some skills with technology. Yes a master woodworker could do the whole thing with maybe 7 or 8 handtools. But he has the experience to do this and the knowledge on how to save himself much work while still ensuring accuracy. You don't have that knowledge yet. If you did you wouldn't be asking the question you did.

    Chisels- Don't skimp here. Get good quality stuff so it lasts and holds a good edge. And you'll need sharpenng stones for them since they do not come properly sharpened. If you think they are good as they come from the packages then you've clearly got a lot to learn. When I can shave hairs from my forearm cleanly and with no pulling sensation THEN they are sharp enough.

    Sandpaper- use the coarser grits with a support block for most of your work. Only use the paper on it's own on fully rounded areas. Otherwise the shapes will suffer. Only with the 240 for the final smoothing can you use it without a support block. And change the paper often. If you're not using the paper on a block then fold it like this for firmness. Here's some sandpaper trick links...

    http://www.ronhazelton.com/archives/tips/Tips-SandpaperCutter.shtm
    http://www.woodzone.com/tips/folding_sandpaper.htm

    With this last trick on folding I suggest cutting the paper into 1/4's and then doing the fold and tear then fold trick shown with the 1/4 sheet. A full sheet folded like that is far too big to use properley on a project such as a gunstock.

    I'd suggest go for a slightly loose fit and glass or epoxy bed it. This is far easier than trying to do a precision inletting job. Especially for a newbie.

    And last but definetly not least. Do a practice stock using some cheap lumberyard wood first. If you don't have success the first time then it's no biggie. You just ruined maybe a couple of bucks of wood. So try again. When you can do one in the cheap wood successfully then go buy the more expensive hardwood of your choice. For someone that's never done this sort of thing before this trial run on the cheap stuff method is the only way that makes sense. Otherwise you're going to ruin a nice bit of whatever that's going to cost anywhere from $40 to $400 depending on what wood and class of figure it has that you get.

    Those 90% finished stocks are sounding a LOT better at this point I'll bet.... :D From a money standpoint it makes zero sense for you to make your own stock. It's going to cost big bucks to get teh stuff to let you make one. But if you're looking for a way to get into wood working then that's different. You're still taking an overly big bite to my thinking though.
     
  11. P.B.Walsh

    P.B.Walsh Member

    Joined:
    Mar 11, 2009
    Messages:
    2,287
    Location:
    Tuscaloosa,Alabama
    Wow, thats a lot of stuff that I had no clue about!! I'll definately read that a few more times.

    Where can you find a 90% inlet (just the action area)? I REALLY want to design the entire outside.

    Thanks, and please keep up the great advice,
    P.B.Walsh
     
  12. BCRider

    BCRider Member

    Joined:
    Nov 15, 2008
    Messages:
    7,715
    Location:
    Pacific North"Wet" Coast of Canada
    Can't help you on that count other than to email some of the outfits that make stocks and work out a price on a blank with just the action milling done. Their stocks are likely done in a duplicating rig so to do just the inletting and action mortise work they would have to just do that part only. Or if it's a multi stock duplicator then they'd do all the inletting and action mortise work first, lift your stock out of its station and then proceed with the others. The issue would be if they are done on a CNC machine. In that case it may not be worth their time to do up a stripped down set of inletting/mortising only code. I'm sure they'll tell you soon enough either "no" or quote a price that's as good as saying "no" :D
     
  13. Sav .250

    Sav .250 Member

    Joined:
    Jun 5, 2007
    Messages:
    3,345
    Location:
    Central Fla
    I have no talent for that......... or desire as well. :)
     
  14. P.B.Walsh

    P.B.Walsh Member

    Joined:
    Mar 11, 2009
    Messages:
    2,287
    Location:
    Tuscaloosa,Alabama
    Good idea.

    Thanks to all,
    P.B.Walsh
     
Thread Status:
Not open for further replies.

Share This Page