Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

How Do You Calculate LOP?

Discussion in 'Rifle Country' started by rhubarb, Dec 28, 2006.

Thread Status:
Not open for further replies.
  1. rhubarb

    rhubarb Member

    Joined:
    May 28, 2005
    Messages:
    765
    Location:
    South Texas
    I plan to buy a cheap used .22 bolt gun for my 4 year old son and cut the barrel and stock down to fit him (ala Chipmunk). He has a hard time getting a good cheek weld on my Marlin 60 when he holds it under his arm. If the butt is against his shoulder, he can't reach the trigger.

    Is there a formula or rule of thumb for figuring the correct length of pull depending on height, arm length, etc.?
     
  2. fal 4 me

    fal 4 me Member

    Joined:
    Mar 31, 2006
    Messages:
    122
    Location:
    Wisconsin
  3. LHB1

    LHB1 Member

    Joined:
    Feb 7, 2005
    Messages:
    873
    Location:
    Houston
    Sorry, I don't buy that old song about the distance from elbow to hand for measuring stock length. Doesn't take into account several other factors that affect the length of stock needed. Buy the gun and cut the stock off 1 inch at a time until you get to the length he can handle. Have him wear the same clothes during fitting as he will wear when shooting the gun. Thicker clothing, jacket especially, can require a shorter LOP than shooting in shirt sleeves.

    Good shooting and be safe.
    LB
     
  4. DogBonz

    DogBonz Member

    Joined:
    Sep 23, 2006
    Messages:
    2,068
    Location:
    NJ
    I don't know....

    But Great question. I'm all ears.

    Btt
     
  5. Don't Tread On Me

    Don't Tread On Me Member

    Joined:
    Jul 19, 2004
    Messages:
    2,213
    Location:
    FLORIDA
    You measure from the center of the trigger to end of the stock at the center of the buttplate/pad to get LOP on the rifle.


    This isn't a standard, but many like to measure from the opposite side of the elbow (where the crease is) across the forearm to the tip of the trigger finger. You take that measurement, then either add or subtract 1" (can't remember).


    The best thing to do is to find a stock that fits well. Determine this by visually inspecting the hold and the mechanics of stance, where the arms are, is there scrunching, is there reaching etc....if good, measure that rifle and use it as a guideline. I'm sure a GOOD gunshop that has helpful staff and decent inventory would be willing to assist in trying out different rifles for a fit on your child. Gunshop prices are higher, but that's what I expect for some customer service. That's assuming the gunshop is nice.
     
  6. 1911 guy

    1911 guy Member

    Joined:
    May 5, 2005
    Messages:
    6,380
    Location:
    Garrettsville, Oh.
    My formula.

    LOP of the gun has already been discussed, from trigger to buttstock. LOP for the shooter is >usually< from the inside of the elbow to the first joint of the trigger finger. For an adult in cold weather hunting clothes, I'd knock off another two inches for clothing bulk. For a child, an extra inch off should do it because of the proportions.

    When you cut the stock, drill it for dowels first. Then cut the stock in 1" increments. When you need to add length as he grows, you can add sections back on and they will be relatively straight. It won't be pretty, but he'll have a rifle that fits him as he grows and a rifle to pass on to his kids for them to learn on. I bought a cheap romanian .22 bolt action for my son. He'll learn on that, when he's done growing he'll get an "uncut" rifle.
     
Thread Status:
Not open for further replies.

Share This Page