Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

How is a mortar aimed?

Discussion in 'General Gun Discussions' started by Tokugawa, Jul 22, 2007.

Thread Status:
Not open for further replies.
  1. Tokugawa

    Tokugawa Member

    Joined:
    Jun 21, 2005
    Messages:
    1,000
    How is an indirect fire weapon like a mortar aimed? If the shooter and target are hidden in dead ground, you would need a spotter, yes? Is this all done with "old" tech, or do we use a lazer rangefinder and direction (compass point) finder coupled with a gps to establish the target coordinates and transmit to shooter/ I.E.- the spotter know his gps position, shooters gps position, and distance and angle to target, and computer figures targets gps position, and direction and trajectory from the shooter?
     
  2. bogie

    bogie Member

    Joined:
    Jan 2, 2003
    Messages:
    9,569
    Location:
    St. Louis, in the Don't Show Me state
    It's usually aimed very carefully, sometimes due to directions being given by a 2nd Lt. who is carrying both a compass and a map.
     
  3. Ron James

    Ron James Member

    Joined:
    Apr 22, 2006
    Messages:
    2,336
    Location:
    Arizona
    And being a Retired CSM, I can tell you for a fact, both the mortar and the 2nd LT. with a map, are equally dangerous. :)
     
  4. Alphazulu6

    Alphazulu6 member

    Joined:
    Jun 2, 2007
    Messages:
    809
    Location:
    Colorado
    I hope the PSG is standing nearby..... HAHA

    Ok seriously not to bash a 2LT (I know how it feels to be one) A mortar is aimed using a "sight" that is set up for Mils (not degrees). It is really not all that hard just that the trajectory, elevation, windage, type of target all have to be determined. And a good E-6 mortar section sergeant will take care of that!
     
  5. rangerruck

    rangerruck Member

    Joined:
    Jan 12, 2006
    Messages:
    8,374
    Location:
    Texas, baby!
    you could use a spotter, but that is not 100 percent necessary. if you can read a map, and have a target you wish to acquire, you can do it, but you still would need someone, with a pair of binos, with you , at a minimum, from your position, to see if you have hit your target. if you are say, close enough with a first or second shot, or even a third, you can then fire for effect, rain down the rest of your ammo on that spot, and if you have other mortars, in you platoon or company, they just light up the same area you are shooting into.
     
  6. Jdude

    Jdude Member

    Joined:
    Jul 19, 2007
    Messages:
    380
    2Lts are not to be trusted with a map. Ever.

    As to the mortar: Usually it is a Spc. (army) or LCpl (marines) with a chart of known ballistic flightpaths. That soldier selects the approriate flightpath for his chosen range and time of flight, points the tube accordingly, and after an okay from his superiors, lets one go.
     
  7. Jubjub

    Jubjub Member

    Joined:
    Sep 10, 2004
    Messages:
    787
    They have an optical sight that is attached to the gun. If the target is in sight (rare for mortar fire) they can aim directly at it. More commonly, they sight on an aiming stake placed in the ground 50 or 100 meters from the mortar, and just use the sight as a reference.
     
  8. Hank Zudd

    Hank Zudd Member

    Joined:
    Jun 15, 2003
    Messages:
    178
    Location:
    Bastrop, TX
    How is a mortar fired?

    Practice.

    Don't know about all mortars, but some are hastily setup & fired as mostly described above. However with larger calibers, you need a fire direction controller to use some trig to determine the guns position relative to the target. I shot 155's & it takes a little time (couple hours) to setup an accurate battery. "Spotters" are commonly called forward observers; they direct the fire adjustment relative to the target & where the first shot hit. I shot 100's of rounds & never saw where they hit; that's the FO's job.:uhoh:
     
  9. Smith357

    Smith357 Member

    Joined:
    Feb 19, 2005
    Messages:
    1,024
    Location:
    Columbus, Ohio
    USMC 81mm Mortarman

    First sighting posts are set out at a known compass heading. From there coordinates for a fire mission are calculated by the FDC (fire direction control) and settings are relayed to the gunner who puts the settings in the sight and then lines the gun back up on the sighting posts as the ammo men adjust the charge level on the rounds for distance from 1 to 9 increments. Then a single round is dropped down the tube. A forward observer will relay back to the FDC if any adjustments are needed and then they fire for effect. Typical setup time from the mortar being in pieces to dropping the first spotter down the tube is about 3 minutes. Setting the aiming posts takes the most amount of time.
     
  10. AK103K

    AK103K Member

    Joined:
    Dec 27, 2002
    Messages:
    5,774
    Trying to find the "Green Zone" are we? :)
     
  11. daniel (australia)

    daniel (australia) Member

    Joined:
    Dec 25, 2002
    Messages:
    338
    That is fairly much how I remember it too. Your mortar team first plants the baseplate into the ground, sets up the mortar and attaches the sight unit, which has two spirit levels to get the sight level front-to-rear and side-to side. The sighting posts are like what surveyors use, and usually one is set out at a convenient distance in front of each tube and one 180 degrees behind the tube. They are set out carefully using a compass. Actually one would be enough, but the second is there as back-up in case the first is damaged by fire etc.

    When the "2lt with the radio" calls in the fire mission it is received by a mortar fire controller, who has a plotting board over a map showing, amongst other things, where the tubes are and where the fire mission is being called in from. Unless the target has already been ranged, the MFC calculates where the fire is to strike, usually by translating the bearing and range from the bloke with the radio into a bearing and range from the tubes, using the plotting board. He then calculates the charge and elevation necessary to reach that range.

    The charge and projectile are called to the mortar crew/s, and then the bearing and elevation. The mortar No. 1 sets the sight unit to that bearing and elevation, and then adjusts the tube so that the two bubbles are centred again and the crosshairs of the sight are lined up on the aiming post - giving the elevation and bearing respectively, while the No. 3 prepares the rounds with the right charge. At that point all is prepared (if the 2lt hasn't stuffed it all up) for the bringing of bad news to the bad guys away over there.

    BTW all of this, with a good crew, should take only a few short minutes from the tubes being on a vehicle to giving the nervy guy on the radio "shot over".
     
  12. Cannonball888

    Cannonball888 Member

    Joined:
    Jun 7, 2007
    Messages:
    2,172
    Location:
    Florida
    First, you need a crew of 5 people just to load the shell, then you need a half dozen officers to direct the fire :D

    [​IMG]
     
  13. GRIZ22

    GRIZ22 Member

    Joined:
    Nov 4, 2006
    Messages:
    5,035
    I shot 155's & it takes a little time (couple hours) to setup an accurate battery.

    That is really slow and wouldn't get you out of gun bunny school at Fort Sill.

    If a mortar or artillery piece is set up and has time to register (shoot at a known location) where the fire is adjusted visually everything else is shooting from a known point and is very accurate unobserved fire.

    Unobserved fire is avoided if possible as all the variables can put you off target and shooting dirt has no effect on the enemy.
     
  14. Aguila Blanca

    Aguila Blanca Member

    Joined:
    Sep 1, 2006
    Messages:
    1,693
    That must be a VERY large mortar.
     
  15. brickeyee

    brickeyee Member

    Joined:
    Feb 25, 2005
    Messages:
    3,135
  16. Hank Zudd

    Hank Zudd Member

    Joined:
    Jun 15, 2003
    Messages:
    178
    Location:
    Bastrop, TX
    reply to

    Griz22- from the time the advanced party occupies a firing point, lays out a point for each gun, gun crews roll in & set aiming stakes, checks backsight to FDC, sets gun ready, set cammo netting (15 min for all these task) it's at least an hour. Course doctrine has changed since early 90's when I was doing this. (Pallin was just comming online) Your right, to occupy a spot & get rounds down range needs to be quick. I only had a year in the unit till I went back to flying, so I never had the chance to occupy a "virgin" firing point. We did do one fire mission, hand ramming 3 rounds in 45 seconds. Of course we're talking about SP arty, not mortars. Mech infrantry divisions have tack mounted 120's.
     
    Last edited: Jul 22, 2007
  17. GRIZ22

    GRIZ22 Member

    Joined:
    Nov 4, 2006
    Messages:
    5,035
    Griz22- from the time the advanced party occupies a firing point, lays out a point for each gun, gun crews roll in & set aiming stakes, checks backsight to FDC, sets gun ready, set cammo netting (15 min for all these task) it's at least an hour. Course doctrine has changed since early 90's when I was doing this.

    OK Hank when you throw all this in I'll agree with that time. I think the ARTEP standard in the late 80s was something like 15 min for a hipshoot. 3 rds in 45 sec with a towed 155 is great time. We put out a round every 40-45 seconds with an 8" in Vietnam for awhile. Yes I know that exceeds sustained rate of fire but sometimes you don't worry about such things.

    I apologize if I offended you. Nice to see guys here who have shot something bigger that a 50 cal.
     
  18. Langenator

    Langenator Member

    Joined:
    Jul 30, 2003
    Messages:
    2,689
    Location:
    Ft Belvoir, VA
    Current mortar calibers in the US inventory: 60mm, 81mm, 120mm. There may also be 4.2" (107mm) mortars left in some NG mechanized units.

    Current artlillery calibers in use: 105mm, 155mm. The 8"/203mm was phased out in favor of the MLRS (227mm rockets)
     
  19. daniel (australia)

    daniel (australia) Member

    Joined:
    Dec 25, 2002
    Messages:
    338
    I probably should add to my post that once you've set up and got the first round out to where the bloke with the radio wanted it it is of course usually necessary for the rounds to be "adjusted" onto the target, using instructions from the bloke who called it in. The mortar crews usually can't see the target and don't need to (which is why it is called "indirect fire").

    The trick to this is that the bloke observing the fall of shot gives adjustments based on his point of view, and these must be converted by the plotter into adjustments from the point of reference of the mortar crew. To do this the plotter again needs to know the position of the observer, and the bearing from the observer to the target. Thus when the observer says "add 100" the plotter recognises that this means "move the fire 100m further in the direction between me and where I said the target is".

    The correction from the point of view of the mortar location may be quite different - for example the observer may be facing 90 degrees to the line between the tubes and the target and thus the observer's "add 100" may require an adjustment to the left from the point of view of the mortar crews.The plotter makes this calculation for the crews, and they adjust according to his instruction.

    With each adjustment a round is fired until the fire is on the mark, and then the full complement - "fire for effect" - is let go.

    I hope I've explained that right. It was a long time ago, and I only did the mortars course so that I'd have a better idea what I was doing when I was out there with my radio, compass and map ;) .
     
  20. Acera

    Acera Member

    Joined:
    May 26, 2007
    Messages:
    3,117
    Location:
    Free State of Texas
    The best manual for this and a lot of different questions is STP-31-18B34. Sometimes you will find it a gun show, or google it. Subject areas 1-8 will give you more information about mortars than you will probably want.
     
  21. James T Thomas

    James T Thomas Member

    Joined:
    Sep 15, 2005
    Messages:
    1,185
    Location:
    Pittsburgh, PA
    adaptation sighting

    A mortar is "aimed" by the combination of elevation; angle to the ground -horizontal, and azimuth; the traverse adjustment -side to side.

    The aiming stakes are the reference. When the closer one obscures the farther one in your sight optics, then you are aligned.

    My unit had to elevate our M29; 81 mm cannon or "tube" almost to the vertical of 1600 mils= 90 deg. Our setting was 1500 mils, i.e. 85 deg.
    The tube had coarse threads on the outside which engaged the collar; that was supported by a bipod legs.
    Fine adjusting was done by turning a crank mechanism; fine threads. It could be disconnected to make large settings. Both in elv. and traverse.
    I believe it was 90 mils traverse available either left or right of center.

    The gunner became very proficient at rapid and accurate cranking. He knew from experience, and training, how many cranks to get how many mils -I forget now. Depends on the number of threads.

    My unit accompanied the rifle platoons out in the field one hot day. We were almost at the range limit of our artillery. We had to erect and set our single mortar (we had three) in an open field of gravel hardpan clay. No digging in for defilade cover! My gunner; Sgt. Charles White of Wash.D.C. manned that sight and made his adjustments under intense fire (three 12.7 mm Russian guns) and we brought fire upon the enemy as close as 80 m from us.
    A burst from the M375 high explosive round had a killing area almost half of that distance, so it was close. But we needed it. We were unable to get our supporting artillery, but did obtain air power later on in the day. Sgt. White lived that day. A brave man. Some of the incoming rounds actually pinged off off that tube!

    We could not set up the aiming stakes so the direction was simply swung to the position of the platoons to our front. They were close enough to observe if you would risk it and get up on your knees.
    Adjustments were by radio communication until they were all (six) destroyed by snipers or the 12.7 guns. Mine was the last one, but we had already fired up the two dozen or so rounds we had been humping that day.

    At the call for fire, we got the first round out in less than two minutes, though I did not time it.

    That is how you expediently aim a mortar.

    Gentlemen: Unless you have experienced this type of thing first hand, please refrain from the officer bashing. If you have "been there," you will know what it means to have that responsability.
     
    Last edited: Jul 23, 2007
  22. 41magsnub

    41magsnub Member

    Joined:
    Jul 10, 2007
    Messages:
    1,791
    Location:
    Missoula Montana
    The movie Stripes provides an excellent example of how to use a mortar.
     
  23. Vern Humphrey

    Vern Humphrey Member

    Joined:
    Dec 30, 2002
    Messages:
    18,502
    Location:
    Deep in the Ozarks
    A mortar is aimed with a variation of a panoramic telescope sight. The sight has a rotating head with hash marks for mils (6400 mils to a circle) and a tilting feature with markings and level tubes (like a carpenter's level.)

    The sight is "boresighted" to the mortar using a strap-on V-block elbow sight device. The V-block ensures the elbow sight is centered on the tube, and witness marks ensure it is on the same center as the panoramic telescope. The two sights are trained on a sighting board a fixed distance away, so the lines of sight for the panoramic signg and elbow sight are parallel.

    The mortar is laid for direction using either an M2 compass or an aiming circle. If the latter is used, it is set up and aligned like a surveying device, and the mortar is "referred" back, adjusting the sight until both the Aiming Circle and the Pan-Tel sight read the same.

    Then the sight is placed on standard lay and aiming stakes put out -- the gunner looks through the sight and directs his assistant gunner in placing out two stakes.

    When a target is detected, firing data is calculated using a computer, firing tables or plotting board. Based on the range, direction (and sometimes altitude) of the target, the deflection (angle to set on the sight), elevation and charge are determined. The deflection is set on the sight and the mortar cranked around until the crosshairs of the sight are back on the aiming stakes. The elevation is set on the sight and the mortar cranked up or down until the bubbles in the levels are centered.

    Depending on how the target was located, the mortar may fire for effect, or the observer may adjust fire. If the latter technique is used, the observer "splits a bracket" -- getting hits over and short of the target. The final bracket may be either 100 meters (for 120mm mortars) or 50 meters for 81 and 60mm mortars.
     
  24. afsenior

    afsenior Member

    Joined:
    Apr 30, 2007
    Messages:
    7
    Location:
    Southwest Missouri
    I know !!!

    I learned several years ago when antelope hunting in Wyoming with a 45-70...

    Art
     
  25. U.S.SFC_RET

    U.S.SFC_RET Member

    Joined:
    Dec 5, 2005
    Messages:
    1,754
    Location:
    The Old Dominion State
    Armies should fear accurate mortar fire, if they don't they quickly will if they ever face them in combat. A good crew can really put the fear of god on you hastily quick. They are calculated for a lot of damage.
     
Thread Status:
Not open for further replies.

Share This Page