Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

I think my scale is to blame...

Discussion in 'Handloading and Reloading' started by BluegrassDan, Sep 12, 2011.

Thread Status:
Not open for further replies.
  1. BluegrassDan

    BluegrassDan Member

    Joined:
    Oct 25, 2008
    Messages:
    213
    Location:
    Elizabethton, TN USA
    I have been having a terrible time getting my .308 Kimber 84M to shoot a 5-shot group consistently under 1.25"-1.5". I've tried 150 and 165 grain bullets, 3 different powders, and dozens of different loads. No matter what, all groups are nearly identical. Factory ammo shoots better. I was using the Lee beam scale that came with my Anniversary kit.

    I was also loading some .30-30 the other day and ran out of bullets, so I put the powder in the cases and came back this evening with a new Frankfort digital scale. For comparison I checked each round and found that the Lee scale was on average .5+ than the Frankfort. Also, the extreme difference between charges ranged .4 +/-. I was aiming for 35 grains and some charges were between 35.4 and 35.8!

    So, I'm going to try reloading some .308 with the new digital scale and see what happens.

    Anyone ever have an experience like this?
     
  2. Naterater

    Naterater Member

    Joined:
    May 16, 2011
    Messages:
    86
    Location:
    Iowa
    My Lee scale is spot on as far as accuracy goes.

    I don't know how close you were getting the beam on the mark with the lee scale. If the beam is off just 1/8 of an inch from the POINT of the mark, there can be a .3-.5 grain difference than the amount it is set to measure.

    Also make sure the metal plate on the pointer side of the beam is centered (or close to centered) between the dampening magnets in the base of the scale.

    It also helps to make sure that the slider on the right is locked with the amount powder you want measured. It does move easily, so push that little plastic pin in to lock the slider. That may also help.

    And I'm assuming the scale is on a nice level surface because that can throw things off.

    I think everyone has had pretty good luck with this scale--check out this thread:
    http://www.thehighroad.org/showthread.php?t=588400&highlight=lee+beam+scale+accuracy

    I hope this Helps!
     
  3. ranger335v

    ranger335v Member

    Joined:
    Dec 3, 2006
    Messages:
    3,797
    "Anyone ever have an experience like this? "

    If you mean an inaccurate digital scale, yeah.
     
  4. hvychev77

    hvychev77 Member

    Joined:
    Mar 13, 2011
    Messages:
    327
    do yourself a BIG favor, and get a good beam scale. i had the same problems with my lee scale and found the RCBS 505 on ebay for 55 bucks or something like that. local gun store wanted almost twice that much. it is so much more accurate and consistent than my lee scale. i have a digital scale too, frankford arsenal, but i seem to always use my RCBS beam scale, especiall when loading for my 300 win mag. .....
     
  5. HOWARD J

    HOWARD J Member

    Joined:
    Mar 8, 2010
    Messages:
    2,185
    Location:
    S/E Michigan
    I also use a RCBS 5-0-5 beam scale
    I have used it for approx. 37 years--it is sill super accurate.
    You can get the same scale from Dillon--"the eliminator"--$55 new
     
  6. Josh45

    Josh45 Member

    Joined:
    Jan 22, 2011
    Messages:
    1,118
    I have the Lee scale and the RCBS 505 scale. I was having a problem with the scale, At least I thought it was the scale. I couldnt get it to stay zeroed so I stopped using it and decided to buy the 505.

    Best choice I ever made. Very accurate and I don't see how you can't make sure its zeroed the way its designed. Also dialing on on your charge is very simple.

    I would recommend the 505 to anyone. Also, I have asked about digital scales and have checked reviews....Digital scales was something I wanted until I asked and read and read. There inaccurate sometimes and so on. So I gave up on that and stood with the beam scale.

    Im much happier and all the loads I have made so far have been fine.
     
  7. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    Something that may help to make your loads more consitent in performance is changing to a slower burnng powder. A slower burning powder will typically produce less variance between charge weights, than a faster burning powder will. Since I don't laod for the .308 all I can use as an example is my 7mm RM. loads. I load with RL22 and wiht the 139 gr. bullet the charge range is form 66 grs. - 69 grs. according to Hornady. The estimated velocity range from the low end to maximum is only around 100 fps. or so as opposed to the estimated velocity v.s. charge variance of a fast burning powder. At 100 yds the variance in velocity is hardly noticable if at all. At 200 yds. this still doesn't really have much of an impact. In consideration of the load you are working with, the variance of .4grs. - .5 grs. would be even less a factor with a typical slow burning powder.
    Another performance indicator in the reloading books is the most accurate data tested is nearly always the slowest burning powder options published for that cartridge. I know now days it is not unusual for a hand loader to pick the powder that is the most economic in terms of usage, but it comes with another expense we need to consider, accuracy and consistency.
     
  8. ArchAngelCD

    ArchAngelCD Member

    Joined:
    Nov 25, 2006
    Messages:
    22,120
    Location:
    Northeast PA, USA
    I would be much more inclined to think the inexpensive digital scale you used is off instead of the Lee scale being off. The only reliable way to check the accuracy of a scale is to use a marked weight (calibration weight) like one that should have come with your digital scale. Don't assume the digital scale is correct and the beam scale is incorrect. I have heard a lot of complaints about a Lee scale but it being inaccurate is not one of them...
     
  9. Bmac1949

    Bmac1949 Member

    Joined:
    Jan 3, 2011
    Messages:
    283
    Location:
    Crockett Texas
    I didn't like the Lee scale when I first got it so I bought a cheap digital scale. It was a waste of money but it did force me to get used to the Lee scale and once I did I realized that it is accrurate. My next purchace will probablly the Dillon Eliminator balance scale.
     
  10. Eb1

    Eb1 Member

    Joined:
    Jan 15, 2008
    Messages:
    3,010
    Location:
    USA
    My Lee Scale was off by as much as .8 to 1.0 grains on a good day.. It was the most inconsistent scale I have ever used.

    I checked it with a Lyman 500, and also with a Dillion Digi scale. I just threw it in the garbage because I didn't want to put anyone in the position of hurting themselves, or beating their head on the table because you loads were all over the place.

    Ditch it!
     
  11. ArchAngelCD

    ArchAngelCD Member

    Joined:
    Nov 25, 2006
    Messages:
    22,120
    Location:
    Northeast PA, USA
    Nothing wrong with a Dillon scale but I really like the RCBS scales which I'm told are made by Ohaus. BUT, I do own a Lee scale and use it at times because it's always 100% correct. (usually to check other scales)
     
  12. rfwobbly

    rfwobbly Member

    Joined:
    Nov 14, 2008
    Messages:
    3,925
    Location:
    Cornelia, GA
    Both the 505 and the Eliminator are made by Ohaus. The beam, specs and features are identical on both units. Dillon sells the Eliminator at list for $54. Midway sells the 505 discounted for $74.
     
  13. Eb1

    Eb1 Member

    Joined:
    Jan 15, 2008
    Messages:
    3,010
    Location:
    USA
    WOW, AACD. My Lee scale was never accurate. You could weigh the powder. Dump it into a different pan. Reset the Lee pan, and dump the powder back into the Lee pan, and it would weigh something different. And all you did was transfer from one pan back to the other. It was crazy mind boggling, and very discouraging.
     
  14. mdi

    mdi Member

    Joined:
    Dec 31, 2007
    Messages:
    1,920
    Location:
    Orygun!
    IMHO only, the only problems I've heard with Lee scales is operator error. Lee scales come with a vernier poise and setting/reading one is difficult for some folks. I have three scales (Lee, Lyman/Ohaus, RCBS 5-0-5). I keep them all clean and on the Lee I use a pencil eraser to clean the pivot (razor blade?) and make sure the beam is centered in the base...
     
  15. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Scales, both beam and digital, must be perfectly level on both axis to be accurate & consistent.
    Once the scale base is leveled front to back and end to end, only then zero the scale.

    You might buy a small bubble level at the hardware store and check the bench top where you use the scales.
    Betcha it isn't level!

    rc
     
  16. JDGray

    JDGray Member

    Joined:
    Sep 16, 2005
    Messages:
    5,131
    Location:
    SW MI.
    I just picked up a Dillon Eliminator scale, and do like it so far, but the chrono will be the true test. I have a Lee scale, and cant tell you how many times I took a little scoop of powder out because it was heavy, only to put it all back plus sum because it was light.

    Good point rc, be sure your bench is spot on level.
     
  17. Eb1

    Eb1 Member

    Joined:
    Jan 15, 2008
    Messages:
    3,010
    Location:
    USA
    You know what they say about opinions.
     
  18. Eb1

    Eb1 Member

    Joined:
    Jan 15, 2008
    Messages:
    3,010
    Location:
    USA
    With the lyman 500 my chrony gives very consistent readings. I quite like the lyman 500. Easy to use and quite accurate as my last load testing shows on another post.
     
  19. ArchAngelCD

    ArchAngelCD Member

    Joined:
    Nov 25, 2006
    Messages:
    22,120
    Location:
    Northeast PA, USA
    That's good to know, thank you for the info...
     
  20. CHEVELLE427

    CHEVELLE427 Member

    Joined:
    Jul 18, 2008
    Messages:
    1,022
    Location:
    NW FLORIDA
    i use a beam and 2 electric scales , also a cheep electronic scale just for checks like i had to do tonight , thought a round might have got skipped of a charge so i just weighted 1000 223 most showed 172-175gn then a 150gn showed its head, bingo a skipped charged, cheep scale saved me from a squib round.

    check and check again.
     
  21. Shimitup

    Shimitup Member

    Joined:
    Feb 27, 2009
    Messages:
    486
    Location:
    Houston
    I thought I'd throw this in too, as ArchAngel said the only way to really know is to get a calibration weight. Just as important is response to changes in weight. Throw a charge and trickle in a few grains of powder and watch for the movement, if it seems sluggish the knife edge could have a ding which could add some friction as will dust and debris in the notch where it rests. A pass with a fine stone will repair the knife edge, a little solvent and compressed air will take care of the notch. You probably know this but just in case, the slightest air movement wreaks havock with a balance beam, depending on your room ventilation you may want to have your scale well protected back in a pocket. Even if the calibration is off if it's consistent it shouldn't be affecting your accuracy at the range, having said that I'm assuming you're using the scale to set a powder measure. If you're using an inconsistent scale and weighing each charge that's another story.
     
  22. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    From the sound of your powder charge for a .308 cartridge it seems you are using a rather fast burning powder. My suggestion even if the groups improve some,would be to load a slow burning powder if accuracy is your ultimate goal and high velocity doesn't bother you. Slow burning powders will perform very consistently even when the powder charge has a rather large spread. This is especially true if your charge is near the middle of the road and up. An example of this is I use RL22 for my 7 mags and the powder charge listed for a particular bullet is 66-70 grains. I've often grabbed a box of 70 gr. charged bullets with great groups (1/2" MOA) and then started shooting another box loaded to 68 grains, this is at 200 yds. for both. The difference in my groups was not at all noticably varied, the chronographed velocity was no more than 50-75 fps. It's just another positive point regarding the slow burning powders.
    Another quality is they deliver maximum potential velocity without having to teeder on excessively high pressures in many applications. Many bench rest shooters, if not all, use only the slow burning ones becasue they are so reliably consistent, especially when the charge is topped out or compressed. Make no mistake though, a proper load work up always applies, regardless of the powder used one must always work up to avoid serious issues that can present!
     
  23. Master Blaster

    Master Blaster Member

    Joined:
    Dec 26, 2002
    Messages:
    4,908
    Location:
    Delaware home of tax free shopping
    you have a 1500 dollar rifle and hundreds of dollars worth of components and you are trusting your precission to Two crappy $25 scales. Hmmm I wonder what the problem could be?
     
  24. scythefwd

    scythefwd Member

    Joined:
    Mar 13, 2008
    Messages:
    3,561
    Location:
    Manassas Park, VA
    I'd check the lee vs. a check weight. Also, if you are having issues with it, move it to a different, level, surface and check it there. Vibrations, air currents, etc... can make the scale read off.

    Master - There aren't many expensive balance beam scales. Most sit at around 50 dollars, but that doesn't mean they are more accurate.
     
  25. Master Blaster

    Master Blaster Member

    Joined:
    Dec 26, 2002
    Messages:
    4,908
    Location:
    Delaware home of tax free shopping
    yes I have an Ohaus labeled by dillon about $50 its been quiet accurate when tested with check weights. If you are reloading rifle a good powder measure Redding , Lyman etc $100-$150 is even better than the scale. Benchrest guys use a $300 harrel and only check with a scale when they change loads. Its all about consistency, Personally I would not trust any consumer level electronic scale to be accurate, but a decent $50-$100 balance set up properly will last a lifetime and be 100% reliable.

    JMHO YMMV
     
Thread Status:
Not open for further replies.

Share This Page