Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ideal height for reloading bench?

Discussion in 'Handloading and Reloading' started by 1KPerDay, Jan 20, 2011.

Thread Status:
Not open for further replies.
  1. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    12,477
    Location:
    Happy Valley, UT
    Well my existing "man cave" table isn't going to be sturdy enough for my new LCT press. So I'm considering putting a reloading "bench" (basically just bolting a sturdy plywood or 2x4 shelf to the studs, so the bench will be across the opening of an unused closet. Any reason I shouldn't? It's not the widest opening but I could theoretically make the shelf deep so I'd have useable bench space behind the press, but not too much to either side. The garage is out; it's too stuffed as is and freezes in the winter.

    Is "belly button height" too high or too low?

    Thanks
     
  2. cheygriz

    cheygriz Member

    Joined:
    Dec 28, 2002
    Messages:
    2,245
    Location:
    High up in the Rockies
    Do you reload standing up or sitting down?

    Do you use a single stage or progressive?

    I like to sit down while reloading on my Dillon progressive. So I built my bench low, so I could use a strong mount, and keep my eyes at the level of where "the action" is going on.

    Depending on how you reload, your bench height will vary.
     
  3. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    12,477
    Location:
    Happy Valley, UT
    Dunno, I've never tried it. All the videos I've seen are guys standing up. Seems to me you'd get more leverage standing up, and can more comfortably see down into the cases to double-check powder, etc. Do you sit on a regular chair or a bar-type stool?
     
  4. oneounceload

    oneounceload member

    Joined:
    Apr 24, 2008
    Messages:
    15,710
    Location:
    Hot and Humid FL
    My bench is about 36" as in what the half-height of my "Gorilla Rack" is, so I use a bar stool to sit on while I reload.

    If your press has good linkage, you won't need a lot of leverage
     
  5. griff383

    griff383 Member

    Joined:
    Jan 20, 2010
    Messages:
    608
    Location:
    Denver
    My LNL is 32" from the floor, I sit when I reload. It is just low enough that I can peek in the case if I need to but still comfortable to operate.
     
  6. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    12,477
    Location:
    Happy Valley, UT
    the top of the bench is 32" from the floor, or press is? Just want to be sure.
     
  7. griff383

    griff383 Member

    Joined:
    Jan 20, 2010
    Messages:
    608
    Location:
    Denver
    Yep, sorry should have said that. The top of the bench is 32" from floor
     
  8. ColtPythonElite

    ColtPythonElite Member

    Joined:
    Jan 8, 2011
    Messages:
    7,353
    My bench is 38" high. I wanted it that high because at 12 ft long, I use it for other things than just the reloading presses. I've got a grinder, vise, and drill press on one end. A work area in the middle, and the presses on the other end. At 38" I can sit on a barstool and load in comfort.
     
  9. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    12,477
    Location:
    Happy Valley, UT
    Thanks guys. CPE, how tall are you if you don't mind me asking?
     
  10. oneounceload

    oneounceload member

    Joined:
    Apr 24, 2008
    Messages:
    15,710
    Location:
    Hot and Humid FL
    Actually, mine is 37.5" off the floor as I put a 1-1/2" plywood top on it (3/4" doubled up)

    With the 24" bar stool, it is comfortable for me - I placed the 2 sections side by side, making the bench 8' long - metallic on one end, shotgun on the other, work space in between
     
  11. winchester1886

    winchester1886 Member

    Joined:
    Jan 17, 2011
    Messages:
    249
    Location:
    Heart Of Texas
    I use a office chair that is adjustable in height.
     
  12. flashhole

    flashhole Member

    Joined:
    May 2, 2005
    Messages:
    1,061
    Location:
    Owego, NY
    I'm 5'9" tall and I like to stand when I load. I built my bench 42" high, it's perfect for me. If I want to sit I use a bar stool.
     
  13. twofifty

    twofifty Member

    Joined:
    Apr 21, 2007
    Messages:
    1,611
    ergonomics

    1K I like your idea of using closet space, as your plywood top will be very secure due to ledgers & wall studs on all sides. A front leading edge of 2x4 will take the flex out of the 3/4" ply. If you bring the bench front to where the door(s) will still close, then you can keep the kids out of your mancave.

    You might also want to think about an overhead storage shelf or shelves for components, tools, dies. Overhead or side lighting is very important so long as it is shadow free and the bulbs present no fire hazard.

    For height, suggest you try mocking up before making things permanent. Consider also at what height you want your scale and powder dispensing system to be. At what height is your scale best read? Maybe you'll end up with the scale set near eye level.
     
  14. TexasShooter59

    TexasShooter59 Member

    Joined:
    Jan 11, 2008
    Messages:
    315
    Location:
    North Texas
    My reloading bench started out as a wood working bench. After using lower tables, I decided that what would work best for me while standing was this: stand up straight, bend arms at 90 degree angle, measure from floor to bottom of elbows. I built a table to this height and I never had any regrets about the height. Now as a reloading table, it is about 4 inches higher due to location on a raised floor ledge. This may be just a little too high but works well for seeing the balance scale and looking at the cartridges in the press from the side.
     
  15. jbrown13

    jbrown13 Member

    Joined:
    Jan 2, 2009
    Messages:
    159
    Location:
    Perry, Georgia
    I think it depends on how tall you are and how long your arms are. I stand when I reload, and I want the lever at its lowest point to be at a point where I don't have to bend over or flex my knees to keep my hand on the ball. For me that turned out to be 43" for a LNL AP with a larger than standard ball on the handle. I'm 5'-9" tall and wear a 33" sleeve length.
     
  16. James2

    James2 Member

    Joined:
    Nov 27, 2009
    Messages:
    878
    Location:
    Northern Utah
    My bench is 30 inches, the same height as a dining room table. I use a regular chair and sit while loading. I am using a single stage press.
     
  17. GLOOB

    GLOOB Member

    Joined:
    Sep 16, 2007
    Messages:
    5,940
    bench: 35 1/2"
    press: Lee Breechlock
    me: 6'
    office chair: ~19", perfect height.
     
  18. Hagen442

    Hagen442 Member

    Joined:
    Jan 6, 2006
    Messages:
    199
    Location:
    The Dodge House , NC
    Nothing

    Nothing
     
    Last edited: Jan 21, 2011
  19. DM~

    DM~ Member

    Joined:
    Jan 6, 2011
    Messages:
    2,170
    Location:
    upper mid west
    I built my bench to be comfortable to use when standing, if i sit, i'll use a taller chair! It's easier to change the chair than the bench...

    DM
     
  20. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    12,477
    Location:
    Happy Valley, UT
    Thanks for more great ideas, guys. I'm 6'3" with a long torso and gorilla arms. I'll have to do some figurin'. Hmmmm....

    twofifty I'd intended to leave enough clearance to close the closet door with the press mounted, and have storage shelves above/behind, but I hadn't thought to have a shelf for the scale nearer to eye level. I like that idea... Also need to consider lighting. Hmmm....
     
  21. Trikerider

    Trikerider Member

    Joined:
    Dec 20, 2010
    Messages:
    40
    Location:
    Iowa
    Mine is 30 1/2 to top of bench. Bottom of press is 31 1/2 as have it on board and that board bolted to bench. I am older and sit when reloading. trikerider
     
  22. WNC Seabee

    WNC Seabee Member

    Joined:
    Jul 7, 2008
    Messages:
    733
    Location:
    Hendersonville, NC
    I'm 6'4" and load standing up.

    I just built a bench that is 43" to the top of the table. Dillon 550 mounted to the bench without their strong mount feels perfect to me.
     
  23. WNTFW

    WNTFW Member

    Joined:
    Jul 16, 2006
    Messages:
    1,906
    My table is right at 38". The presses are above the table. One is Dillon 550 with a strong mount & plate that allows it to be moveable. The single stages up raised & moveable as well.

    Elbow height was a good suggestion from that ole boy in Texas.
    I am guessing my 550 is about the same height as WNC Seabee's press.

    I'm about 5'10"

    I never did like to sit to reload. I think being on my feet lets me move as needed.
     
  24. jeadams

    jeadams Member

    Joined:
    Dec 14, 2010
    Messages:
    28
    I am 6'2" & I built mine @ 43" from the floor. To me it is "Bar" height & I can sit on a shop stool or stand with no issues.
     
  25. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    45,610
    Location:
    Alabama
Thread Status:
Not open for further replies.

Share This Page