Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Just got a Winchester 94 with williams sight

Discussion in 'Rifle Country' started by PonyKiller, Dec 31, 2011.

Thread Status:
Not open for further replies.
  1. PonyKiller

    PonyKiller Member

    Joined:
    Oct 6, 2011
    Messages:
    257
    Location:
    Southern New Jersey
    just got a winchester 94, ran the serial numbers on the net and it apears to be built in '62. gonna give her a good tear down and cleaning, it's been sitting for a very long time. It has a reciever mounted williams peep sight, here's where the questions start. It still has the original sight up on the barrel, without adjusting the peep sight the factory iron's are more or less in the way. It doesn't appear to be removable from the barrel, kinda scratching my head on how to remove it without destroying it. Once i get that kink worked out, and get her cleaned up, it's range time! After that if things fall my way, NY rifle season next fall.
     
  2. Abel

    Abel Member

    Joined:
    Jan 30, 2010
    Messages:
    2,005
    Location:
    Eastern CONUS
    Take a wooden dowel and a hammer and drift it out of the dovetail groove from left to right. You can buy a dovetail blank to fit into the groove so that the dovetail doesn't get bent and it looks good.
     
  3. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
  4. PonyKiller

    PonyKiller Member

    Joined:
    Oct 6, 2011
    Messages:
    257
    Location:
    Southern New Jersey
    here are some pictures of it.
     

    Attached Files:

  5. Sav .250

    Sav .250 Member

    Joined:
    Jun 5, 2007
    Messages:
    3,409
    Location:
    Central Fla
    A pre-1964,don`t mess it up. :)
     
  6. CTPhil

    CTPhil Member

    Joined:
    May 31, 2010
    Messages:
    281
    Location:
    NW Connecticut
    From the point people are making about how to drive the sight out, does that mean that the dovetail has a taper?
     
  7. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    No, but the sight dovetail probably does, just from the beginning wear pattern from being driven on if nothing else.

    It has long been traditional to drive pins and sights in right to left, and out left to right.

    Doing it the other way will cause further wear to one or the other dovetail or pin & hole, and eventually make them looser.

    But anymore, who knows what the manufactures do??

    Some of the modern guns I have replaced sights on went the other way, like the Springfield XD for instance.

    rc
     
  8. SwampWolf

    SwampWolf Member

    Joined:
    Sep 18, 2005
    Messages:
    3,928
    Location:
    North Central Ohio
    By "right to left" (or "left to right"), I assume the directions have to do with as when holding the rifle-that is, from the butt as opposed to from the muzzle. Right?
     
  9. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Right!

    Muzzle is 12:00 oclock.
    Butt is 6:00.
    Right is 3:00.
    Left is 9:00.

    Or, your military right.

    rc
     
  10. 7.62 Nato

    7.62 Nato Member

    Joined:
    Aug 8, 2009
    Messages:
    799
    Location:
    Michigan
    Hard to tell from the pic, but try removing the rear sight elevator (wedge) to see if that clears the line of sight.
     
  11. aHFo3

    aHFo3 Member

    Joined:
    Nov 21, 2008
    Messages:
    549
    Location:
    Redmond, OR
    Good looking lever gun. It looks like it needs to be used more! Is it a 30-30?
     
  12. Ghost Tracker

    Ghost Tracker Member

    Joined:
    Nov 8, 2006
    Messages:
    1,449
    Location:
    Kentucky Backwoods
    Congrats on a fine Winchester that already HAS a great Williams Peep sight. Enjoy that rifle, but take it to a reputable gun smith BEFORE you try any OJT (On-the-Job Training). It's too nice to "learn-by-doing" unless you're a precise & experience hobbyist.
     
  13. PonyKiller

    PonyKiller Member

    Joined:
    Oct 6, 2011
    Messages:
    257
    Location:
    Southern New Jersey
    Yup it is a 30-30.

    Removing the elevator wedge made little difference.

    I am really liking the williams sight on there, seems to be pretty sturdy, and easily adjusted. The barrel is clear now gonna do some reading up on dissasembly and such and going to give it a through cleaning, and remove the rear sight. If i'm unsure at that point or see anything funky, i'll drop it off to the gunsmith.

    Thanks for all the advice! i can't wait to get it down the range.
     
Thread Status:
Not open for further replies.

Share This Page