Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Kel-tec P3AT problems... ammo or gun?

Discussion in 'Handguns: Autoloaders' started by essayons21, Sep 23, 2010.

Thread Status:
Not open for further replies.
  1. essayons21

    essayons21 Member

    Joined:
    Aug 4, 2008
    Messages:
    1,232
    Location:
    Down by the rivah, VA
    Shot my Keltec today, which doesn't get much range time for obvious reasons to those who shoot them. First magazine was Hornady Critical Defense, supposedly high dollar defensive ammunition. It had been sitting in the gun for a few months and needed to be shot at the range before being replaced. Second round wouldn't shoot, nice primer strike, but nothing. Reloaded tried shooting it 2 more times, firing pin hit the same spot, still nothing.

    Then I shot about 100 rounds of Remington 88gr JHPs, and had two identical problems. Good looking primer strike, but no matter how many times I tried they just wouldn't shoot. Comparing the firing pin strikes on a fired case vs the rounds that wouldn't fire, they were not noticeable different.

    Both these boxes of ammo were bought during the ammo craze of 2009-2010. Is this just poor ammo QC or something wrong with my kel-tec?
     
  2. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    If you are getting good depth on the primer dent and they didn't go off, it is most likely the ammo, or how it was stored.

    One thing to check though is fouling in the chamber.

    If the round stops short of the headspace shoulder in the chamber due to accumulated powder fouling, some the firing pin energy / speed has to be used up to finish seating the round in the chamber before it gets around to denting the primer.

    rc
     
  3. essayons21

    essayons21 Member

    Joined:
    Aug 4, 2008
    Messages:
    1,232
    Location:
    Down by the rivah, VA
    Hmm. The first problem was the 2nd round out of a clean gun, so I doubt fouling was the issue. Storage was in a sealed ammo can in a climate controlled house, for no more than a year. The gun maybe had 200 rounds through it before this.

    Anyone else with a Keltec or similar design have this problem?
     
  4. Al Thompson

    Al Thompson Moderator Staff Member

    Joined:
    Dec 21, 2002
    Messages:
    8,847
    Location:
    South Carolina
    I'd chuck a .38 brass brush in a drill and polish the chamber a bit. :) Flitz also helps.

    FWIW, I found that my P32 really runs better when I used a grease to lube the slide rails....
     
  5. Shadow 7D

    Shadow 7D Member

    Joined:
    Nov 30, 2008
    Messages:
    7,005
    Location:
    Frozen North
    The lint can definably cause a problem, why I grease the insides, lightly oil the rest and put dry lube where the lint seesm to hide. Many people have issue with such little guns due to limpwristing, But I really doubt that's your problem, if the gun shoots other ammo fine, maybe you need to change, or call Hornady and see if they will send you a box.
     
  6. chihuahuatn

    chihuahuatn Member

    Joined:
    Mar 30, 2007
    Messages:
    145
    Location:
    (Dirty South)
  7. MICHAEL T

    MICHAEL T Member

    Joined:
    Feb 3, 2004
    Messages:
    6,011
    Location:
    outback Kentucky
    I go with the ammo problem
     
Thread Status:
Not open for further replies.

Share This Page